The SRS warning light is located on the combination meter assembly. When the ignition switch is turned from off to ON, the SRS warning light illuminates. If the SRS is normal, the SRS warning light turns off automatically after approximately 6 seconds. If there is a malfunction in the SRS, the SRS warning light remains illuminated even after approximately 6 seconds have passed. When terminals TC and CG of the DLC3 are connected, the DTCs are communicated through SRS warning light blinking patterns.
The SRS warning light is located in the combination meter assembly.
When the SRS is normal, the SRS warning light comes on for approximately 6 seconds after the ignition switch is turned from off on (IG), and then goes off automatically.
If there is a malfunction in the SRS, the SRS warning light comes on to inform the driver of a problem.
When terminals TC and CG of the DLC3 are connected, DTCs are output by the blinking of the SRS warning light.
The SRS is equipped with a voltage-increase circuit (DC-DC converter) in the airbag sensor assembly in case the source voltage drops.
When the battery voltage drops, the voltage-increase circuit (DC-DC converter) functions to increase the voltage of the SRS to normal voltage.
A malfunction in this circuit is not recorded in the airbag sensor assembly. The SRS warning light automatically goes off when the source voltage returns to normal.
The signal to illuminate the SRS warning light is transmitted from the airbag sensor assembly to the combination meter assembly through the CAN communication system.
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
When disconnecting and reconnecting the battery
When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART
After replacing the airbag sensor assembly, refer to initialization.*
Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE
*: w/ VSC
Inspect the fuses for circuits related to this system before performing the following procedure.
When replacing the combination meter assembly, make sure to replace it with a new one.
Check vehicle condition.
| Result | Proceed to |
|---|---|
| w/ VSC | A |
| w/o VSC | B |
A
B
Check if a CAN communication DTC is output.
for LHD with VSC: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for LHD with VSC)>DIAGNOSIS SYSTEM
for RHD with VSC: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for RHD with VSC)>DIAGNOSIS SYSTEM
w/ Pre-collision System: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Pre-collision System)>DIAGNOSIS SYSTEM
| Result | Proceed to |
|---|---|
| DTCs are output (for LHD with VSC) | A |
| DTCs are output (for RHD with VSC) | B |
| DTCs are output (w/ Pre-collision System) | C |
| DTC is not output | D |
A
B
C
D
Measure the voltage of the battery.
11 to 14 V
If the voltage is below 11 V, recharge or replace the battery before proceeding.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Check that the connectors are properly connected to the airbag sensor assembly and combination meter assembly.
The connectors are properly connected.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the connectors from the airbag sensor assembly.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON.
Operate all the components of the electrical system (defogger, wipers, headlights, heater blower, etc.).
| *a | Rear view of wire harness connector (to Airbag Sensor Assembly) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| I51-21 (IG2) - Body ground | Ignition switch ON | 11 to 14 V |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I51-25 (E1) - Body ground | Always | Below 1 Ω |
| I51-26 (E2) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the connector from the combination meter assembly.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON.
| *a | Front view of wire harness connector (to Combination Meter Assembly) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L25-28 (B) - Body ground | Ignition switch ON | 11 to 14 V |
| L25-26 (B) - Body ground | Always | 11 to 14 V |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L25-15 (ES) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK (w/ VSC) |
| OK (w/o VSC) |
| NG |
OK (w/ VSC)
OK (w/o VSC)
NG
| *a | Rear view of wire harness connector (to Airbag Sensor Assembly) |
| *b | Front view of wire harness connector (to Combination Meter Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I51-11 (LA) - L25-18 (A/B) | Always | Below 1 Ω |
| I51-11 (LA) - Body ground | Always | 10 MΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the connector to the combination meter assembly.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 second.
Turn the ignition switch to ON.
| *a | Rear view of wire harness connector (to Airbag Sensor Assembly) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| I51-11 (LA) - Body ground | Ignition switch ON | 11 to 14 V |
Turn the ignition switch to OFF.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
w/ VSC:
Connect the connector to the combination meter assembly.
Turn the ignition switch to ON.
Check the SRS warning light condition.
Make sure that nobody is in the vehicle.
After the primary check period, the SRS warning light goes off for approximately 10 seconds and then remains on.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Replace the airbag sensor assembly.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>CENTER AIRBAG SENSOR ASSEMBLY>REMOVAL
Check the SRS warning light condition.
SRS warning light illuminates normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG