Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (for LHD with VSC) › from 2022.09
RM25T0E _57 Power Source / Network _057931 NETWORKING _0306321 CAN COMMUNICATION SYSTEM(for LHD with VSC) D

NETWORKING  CAN COMMUNICATION SYSTEM(for LHD with VSC)  DIAGNOSIS SYSTEM  


ECUS OR SENSORS WHICH COMMUNICATE THROUGH CAN COMMUNICATION SYSTEM


a.

V Bus

i.

ECM


ii.

Brake actuator assembly (skid control ECU)


iii.

Spiral with sensor cable sub-assembly (steering angle sensor)


iv.

Airbag sensor assembly


v.

Combination meter assembly




CHECK FOR INSTALLED SYSTEMS (ECUS AND SENSORS) THAT USE CAN COMMUNICATION


a.

The systems (ECUs and sensors) that use CAN communication vary depending on the vehicle and optional equipment. Check which systems (ECUs and sensors) are installed on the vehicle.

HINT:

The names of ECUs and sensors shown on the GTS display may differ from those shown in the DTC Table by ECU section that follows.


ECU/Sensor Name GTS Display Installed on
ECM ECM (Engine) All vehicles
Brake actuator assembly (skid control ECU) Skid Control (ABS/VSC/TRAC) All vehicles
Spiral with sensor cable sub-assembly (steering angle sensor) Spiral cable (Steering Angle Sensor) All vehicles
Combination meter assembly Combination Meter All vehicles
Airbag sensor assembly Airbag All vehicles



CAN BUS CHECK


HINT:

The ECUs and sensors that are properly connected to the CAN communication system can be displayed using the GTS.


a.

Using the GTS, select the CAN Bus Check screen.

CAN Bus Check
50007
NOTICE:
·

It may be possible to select buses that do not have ECUs or sensors from the bus selection pull-down menu. This is not a malfunction. (This occurs when optional devices are not on a sub bus that is monitored by a gateway function equipped ECU.)

·

In the bus selection pull down menu, all buses applicable to the model are displayed (e.g. LIN communication buses are also displayed). Therefore, refer to the wiring diagrams to check the names of sub buses for CAN communication.



HINT:

Different connection statuses are indicated by the background color of ECUs and sensors that are displayed.


Explanation of CAN Bus Check Screen
Bus Type Background Color Connection Status
V Bus White Communication has been normal since the start of the CAN bus check.
Yellow Communication stop occurred at least once since the start of the CAN bus check, but communication is currently occurring (unstable communication).
Red Communication was established at least once since the start of the CAN bus check, but communication is currently not occurring (unstable communication).
Not displayed Communication stop has continued since the start of the CAN bus check.*1
Sub bus
(gateway function equipped ECU that does not have history of connected ECUs)*2
White Communication has been normal since the start of the CAN bus check.
Yellow Communication stop occurred at least once since the start of the CAN bus check, but communication is currently occurring (unstable communication).
Red Communication was established at least once since the start of the CAN bus check, but communication is currently not occurring (unstable communication).
Not displayed Communication stop has continued since the start of the CAN bus check.*1
Sub bus
(gateway function equipped ECU that has history of connected ECUs)*3
White Communication has been normal since the start of the CAN bus check.
Yellow Communication stop occurred at least once since the start of the CAN bus check, but communication is currently occurring (unstable communication).
Red Currently not communicating (either of the following):
·

Communication stop has continued since the start of the CAN bus check.

·

Communication was established at least once since the start of the CAN bus check, but communication is currently not occurring (unstable communication).


Not displayed Either of the following:
·

If a gateway function equipped ECU cannot communicate, the sub bus and ECUs connected to the sub bus will not be displayed.

·

If no ECUs are connected to the sub bus, "There is no system found on the Communication Bus" will be displayed.



HINT:
·

Gateway function equipped ECUs relay signals between the ECUs connected to the different buses.

·

*1: ECUs that are present in the vehicle but are not displayed on the CAN Bus Check.

·

*2: Gateway function equipped ECU that does not memorize the sub bus ECUs that are connected to it.

·

*3: Gateway function equipped ECU that memorizes the sub bus ECUs that are connected to it.

·

If none of the connected ECUs are displayed, or there is no response from the vehicle to the GTS, check the DLC3 branch and the V bus main wires for a malfunction.




b.

Observe the connection response screen for approximately 2 minutes to check for a change in connection status of the connected ECUs and sensors.

HINT:
·

If an open occurs in one of the lines of a CAN branch (except DLC3), output from the other branch line (the line that is not open) will be unstable and it may interfere with the response (display) of other ECUs and sensors.

·

If the connection status changes during the inspection, repair the open in the branch line of the ECU or sensor that does not respond (is not detected) and then perform the CAN bus check again.





HOW TO INTERPRET CAN BUS CHECK SCREEN


a.

When a communication stop is currently occurring, the probable malfunctioning part can be determined from the CAN bus check and by using the following methods.

NOTICE:

The following CAN bus wiring diagram is provided only as an example. This wiring diagram is different from the actual wiring diagram for this vehicle.


HINT:
·

When a communication stop is currently occurring, it is easier to determine the probable malfunctioning part from the CAN bus check rather than from communication DTCs.

·

Wait for approximately 2 minutes after turning the ignition switch to ON (or simulate the driving conditions that enable the malfunction to be reproduced) and select the CAN bus check. Then observe the communication status of each ECU on the screen.




b.

If a communication error of only 1 ECU or sensor is indicated on the CAN Bus Check screen, a communication stop of the ECU or sensor is suspected.

Example: Open in both CAN branch wires of ECU B on the V bus

C240692C04
5.875,0.073 6.135,0.333 0.26,0.26 10 *a 0.375,3.219 1.042,3.604 0.667,0.385 10 DLC3 5.875,0.542 6.135,0.802 0.26,0.26 10 *b 5.479,1.042 5.74,1.302 0.26,0.26 10 *c 5.479,1.563 5.74,1.823 0.26,0.26 10 *d 5.573,2.073 5.833,2.333 0.26,0.26 10 *e 4.292,3.031 4.552,3.292 0.26,0.26 10 *f
*a V Bus *b Sub bus
*c Terminating Resistor *d Location of malfunction
*e Not displayed or background color changes to red or yellow *f CAN Bus Check screen


HINT:

When there are communication stops, ECUs are present in the vehicle even though they are not displayed on the CAN Bus Check screen.



c.
C240693C04
0.271,1.708 0.51,1.906 0.24,0.198 10 *a 2.885,2.438 3.125,2.635 0.24,0.198 10 *b 1.031,2.448 1.271,2.646 0.24,0.198 10 *c
*a Background color periodically changes to yellow or red
*b Not displayed or background color is yellow or red
*c Not displayed


If communication errors for multiple ECUs or sensors are indicated on the CAN Bus Check screen, then a communication stop of the ECU or sensor that shows a more serious communication stop (an ECU or a sensor which is not displayed) is suspected.

Example: Open in a CAN branch wire for ECU D on the V bus

Explanation of CAN Bus Check Screen
Bus Type Background Color Connection Status
V Bus White Communication has been normal since the start of the CAN bus check.
Yellow Communication stop occurred at least once since the start of the CAN bus check, but communication is currently occurring (unstable communication).
Red Communication was established at least once since the start of the CAN bus check, but communication is currently not occurring (unstable communication).
Not displayed Communication stop has continued since the start of the CAN bus check.*1
Sub bus
(gateway function equipped ECU that does not have history of connected ECUs)*2
White Communication has been normal since the start of the CAN bus check.
Yellow Communication stop occurred at least once since the start of the CAN bus check, but communication is currently occurring (unstable communication).
Red Communication was established at least once since the start of the CAN bus check, but communication is currently not occurring (unstable communication).
Not displayed Communication stop has continued since the start of the CAN bus check.*1
Sub bus
(gateway function equipped ECU that has history of connected ECUs)*3
White Communication has been normal since the start of the CAN bus check.
Yellow Communication stop occurred at least once since the start of the CAN bus check, but communication is currently occurring (unstable communication).
Red Currently not communicating (either of the following):
·

Communication stop has continued since the start of the CAN bus check.

·

Communication was established at least once since the start of the CAN bus check, but communication is currently not occurring (unstable communication).


Not displayed Either of the following:
·

If a gateway function equipped ECU cannot communicate, sub bus and ECUs connected to the sub bus will not be displayed.

·

If no ECUs are connected to the sub bus, "There is no system found on the Communication Bus" will be displayed.



HINT:
·

Gateway function equipped ECUs relay signals between the ECUs connected to the different buses.

·

*1: ECUs that are present in the vehicle but are not displayed on the CAN Bus Check screen.

·

*2: Gateway function equipped ECU that does not memorize the sub bus ECUs that are connected to it.

·

*3: Gateway function equipped ECU that memorizes the sub bus ECUs that are connected to it.

·

The example of the CAN Bus Check screen in the illustration shows the result of electrical noise on the CAN bus which is caused by an open in a CAN branch wire of ECU D (output from the other branch line is unstable) and the communication of ECU C is also unstable. In addition, in this example, ECU C is equipped with a gateway function. Therefore, communication is also unstable between the sub bus ECUs of ECU C and the V bus.

·

The example in the illustration shows that ECU D is not displayed on the CAN Bus Check screen. This indicates a more significant communication stop. In this case, a communication stop of ECU D is suspected.




d.
C240694C04
0.24,1.708 0.458,1.938 0.219,0.229 10 *a 2.875,2.438 3.094,2.667 0.219,0.229 10 *a
*a Not displayed or background color changes to red


If a communication error is indicated on both the V bus and sub bus on the CAN Bus Check screen, suspect any communication stop displayed for the V bus first.

Example: Open in both CAN branch wires of ECU C on the V bus

HINT:
·

In the CAN bus check, it is possible to confirm the communication status of ECUs connected to the V bus after connecting the GTS to the DLC3. As for sub buses, it is possible to confirm which sub bus connected ECUs can communicate with a gateway function equipped ECU on the V bus.

·

If a gateway function equipped ECU has a communication error, ECUs connected to the gateway function equipped ECU are also affected, and communication stops will be indicated.

·

The CAN Bus Check screen in the illustration shows that ECU C has a gateway function and a communication stop in ECU C is suspected.




e.
C240695C04
3,1.521 3.188,1.698 0.188,0.177 10 *a
*a Background color changes to yellow or red


If the CAN Bus Check screen indicates a communication stop only in the sub bus, a communication stop in the sub bus is suspected.

Example: Open in both CAN branch wires of ECU G on the sub bus

HINT:
·

A communication error in a sub bus does not affect the V bus or other buses.

·

When a gateway function equipped ECU has memorized the ECUs that are connected to the sub bus, if any of the ECUs connected to the gateway function equipped ECU has a communication error, the background color changes to yellow or red. (The displayed name will not disappear.)




f.

If both of the V bus main wires are open, ECUs or sensors that are located farther away from the DLC3 than the open part will be displayed as a communication stop on the CAN Bus Check screen.

(In this case, ECU A and B are not displayed or their background color changes to red.)

C240696C04
0.385,3.219 0.906,3.49 0.521,0.271 10 DLC3 5.844,0.083 6.125,0.313 0.281,0.229 10 *a 5.844,0.552 6.125,0.781 0.281,0.229 10 *b 5.469,1.031 5.75,1.26 0.281,0.229 10 *c 5.469,1.542 5.75,1.771 0.281,0.229 10 *d 5.563,2.063 5.844,2.292 0.281,0.229 10 *e 4.302,3.073 4.583,3.302 0.281,0.229 10 *f
*a V Bus *b Sub Bus
*c Terminating Resistor *d Location of malfunction
*e Not displayed or background color is red *f CAN Bus Check screen


HINT:

If a communication error occurs in an ECU, it is not displayed on the CAN Bus Check screen even though the ECU is present.



g.

If both of the sub bus main wires are open, ECUs that are located farther away from the gateway function equipped ECU than the open part will be displayed as a communication stop on the CAN Bus Check screen.

(In this case, ECU I and J are not displayed or their background color changes to red.)

C240697C04
0.385,3.219 0.823,3.438 0.438,0.219 10 DLC3 5.854,0.073 6.146,0.365 0.292,0.292 10 *a 5.583,2.073 5.865,2.302 0.281,0.229 10 *e 5.854,0.542 6.135,0.771 0.281,0.229 10 *b 5.49,1.042 5.771,1.271 0.281,0.229 10 *c 5.49,1.552 5.771,1.781 0.281,0.229 10 *d 4.323,3.063 4.604,3.292 0.281,0.229 10 *f 2.719,1.427 3,1.656 0.281,0.229 10 *g
*a V Bus *b Sub Bus
*c Terminating Resistor *d Location of malfunction
*e Not displayed or background color is red *f CAN Bus Check screen
*g Gateway function equipped ECU - -



h.
C240698C05
0.323,0.083 0.594,0.313 0.271,0.229 10 *a 0.323,2.396 0.594,2.625 0.271,0.229 10 *b 2.885,1.844 3.156,2.073 0.271,0.229 10 *c 0.323,1.833 0.594,2.063 0.271,0.229 10 *c 2.865,4.021 3.135,4.25 0.271,0.229 10 *c
*a When any of the following malfunctions occur on the V bus
*b When any of the following malfunctions occur on a sub bus
*c Not displayed


When any of the following malfunctions occur, CAN communication cannot be established and almost all ECUs and sensors on the bus show a communication error on the CAN Bus Check screen.

Details of Malfunction
Short between CAN wires (CANH and CANL)
Short between a CAN wire (CANH or CANL) and +B
Short between a CAN wire (CANH or CANL) and ground
Open in a CAN main wire

HINT:
·

When a malfunction occurs on the V bus, almost all ECUs and sensors on the V bus and sub bus indicate a communication error (almost all ECUs are not displayed). As communication with the gateway function equipped ECU that is connected to the V bus stops, communication from the ECUs connected to the sub bus that is monitored by the gateway function equipped ECU also stops (these ECUs are not displayed).

·

When a malfunction occurs in a sub bus, almost all ECUs connected to the sub bus indicate a communication error.

·

A communication error in a sub bus does not affect the V bus or other buses.

·

The malfunctioning part can be determined by checking for a short circuit between CAN bus lines or between a CAN bus line and ground or +B short using an electrical tester.





DTC TABLE BY ECU


HINT:
·

In the CAN communication system, the CAN communication DTCs of each ECU can be displayed using the GTS.

·

If CAN communication system DTCs are output, the trouble cannot be determined solely from the DTCs. Perform troubleshooting according to "How to Proceed with Troubleshooting".

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for LHD with VSC)>HOW TO PROCEED WITH TROUBLESHOOTING

·

If system function temporarily returns to normal, DTCs may not be output again even though the following DTC check procedures are used.



a.

BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU) / GTS "ABS/VSC/TRC"

HINT:

DTC communication uses the CAN communication system.


Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
DTC No. Detection Item DTC Detection Condition DTC Detection Precondition DTC Check Procedure Warning Indication in Meter DTC Storage Method
U0073 Control Module Communication Bus Off Either condition is met:
·

The response sent to the brake actuator assembly (skid control ECU) from the spiral with sensor cable sub-assembly (steering angle sensor) is invalid for 1 second or more.

·

The following condition occurs 10 times consecutively within 60 seconds: The response sent to the brake actuator assembly (skid control ECU) from the spiral with sensor cable sub-assembly (steering angle sensor) is invalid at least once within 5 seconds.

·

The brake actuator assembly (skid control ECU) cannot send or receive data (the bus is off) 10 times consecutively.


Both conditions are met:
·

1 second or more elapses after turning the ignition switch to ON.

·

The brake actuator assembly (skid control ECU) power supply voltage is between 10 and 17.4 V.


Turn the ignition switch to ON and wait at least 60 seconds.
·

ABS indicator light illuminates.

·

SLIP indicator light illuminates.


The DTC remains stored until it is cleared using the GTS.
U0100 Lost Communication With ECM/PCM "A" The brake actuator assembly (skid control ECU) is unable to receive certain data from the ECM for 2 seconds or more. All conditions are met:
·

1 second or more elapses after turning the ignition switch to ON.

·

The vehicle speed is 15 km/h (9 mph) or more.

·

The brake actuator assembly (skid control ECU) power supply voltage is between 10 and 17.4 V.


Drive the vehicle for 3 seconds at a speed of 15 km/h (9 mph) or more. SLIP indicator light illuminates. The DTC remains stored until it is cleared using the GTS.
U0124 Lost Communication With Lateral Acceleration Sensor Module Either condition is met:
·

The brake actuator assembly (skid control ECU) is unable to receive certain data from the airbag sensor assembly for 1 second or more.

·

The following condition occurs 10 times or more consecutively within 60 seconds: The brake actuator assembly (skid control ECU) is unable to receive certain data from the airbag sensor assembly at least once within 5 seconds.


Both conditions are met:
·

1 second or more elapses after turning the ignition switch to ON.

·

The brake actuator assembly (skid control ECU) power supply voltage is between 10 and 17.4 V.


Turn the ignition switch to ON and wait at least 60 seconds.
·

ABS indicator light illuminates.

·

SLIP indicator light illuminates.


The DTC remains stored until it is cleared using the GTS.
U0126 Lost Communication With Steering Angle Sensor Module Either condition is met:
·

The brake actuator assembly (skid control ECU) is unable to receive certain data from the spiral with sensor cable sub-assembly (steering angle sensor) for 1 second or more.

·

The following condition occurs 10 times or more consecutively within 60 seconds: The brake actuator assembly (skid control ECU) is unable to receive certain data from the spiral with sensor cable sub-assembly (steering angle sensor) at least once within 5 seconds.


Both conditions are met:
·

1 second or more elapses after turning the ignition switch to ON.

·

The brake actuator assembly (skid control ECU) power supply voltage is between 10 and 17.4 V.


Turn the ignition switch to ON and wait at least 60 seconds. SLIP indicator light illuminates. The DTC remains stored until it is cleared using the GTS.


b.

COMBINATION METER ASSEMBLY / GTS "Combination Meter"

HINT:

DTC communication uses the CAN communication system.


Body Electrical > Combination Meter > Trouble Codes
50001 122
DTC No. Detection Item DTC Detection Condition DTC Check Procedure DTC Check Procedure Warning Indication in Meter DTC Storage Method
U0100 Lost Communication with ECM/PCM "A" The combination meter assembly is unable to receive certain data from the ECM for 2 seconds or more. Both conditions are met:
·

Turning the ignition switch to ON.

·

The voltage at the IG power supply terminal of the combination meter assembly is 11.5 V or higher.


Turn the ignition switch to ON and wait at least 2 seconds. MIL illuminates. The DTC remains stored until it is cleared using the GTS.
U0129 Lost Communication with Brake System Control Module Either condition is met:
·

The combination meter assembly is unable to receive certain data from the brake actuator assembly (skid control ECU) for 2 seconds or more.

·

The combination meter assembly is unable to receive certain data from the brake actuator assembly (skid control ECU) for 3 seconds or more.


Both conditions are met:
·

Turning the ignition switch to ON.

·

The voltage at the IG power supply terminal of the combination meter assembly is 11.5 V or higher.


Turn the ignition switch to ON and wait at least 3 seconds.
·

ABS indicator light illuminates.

·

SLIP indicator light illuminates.

·

Brake warning light illuminates.


The DTC remains stored until it is cleared using the GTS.
U0151 Lost Communication with Restraints Control Module The combination meter assembly is unable to receive certain data from the airbag sensor assembly for 10 seconds or more. Both conditions are met:
·

Turning the ignition switch to ON.

·

The voltage at the IG power supply terminal of the combination meter assembly is 11.5 V or higher.


Turn the ignition switch to ON and wait at least 10 seconds. SRS warning light illuminates. The DTC remains stored until it is cleared using the GTS.


c.

ECM

HINT:

The ECM is connected to the CAN communication system but CAN communication DTCs are not stored.



d.

SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY (STEERING ANGLE SENSOR)

HINT:

The spiral with sensor cable sub-assembly (steering angle sensor) is connected to the CAN communication system but CAN communication DTCs are not stored.



e.

AIRBAG SENSOR ASSEMBLY

HINT:

The airbag sensor assembly is connected to the CAN communication system but CAN communication DTCs are not stored.




CAN BUS WAVEFORMS


C230845E10
4.729,0.25 4.417,0.896 false 4.458,0.875 4.406,0.917 4.406,0.917 4.406,0.865 false 6.625,3.74 5.708,2.635 true 5.729,2.74 5.708,2.635 5.708,2.635 5.781,2.646 false 4.052,3.688 5.052,2.542 true 5.052,2.635 5.063,2.521 5.063,2.521 4.969,2.542 false 2.177,0.688 2.521,0.167 2.521,0.167 2.865,0.167 false 4.396,4.365 4.979,4.365 4.979,4.365 5.51,3.667 false 5.281,3.063 5.844,3.365 0.563,0.302 10 false ECU 3.365,3.063 3.927,3.365 0.563,0.302 10 false ECU 1.698,3.063 2.26,3.365 0.563,0.302 10 false DLC3 1.427,4.781 4.021,5.302 2.594,0.521 10 false : CAN Main Wire (CANH) 1.448,5.229 4.167,5.958 2.719,0.729 10 false : CAN Main Wire (CANL) 1.49,5.823 3.802,6.365 2.313,0.542 10 false : CAN Branch Wire (CANH) 1.5,6.26 3.708,6.688 2.208,0.427 10 false : CAN Branch Wire (CANL) 3.594,4.292 4.563,4.583 0.969,0.292 10 false CAN Branch 2.521,3.719 5.052,4.208 2.531,0.49 10 false Open in CAN Branch Wire (CANL) 5.813,3.802 7.156,4.563 1.344,0.76 10 false Open in CAN Branch Wire (CANH) 4.771,0.156 7.125,0.729 2.354,0.573 10 false Open in CAN Main Bus Wire (CANH) 2.927,0.083 4.146,0.469 1.219,0.385 10 false CAN Main Bus

HINT:
·

This waveform is measured between terminals CANH and GND, and terminals CANL and GND of the DLC3. (Use this as a reference for diagnosis of CAN communication lines.)

·

When malfunctions in multiple ECUs are suspected based on the CAN bus check and DTCs checked using the GTS, check the resistance of the CAN bus using an ohmmeter first. If no problems are found, check the following waveforms.

·

If a waveform is not similar to one of the following 3 patterns (Group 1), then an open in a CAN main wire, an open in a CAN branch wire, or a short between a CAN wire (CANH or CANL) and ground is suspected (Group 2).

·

Wiggle the connector and wire harness to check if the waveform changes.



a.

CAN bus waveforms (Group 1)

i.
C265973N04
0.5,1.5 0.667,1.5 0.667,1.5 0.917,1.167 true 0.5,0.5 0.667,0.5 0.667,0.5 0.906,0.781 true 0.083,0.417 0.698,0.615 0.615,0.198 10 CANH 0.135,1.417 0.75,1.615 0.615,0.198 10 CANL 1.333,1.917 2.865,2.115 1.531,0.198 10 50 μs/DIV. 2.708,0.25 3.427,0.448 0.719,0.198 10 1 V/DIV. 2.958,1.385 3.417,1.583 0.458,0.198 10 GND

Normal waveform


ii.
C265974N03
1.5,1.417 1.667,1.417 1.667,1.417 1.969,1.104 true 1.5,0.5 1.667,0.5 1.667,0.5 1.969,0.792 true 1.052,0.417 1.667,0.615 0.615,0.198 10 CANH 1.135,1.333 1.75,1.531 0.615,0.198 10 CANL 1.333,1.917 2.865,2.115 1.531,0.198 10 50 μs/DIV. 2.969,1.375 3.427,1.573 0.458,0.198 10 GND 2.667,0.24 3.354,0.417 0.688,0.177 10 1 V/DIV.

Open in both of the lines (CANH and CANL) of a CAN branch

HINT:
·

Waveforms (waveforms shown using dotted lines) are not output from an ECU or sensor connected to a CAN branch with an open circuit in both lines. (Waveforms from other ECUs or sensors are normal.)

·

Because this waveform is similar to a normal waveform, instead of using the waveform, the malfunctioning part can be narrowed down by performing a CAN bus check.




iii.
C265975N03
0.5,1.333 0.75,1.333 0.75,1.333 1.063,0.969 true 1.292,0.917 0.729,0.583 0.729,0.583 0.5,0.583 true 0.083,0.5 0.698,0.698 0.615,0.198 10 CANH 0.135,1.25 0.75,1.448 0.615,0.198 10 CANL 1.344,1.917 2.875,2.115 1.531,0.198 10 50 μs/DIV. 2.729,0.271 3.354,0.479 0.625,0.208 10 1 V/DIV. 2.938,1.385 3.396,1.583 0.458,0.198 10 GND

Short between the CAN bus lines (CANH and CANL)

HINT:
·

Waveforms disappear.

·

If the malfunction is in an ECU, disconnecting the ECU will change the waveform. If the waveform does not change, a malfunction in the wire harness is suspected.





b.

CAN bus waveforms (reference) (Group 2)

NOTICE:

The following CAN bus waveforms can be used only as reference. The actual measured waveform may differ significantly depending on the location of the open or short circuit.


i.
C265976N03
0.938,0.76 0.667,0.5 0.667,0.5 0.5,0.5 true 0.5,1.5 0.667,1.5 0.667,1.5 0.844,1.167 true 0.083,0.417 0.698,0.615 0.615,0.198 10 CANH 0.135,1.417 0.75,1.615 0.615,0.198 10 CANL 1.313,1.927 2.844,2.125 1.531,0.198 10 50 μs/DIV. 2.708,0.281 3.344,0.5 0.635,0.219 10 1 V/DIV. 2.969,1.385 3.427,1.583 0.458,0.198 10 GND

Open in a CAN branch wire (CANH)

HINT:
·

An abnormal waveform is output from an ECU with an open in one of its CAN branch wires. Because this abnormal output interferes with the signals from other ECUs, the output of other ECUs will also appear abnormal.

·

Narrow down the malfunctioning part by checking DTCs or performing a CAN bus check, or by checking waveform changes when ECUs or sensors are disconnected. The waveform will change to one for an open in both sides of a CAN branch when the ECU or sensor with an open CAN branch wire is disconnected.




ii.
C265977N03
0.5,1.417 0.667,1.417 0.667,1.417 0.906,1.146 true 0.5,0.5 0.667,0.5 0.667,0.5 0.833,0.74 true 0.083,0.417 0.698,0.615 0.615,0.198 10 CANH 0.135,1.344 0.75,1.542 0.615,0.198 10 CANL 1.313,1.917 2.844,2.115 1.531,0.198 10 50 μs/DIV. 2.698,0.281 3.417,0.51 0.719,0.229 10 1 V/DIV. 2.958,1.385 3.417,1.583 0.458,0.198 10 GND

Open in a CAN branch wire (CANL)

HINT:
·

An abnormal waveform is output from an ECU with an open in one of its CAN branch wires. Because this abnormal output interferes with the signals from other ECUs, the output of other ECUs will also appear abnormal.

·

Narrow down the malfunctioning part by checking DTCs or performing a CAN bus check, or by checking waveform changes when ECUs or sensors are disconnected. The waveform will change to one for an open in both sides of a CAN branch when the ECU or sensor with an open CAN branch wire is disconnected.




iii.
C265978N03
0.5,0.5 0.667,0.5 0.667,0.5 0.938,0.708 true 0.5,1.417 0.75,1.417 0.75,1.417 0.938,1.156 true 0.083,0.417 0.698,0.615 0.615,0.198 10 CANH 0.135,1.333 0.75,1.531 0.615,0.198 10 CANL 1.323,1.927 2.854,2.125 1.531,0.198 10 50 μs/DIV. 2.698,0.281 3.281,0.521 0.583,0.24 10 1 V/DIV. 2.969,1.375 3.427,1.573 0.458,0.198 10 GND

Open in a CAN main wire (CANH)

HINT:
·

Waveforms of ECUs or sensors that are closer to the DLC3 than the open part are almost normal.

·

Waveforms of ECUs or sensors that are on the opposite side of the DLC3 from the open part are abnormal.

·

An open in a CAN main wire can be confirmed by measuring the resistance between the CANH and CANL terminals of any CAN branch.




iv.
C265979N03
0.5,1.75 0.75,1.75 0.75,1.75 1.083,1.531 true 1.063,1.333 0.75,0.917 0.75,0.917 0.5,0.917 true 0.083,0.833 0.698,1.031 0.615,0.198 10 CANH 0.083,1.667 0.698,1.865 0.615,0.198 10 CANL 1.313,1.917 2.844,2.115 1.531,0.198 10 50 μs/DIV. 2.719,0.302 3.375,0.552 0.656,0.25 10 1 V/DIV. 2.969,1.375 3.427,1.573 0.458,0.198 10 GND

Short between a CAN bus line (CANH) and ground

HINT:
·

Narrow down the shorted part by checking for waveform changes when disconnecting connector(s) from the CAN junction connector(s) or when disconnecting ECUs or sensors.

·

A short to ground in the CANH line can be confirmed by measuring the resistance between CANH and ground using an ohmmeter.




v.
C265980N03
0.5,1.583 0.667,1.583 0.667,1.583 0.833,1.385 true 0.5,0.5 0.667,0.5 0.667,0.5 1.021,0.708 true 0.083,0.417 0.698,0.615 0.615,0.198 10 CANH 0.135,1.5 0.75,1.698 0.615,0.198 10 CANL 1.333,1.917 2.865,2.115 1.531,0.198 10 50 μs/DIV. 2.698,0.271 3.292,0.531 0.594,0.26 10 1 V/DIV. 2.969,1.375 3.427,1.573 0.458,0.198 10 GND

Short between a CAN bus line (CANL) and ground

HINT:
·

Narrow down the shorted part by checking for waveform changes when disconnecting connector(s) from the CAN junction connector(s) or when disconnecting ECUs or sensors.

·

A short to ground in the CANL line can be confirmed by measuring the resistance between CANL and ground using an ohmmeter.






DATA SENDING/RECEIVING TABLE


a.

Data sending/receiving table

HINT:

If Data List items related to sent/received data are not displayed properly, the part for which communication is interrupted can be determined using the table below.


Data content Data Detected and Sent by Data Received from
(Can be Checked in Data List)
Data Received
(Cannot be Checked in Data List)
Selected System Relevant Data List Item Link

*: The combination meter assembly receives a vehicle speed signal from the brake actuator assembly (skid control ECU) and sends the signal to other ECUs.

Engine speed ECM Combination meter assembly
·

Airbag sensor assembly

·

Brake actuator assembly (skid control ECU)


Engine and ECT (for 1VD-FTV) Engine Speed (Click here)
Engine and ECT (for 1VD-FTV [w/o EGR System]) Engine Speed (Click here)
Engine and ECT (for 1VD-FTV [w/ DPF]) Engine Speed (Click here)
Engine and ECT (for 1GR-FE) Engine Speed (Click here)
Combination Meter Engine Rpm (Click here)
Engine coolant temperature ECM Combination meter assembly Brake actuator assembly (skid control ECU) Engine and ECT (for 1VD-FTV) Coolant Temp (Click here)
Engine and ECT (for 1VD-FTV [w/o EGR System]) Coolant Temp (Click here)
Engine and ECT (for 1VD-FTV [w/ DPF]) Coolant Temp (Click here)
Engine and ECT (for 1GR-FE) Coolant Temp (Click here)
Combination Meter Coolant Temperature (Click here)
Stop light switch ECM - Airbag sensor assembly Engine and ECT (for 1VD-FTV) Stop Light Switch (Click here)
Engine and ECT (for 1VD-FTV [w/o EGR System]) Stop Light Switch (Click here)
Engine and ECT (for 1VD-FTV [w/ DPF]) Stop Light Switch (Click here)
Engine and ECT (for 1GR-FE) Stop Light Switch (Click here)
Brake actuator assembly (skid control ECU) - Airbag sensor assembly ABS/VSC/TRC Stop Light SW (Click here)
Vehicle speed Brake actuator assembly (skid control ECU)
·

ECM

·

Combination meter assembly


Airbag sensor assembly ABS/VSC/TRC Vehicle Speed (Click here)
Engine and ECT (for 1VD-FTV) Vehicle Speed (Click here)
Engine and ECT (for 1VD-FTV [w/o EGR System]) Vehicle Speed (Click here)
Engine and ECT (for 1VD-FTV [w/ DPF]) Vehicle Speed (Click here)
Engine and ECT (for 1GR-FE) Vehicle Speed (Click here)
Combination Meter Vehicle Speed Meter (Click here)
Combination meter assembly* - Airbag sensor assembly Combination Meter Vehicle Speed Meter (Click here)