Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › from 2022.09
RM25T0E _58 Vehicle Interior _029929 SUPPLEMENTAL RESTRAINT SYSTEMS _0138307 AIRBAG SYSTEM J

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  SRS Warning Light does not Come ON  


DESCRIPTION

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When disconnecting and reconnecting the battery

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

After replacing the airbag sensor assembly, refer to initialization.*

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE

*: w/ VSC

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

When replacing the combination meter assembly, make sure to replace it with a new one.



PROCEDURE

1.CHECK BATTERY
a.

Measure the battery voltage.

Standard voltage:

11 to 14 V


HINT:
·

It may be possible to tell whether the battery is discharged by operating the horn.

·

If the voltage is below 11 V, recharge or replace the battery before proceeding to the next step.




Result:
Proceed to
OK
NG



OK

2.CHECK CONNECTION OF CONNECTOR

NG

REPLACE OR RECHARGE BATTERY

2.CHECK CONNECTION OF CONNECTOR
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Check that the connector is properly connected to the combination meter assembly.


Result:
Proceed to
The connector is properly connected
The connector is not properly connected



The connector is properly connected

3.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BATTERY AND BODY GROUND)

The connector is not properly connected

CONNECT CONNECTOR PROPERLY

3.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BATTERY AND BODY GROUND)
a.
C212427C08
1.542,0.677 1.906,0.948 0.365,0.271 0.531,1.927 0.698,1.927 0.698,1.927 1.031,1.656 true 2.594,2.031 2.406,2.031 2.406,2.031 2.219,1.677 true 2.74,1.865 2.552,1.865 2.552,1.865 2.417,1.656 true 0.125,0.208 0.438,0.365 0.313,0.156 10 false *a 1.594,0.729 1.906,0.885 0.313,0.156 10 false L25 2.635,1.948 2.948,2.104 0.313,0.156 10 false B 0.26,1.854 0.573,2.01 0.313,0.156 10 false ES 2.76,1.802 3.073,1.958 0.313,0.156 10 false B
*a Front view of wire harness connector
(to Combination Meter Assembly)


Disconnect the connector from the combination meter assembly.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
L25-28 (B) - Body ground Ignition switch ON 11 to 14 V
L25-26 (B) - Body ground Always 11 to 14 V



e.

Turn the ignition switch off.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L25-15 (ES) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK SRS WARNING LIGHT (SHORT TO GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK SRS WARNING LIGHT (SHORT TO GROUND)
a.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


b.

Connect the connector to the combination meter assembly.


c.

Disconnect the connector from the airbag sensor assembly.


d.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


e.

Turn the ignition switch to ON.


f.

Check the SRS warning light condition.

OK:

After the primary check period, the SRS warning light goes off for approximately 10 seconds and then remains on.


HINT:

The primary check period is approximately 6 seconds after the ignition switch is turned to ON.



Result:
Proceed to
OK
NG (w/ VSC)
NG (w/o VSC)



OK

5.REPLACE AIRBAG SENSOR ASSEMBLY

NG (w/ VSC)

NG (w/o VSC)

REPLACE COMBINATION METER ASSEMBLY

5.REPLACE AIRBAG SENSOR ASSEMBLY
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.



d.

Check the SRS warning light condition.

OK:

SRS warning light illuminates normally.



Result:
Proceed to
OK
NG



OK

END (AIRBAG SENSOR ASSEMBLY WAS DEFECTIVE)

NG

REPLACE COMBINATION METER ASSEMBLY