Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › from 2022.09
RM25T0E _58 Vehicle Interior _029929 SUPPLEMENTAL RESTRAINT SYSTEMS _0138307 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1905/74  Short in Front Pretensioner Squib LH Circuit  B1906/74  Open in Front Pretensioner Squib LH Circuit  B1907/74  Short to GND in Front Pretensioner Squib LH Circuit  B1908/74  Short to B+ in Front Pretensioner Squib LH Circuit  


DESCRIPTION

The front pretensioner LH circuit consists of the airbag sensor assembly and front seat outer belt assembly LH.

This circuit instructs the SRS to deploy when deployment conditions are met.

These DTCs are stored when a malfunction is detected in the front pretensioner LH circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area
B1905/74 Short in Front Pretensioner Squib LH Circuit One of the following conditions is met:
·

The airbag sensor assembly detects a line short circuit signal 5 times in the front pretensioner LH circuit during the primary check.

·

A front seat outer belt assembly LH malfunction.

·

An airbag sensor assembly malfunction.


·

Floor wire

·

Front seat outer belt assembly LH

·

Airbag sensor assembly


B1906/74 Open in Front Pretensioner Squib LH Circuit One of the following conditions is met:
·

The airbag sensor assembly detects an open circuit signal in the front pretensioner LH circuit for 2 seconds.

·

A front seat outer belt assembly LH malfunction.

·

An airbag sensor assembly malfunction.


·

Floor wire

·

Front seat outer belt assembly LH

·

Airbag sensor assembly


B1907/74 Short to GND in Front Pretensioner Squib LH Circuit One of the following conditions is met:
·

The airbag sensor assembly detects a short circuit to ground signal in the front pretensioner LH circuit for 0.5 seconds.

·

A front seat outer belt assembly LH malfunction.

·

An airbag sensor assembly malfunction.


·

Floor wire

·

Front seat outer belt assembly LH

·

Airbag sensor assembly


B1908/74 Short to B+ in Front Pretensioner Squib LH Circuit One of the following conditions is met:
·

The airbag sensor assembly detects a short circuit to B+ signal in the front pretensioner LH circuit for 0.5 seconds.

·

A front seat outer belt assembly LH malfunction.

·

An airbag sensor assembly malfunction.


·

Floor wire

·

Front seat outer belt assembly LH

·

Airbag sensor assembly



WIRING DIAGRAM

C363915E05
0.521,3.229 3.073,3.542 2.552,0.313 10 false Front Seat Outer Belt Assembly LH 2.177,1.563 4.729,1.875 2.552,0.313 10 false L+ 2.188,2.375 4.74,2.688 2.552,0.313 10 false L- 4.771,1.635 7.156,1.844 2.385,0.208 10 false PL+ 4.771,2.5 7.156,2.708 2.385,0.208 10 false PL- 4.625,4.323 6.281,4.656 1.656,0.333 10 false Airbag Sensor Assembly 0.521,3.031 3.073,3.344 2.552,0.313 10 false S27 4.615,4.146 6.354,4.51 1.74,0.365 10 false S24 2.458,1.552 5.01,1.865 2.552,0.313 10 false 1 2.458,2.375 5.01,2.688 2.552,0.313 10 false 2 4.49,1.542 7.042,1.854 2.552,0.313 10 false 2 4.49,2.365 7.042,2.677 2.552,0.313 10 false 1

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When disconnecting and reconnecting the battery

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

After replacing the airbag sensor assembly, refer to initialization.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE



HINT:

To perform the simulation method, enter check mode (signal check) with the GTS (Click here Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE), and then wiggle each connector of the airbag system or drive the vehicle on various types of road (Click here Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


PROCEDURE

1.CHECK FRONT SEAT OUTER BELT ASSEMBLY LH
a.
C213953C12
0.396,2.156 0.792,2.427 0.396,0.271 2.01,2.323 2.198,2.542 2.198,2.542 2.313,2.542 true 0.792,0.479 0.979,0.656 0.188,0.177 10 false *1 2.01,1.271 2.188,1.448 0.177,0.177 10 false *2 1.604,1.5 1.792,1.677 0.188,0.177 10 false *a 2.323,2.448 2.688,2.615 0.365,0.167 10 false *4 2.292,1.948 2.469,2.125 0.177,0.177 10 false *3 0.49,2.198 0.813,2.417 0.323,0.219 10 false S27 1.781,0.667 1.906,0.844 0.125,0.177 10 false A 1.229,0.875 1.354,1.052 0.125,0.177 10 false C 1.031,0.875 1.156,1.052 0.125,0.177 10 false D
*1 Front Seat Outer Belt Assembly LH
*2 Airbag Sensor Assembly
*3 Connector C
*4 SST
*a Front view of wire harness connector
(to Front Seat Outer Belt Assembly LH)


Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect the connector from the front seat outer belt assembly LH.


d.

Connect the white wire side of SST (resistance: 2.1 Ω) to connector C.

CAUTION:

Never connect the tester to the front seat outer belt assembly LH for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting SST.

·

Insert SST straight into the terminals of the connector.




SST
09843-18061  

e.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Clear the DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

h.

Turn the ignition switch off.


i.

Turn the ignition switch to ON, and wait for at least 60 seconds.


j.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
Result:
Proceed to
DTC B1905/74, B1906/74, B1907/74 or B1908/74 is not output
DTC B1905/74, B1906/74, B1907/74 or B1908/74 is output


HINT:

Codes other than DTC B1905/74, B1906/74, B1907/74 and B1908/74 may be output at this time, but they are not related to this check.



k.

Turn the ignition switch off.


l.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


m.

Disconnect SST from connector C.



DTC B1905/74, B1906/74, B1907/74 or B1908/74 is not output

REPLACE FRONT SEAT OUTER BELT ASSEMBLY LH

DTC B1905/74, B1906/74, B1907/74 or B1908/74 is output

2.CHECK CONNECTORS
2.CHECK CONNECTORS
a.

Disconnect the connectors from the airbag sensor assembly.


b.
C208251C25
0.646,0.792 0.875,0.969 0.229,0.177 10 false *1 1.271,0.781 1.5,0.958 0.229,0.177 10 false *2 0.865,1.281 1.094,1.458 0.229,0.177 10 false D 1.094,1.281 1.323,1.458 0.229,0.177 10 false C 1.906,1 2.135,1.177 0.229,0.177 10 false A 2.177,1.688 2.406,1.865 0.229,0.177 10 false *3 1.49,1.281 1.719,1.458 0.229,0.177 10 false B
*1 Front Seat Outer Belt Assembly LH
*2 Floor Wire
*3 Airbag Sensor Assembly


Check that the connectors (on the airbag sensor assembly side and front seat outer belt assembly LH side) are not damaged.

OK:

The lock button is not disengaged, and the claw of the lock is not deformed or damaged.



Result:
Proceed to
OK
NG



OK

3.CHECK FLOOR WIRE

NG

REPLACE FLOOR WIRE

3.CHECK FLOOR WIRE
a.
C213954C13
0.417,2.094 0.813,2.365 0.396,0.271 1.573,2.219 1.323,2.531 1.323,2.531 1.188,2.531 true 1.75,2.219 2.052,2.542 2.052,2.542 2.177,2.542 true 0.677,0.469 0.865,0.646 0.188,0.177 10 false *1 2.031,1.24 2.208,1.417 0.177,0.177 10 false *3 1.573,1.573 1.76,1.75 0.188,0.177 10 false *a 2.146,1.917 2.323,2.094 0.177,0.177 10 false *4 0.49,2.146 0.802,2.385 0.313,0.24 10 false S27 1.823,0.656 1.948,0.833 0.125,0.177 10 false A 1.031,0.917 1.156,1.094 0.125,0.177 10 false C 1.448,0.917 1.573,1.094 0.125,0.177 10 false B 0.833,0.906 0.958,1.083 0.125,0.177 10 false D 1.208,0.49 1.396,0.667 0.188,0.177 10 false *2 0.875,2.448 1.177,2.594 0.302,0.146 10 false L+ 2.229,2.448 2.531,2.594 0.302,0.146 10 false L-
*1 Front Seat Outer Belt Assembly LH
*2 Floor Wire
*3 Airbag Sensor Assembly
*4 Connector C
*a Front view of wire harness connector
(to Front Seat Outer Belt Assembly LH)


Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
S27-1 (L+) - Body ground Ignition switch ON Below 1 V
S27-2 (L-) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
S27-1 (L+) - S27-2 (L-) Always Below 1 Ω



g.

Release the activation prevention mechanism built into connector B.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM


h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
S27-1 (L+) - S27-2 (L-) Always 1 MΩ or higher



i.

Restore the released activation prevention mechanism of connector B to its original condition.


j.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
S27-1 (L+) - Body ground Always 1 MΩ or higher
S27-2 (L-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK DTC

NG

REPLACE FLOOR WIRE

4.CHECK DTC
a.
C146268C13
0.76,0.438 0.948,0.615 0.188,0.177 10 false *1 1.948,1.281 2.135,1.469 0.188,0.188 10 false *2 0.979,0.865 1.135,1.031 0.156,0.167 10 false D 1.104,0.865 1.26,1.042 0.156,0.177 10 false C 1.646,0.656 1.802,0.833 0.156,0.177 10 false A
*1 Front Seat Outer Belt Assembly LH
*2 Airbag Sensor Assembly


Connect the connectors to the front seat outer belt assembly LH and airbag sensor assembly.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.


d.

Clear the DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
Result:
Proceed to
DTC B1905/74, B1906/74, B1907/74 or B1908/74 is not output
DTC B1905/74, B1906/74, B1907/74 or B1908/74 is output


HINT:

Codes other than DTC B1905/74, B1906/74, B1907/74 and B1908/74 may be output at this time, but they are not related to this check.




DTC B1905/74, B1906/74, B1907/74 or B1908/74 is not output

DTC B1905/74, B1906/74, B1907/74 or B1908/74 is output