The door side airbag sensor LH circuit consists of the airbag sensor assembly and door side airbag sensor LH.
The door side airbag sensor LH detects impacts to the vehicle and sends signals to the airbag sensor assembly to determine if the airbag should be deployed.
DTC B1608, B1617/84, B1618/84 is stored when a malfunction is detected in the door side airbag sensor LH circuit.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B1627/82 | Lost communication with Side Airbag Sensor LH | One of the following conditions is met:
·
The airbag sensor assembly detects a line short circuit signal, open circuit signal, short circuit to ground signal or short circuit to B+ signal in the door side airbag sensor LH circuit for 2 seconds.
·
A door side airbag sensor LH malfunction.
·
An airbag sensor assembly malfunction. |
·
Floor wire
·
Door side airbag sensor LH
·
Airbag sensor assembly |
| B1628/82 | Side Airbag Sensor Assembly LH Initialization Incomplete | One of the following conditions is met:
·
The airbag sensor assembly detects a line short circuit signal, open circuit signal, short circuit to ground signal or short circuit to B+ signal in the door side airbag sensor LH circuit for 2 seconds.
·
A door side airbag sensor LH malfunction.
·
An airbag sensor assembly malfunction. |
·
Floor wire
·
Door side airbag sensor LH
·
Airbag sensor assembly |
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
When disconnecting and reconnecting the battery
When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART
After replacing the airbag sensor assembly, refer to initialization.
Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Check that the connectors are properly connected to the airbag sensor assembly and front airbag sensor LH.
| Proceed to |
|---|
| The connectors are properly connected |
| The connectors are not properly connected |
The connectors are properly connected
The connectors are not properly connected
Disconnect the connectors from the airbag sensor assembly and door side airbag sensor LH.
| *1 | Door Side Airbag Sensor LH |
| *2 | Airbag Sensor Assembly |
| *3 | Floor Wire |
Check that the connectors (on the airbag sensor assembly side and door side airbag sensor LH side) are not damaged.
| Proceed to |
|---|
| The connectors are not deformed or damaged |
| The connectors are deformed or damaged |
The connectors are not deformed or damaged
The connectors are deformed or damaged
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
| *1 | Door Side Airbag Sensor LH | *2 | Airbag Sensor Assembly |
| *3 | Floor Wire | *4 | Connector C |
| *5 | Connector B | *6 | Service Wire |
| *a | Front view of wire harness connector (to Door Side Airbag Sensor LH) |
*b | Rear view of wire harness connector (to Airbag Sensor Assembly) |
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| S26-2 (BBL+) - Body ground | Ignition switch ON | Below 1 V |
| S26-1 (BBL-) - Body ground | Ignition switch ON | Below 1 V |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Using a service wire, connect terminals 8 (BBL+) and 15 (BBL-) of connector B.
Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| S26-2 (BBL+) - S26-1 (BBL-) | Always | Below 1 Ω |
Disconnect the service wire from connector B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| S26-2 (BBL+) - S26-1 (BBL-) | Always | 1 MΩ or higher |
| S26-2 (BBL+) - Body ground | Always | 1 MΩ or higher |
| S26-1 (BBL-) - Body ground | Always | 1 MΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Door Side Airbag Sensor RH |
| *2 | Airbag Sensor Assembly |
Connect the connectors to the airbag sensor assembly.
Interchange the door side airbag sensor LH with RH and connect the connectors to them.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in memory.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC B1627/82 or B1628/82 is output | A |
| DTC B1622/81 or B1623/81 is output | B |
| DTC B1622/81, B1623/81, B1627/82 and B1628/82 are not output | C |
Codes other than DTC B1622/81, B1623/81, B1627/82 and B1628/82 may be output at this time, but they are not related to this check.
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Return the door side airbag sensor RH and LH to their original positions and connect the connectors to them.
A
B
C