Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (for LHD with VSC) › from 2022.09
RM25T0E _57 Power Source / Network _057931 NETWORKING _0306321 CAN COMMUNICATION SYSTEM(for LHD with VSC) J

NETWORKING  CAN COMMUNICATION SYSTEM(for LHD with VSC)  Short in CAN Bus Lines  


DESCRIPTION

There may be a short circuit between the CAN bus lines when the resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is below 53 Ω.

Symptom Trouble Area
The resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is below 53 Ω.
·

Short between CAN bus lines

·

ECM

·

Brake actuator assembly (skid control ECU)

·

Spiral with sensor cable sub-assembly (steering angle sensor)

·

Airbag sensor assembly

·

Combination meter assembly

·

No. 6 CAN junction connector

·

DLC3 CAN branch wire or connector



WIRING DIAGRAM

C371327E02
4.052,0.542 4.667,0.74 0.615,0.198 10 false I119 4.042,1.052 4.656,1.25 0.615,0.198 10 false I119 4.115,0.313 4.729,0.51 0.615,0.198 10 false 1 4.115,0.833 4.729,1.031 0.615,0.198 10 false 2 5.271,1.344 5.885,1.542 0.615,0.198 10 false L26 5.271,1.5 7.083,1.875 1.813,0.375 10 false Combination Meter Assembly 6.104,1.177 6.719,1.375 0.615,0.198 10 false CANL 6.115,0.438 6.729,0.635 0.615,0.198 10 false CANH 5.833,0.438 6.448,0.635 0.615,0.198 10 false 13 5.833,0.958 6.448,1.156 0.615,0.198 10 false 14 2.896,0.542 3.51,0.74 0.615,0.198 10 false I120 2.885,1.063 3.5,1.26 0.615,0.198 10 false I120 2.979,0.823 3.594,1.021 0.615,0.198 10 false 2 2.979,0.292 3.594,0.49 0.615,0.198 10 false 1 0.448,1.448 1.063,1.646 0.615,0.198 10 false I17 0.458,1.615 1.073,1.813 0.615,0.198 10 false DLC3 0.708,1.042 1.323,1.24 0.615,0.198 10 false CANL 0.698,0.542 1.313,0.74 0.615,0.198 10 false CANH 1.188,0.438 1.802,0.635 0.615,0.198 10 false 6 1.177,0.938 1.792,1.135 0.615,0.198 10 false 14 4.042,2.479 4.656,2.677 0.615,0.198 10 false I121 4.042,2.99 4.656,3.188 0.615,0.198 10 false I121 4.125,2.771 4.74,2.969 0.615,0.198 10 false 2 4.125,2.25 4.74,2.448 0.615,0.198 10 false 1 4.635,3.271 5.25,3.469 0.615,0.198 10 false L47 4.625,3.417 7.073,3.938 2.448,0.521 10 false Spiral with Sensor Cable Sub-assembly (Steering Angle Sensor) 6.125,2.49 6.74,2.688 0.615,0.198 10 false CANH 6.135,3 6.75,3.198 0.615,0.198 10 false CANL 5.917,2.875 6.531,3.073 0.615,0.198 10 false 3 5.917,2.385 6.531,2.583 0.615,0.198 10 false 4 4.042,4.698 4.656,4.896 0.615,0.198 10 false I122 4.042,5.219 4.656,5.417 0.615,0.198 10 false I122 4.135,4.99 4.75,5.188 0.615,0.198 10 false 2 4.125,4.458 4.74,4.656 0.615,0.198 10 false 1 6.115,5.625 7.01,5.844 0.896,0.219 10 false I84 6.115,5.792 6.844,6.073 0.729,0.281 10 false ECM 6.146,4.563 6.76,4.76 0.615,0.198 10 false CANH 6.146,5.323 6.76,5.521 0.615,0.198 10 false CANL 5.854,5.094 6.469,5.292 0.615,0.198 10 false 49 5.865,4.573 6.479,4.771 0.615,0.198 10 false 41 2.885,5.229 3.5,5.427 0.615,0.198 10 false I123 2.896,4.698 3.51,4.896 0.615,0.198 10 false I123 2.979,4.99 3.594,5.188 0.615,0.198 10 false 2 2.979,4.448 3.594,4.646 0.615,0.198 10 false 1 0.24,5.625 0.854,5.823 0.615,0.198 10 false I51 0.229,5.781 1.854,6.208 1.625,0.427 10 false Airbag Sensor Assembly 0.708,5.229 1.323,5.427 0.615,0.198 10 false CANL 0.688,4.698 1.302,4.896 0.615,0.198 10 false CANH 1.219,5.115 1.833,5.313 0.615,0.198 10 false 22 1.198,4.594 1.813,4.792 0.615,0.198 10 false 13 0.177,3.458 0.792,3.656 0.615,0.198 10 false A42 0.167,3.625 1.813,4.073 1.646,0.448 10 false Brake Actuator Assembly (Skid Control ECU) 0.688,2.479 1.302,2.677 0.615,0.198 10 false CANH 0.698,2.99 1.313,3.188 0.615,0.198 10 false CANL 1.198,2.375 1.813,2.573 0.615,0.198 10 false 22 1.198,2.875 1.813,3.073 0.615,0.198 10 false 10 2.875,3 3.49,3.198 0.615,0.198 10 false I124 2.885,2.479 3.5,2.677 0.615,0.198 10 false I124 2.99,2.781 3.604,2.979 0.615,0.198 10 false 2 2.969,2.25 3.583,2.448 0.615,0.198 10 false 1 2.823,5.646 4.76,5.99 1.938,0.344 10 false No. 6 CAN Junction Connector

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for LHD with VSC)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

When disconnecting and reconnecting the battery.

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

The vehicle is equipped with an SRS (Supplemental Restraint System) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the Precaution in the SRS.

·

When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the infomation stored in it will not match the infomation from the vehicle and a DTC may be stored.



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.

·

Connectors that connect to the CAN junction connector can be distinguished by the color of their CAN bus lines. When the connectors have been disconnected from the CAN junction connector, reconnecting the connectors to non-original positions on the CAN junction connector does not affect system performance. However, it is preferred to reconnect the connectors to their original positions to avoid negative effects on the wiring such as tension on the wiring harnesses, and to make future maintenance easier.



PROCEDURE

1.CHECK FOR SHORT IN CAN BUS WIRES (NO. 6 CAN JUNCTION CONNECTOR)
a.

Disconnect the No. 6 CAN junction connectors.

C371325C03
5.26,2.813 5.5,2.5 5.5,2.5 5.667,2.5 true 5.271,2.99 5.594,3.26 5.594,3.26 5.76,3.26 true 4.198,2.219 4.51,2.417 0.313,0.198 10 false *a 0.094,0.052 0.406,0.25 0.313,0.198 10 false *1 2.031,2.198 2.344,2.396 0.313,0.198 10 false I119 2.042,2.417 2.354,2.615 0.313,0.198 10 false I120 2.031,3.313 2.344,3.51 0.313,0.198 10 false I124 2.042,3.094 2.448,3.313 0.406,0.219 10 false I123 2.052,2.875 2.427,3.073 0.375,0.198 10 false I122 2.031,2.646 2.417,2.854 0.385,0.208 10 false I121 5.708,2.417 6.292,2.635 0.583,0.219 10 false CANH 5.802,3.188 6.385,3.406 0.583,0.219 10 false CANL
*1 No. 6 CAN Junction Connector - -
*a Rear view of wire harness connector
(to No. 6 CAN Junction Connector)
- -


No. 6 CAN Junction Connector Wiring Color Connect to
I119-1 (CANH) G Combination meter assembly
I119-2 (CANL) W
I120-1 (CANH) L DLC3
I120-2 (CANL) W
I121-1 (CANH) R Spiral with sensor cable sub-assembly (steering angle sensor)
I121-2 (CANL) W
I122-1 (CANH) G ECM
I122-2 (CANL) W
I123-1 (CANH) P Airbag sensor assembly
I123-2 (CANL) W
I124-1 (CANH) B Brake actuator assembly (skid control ECU)
I124-2 (CANL) W


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connect to
I119-1 (CANH) - I119-2 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω Combination meter assembly
I120-1 (CANH) - I120-2 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher DLC3
I121-1 (CANH) - I121-2 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Spiral with sensor cable sub-assembly (steering angle sensor)
I122-1 (CANH) - I122-2 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω ECM
I123-1 (CANH) - I123-2 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Airbag sensor assembly
I124-1 (CANH) - I124-2 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Brake actuator assembly (skid control ECU)



Result:
Result Proceed to
OK A
NG (to Combination meter assembly CAN main wire) B
NG (to ECM CAN main wire) C
NG (to DLC3 CAN branch wires) D
NG (ECU or sensor CAN branch wires) E



A

REPLACE NO. 6 CAN JUNCTION CONNECTOR

B

2.CONNECT CONNECTOR

C

4.CONNECT CONNECTOR

D

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO DLC3 (CANH, CANL)

E

6.CHECK FOR SHORT IN CAN BUS WIRES (ECU, SENSOR)
2.CONNECT CONNECTOR
a.

Reconnect the No. 6 CAN junction connectors.


Result:
Proceed to
NEXT



NEXT

3.CHECK FOR SHORT IN CAN BUS WIRES (COMBINATION METER ASSEMBLY)
3.CHECK FOR SHORT IN CAN BUS WIRES (COMBINATION METER ASSEMBLY)
a.
C363466C01
1.385,0.271 1.99,0.552 0.604,0.281 0.427,1.875 0.563,1.875 0.563,1.875 0.781,1.646 true 0.656,2.052 0.792,2.052 0.792,2.052 0.938,1.656 true 0.167,0.135 0.479,0.292 0.313,0.156 10 false *a 1.521,0.281 1.833,0.438 0.313,0.156 10 false L26 0.031,1.75 0.469,1.938 0.438,0.188 10 false CANH 0.26,1.958 0.698,2.146 0.438,0.188 10 false CANL
*a Front view of wire harness connector
(to Combination Meter Assembly)


Disconnect the combination meter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L26-13 (CANH) - L26-14 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO COMBINATION METER ASSEMBLY (COMBINATION METER ASSEMBLY - NO. 6 CAN JUNCTION CONNECTOR)

4.CONNECT CONNECTOR
a.

Reconnect the No. 6 CAN junction connectors.


Result:
Proceed to
NEXT



NEXT

5.CHECK FOR SHORT IN CAN BUS WIRES (ECM)
5.CHECK FOR SHORT IN CAN BUS WIRES (ECM)
a.
C363469C02
1.49,0.292 1.948,0.521 0.458,0.229 2.427,1.354 2.656,1.167 2.656,1.167 2.823,1.167 true 2.427,1.458 2.625,1.938 2.625,1.938 2.792,1.938 true 0.135,0.094 0.448,0.25 0.313,0.156 10 false *a 2.875,1.042 3.385,1.292 0.51,0.25 10 false CANH 2.833,1.823 3.344,2.073 0.51,0.25 10 false CANL 1.625,0.333 2.135,0.583 0.51,0.25 10 false I84
*a Front view of wire harness connector
(to ECM)


Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I84-41 (CANH) - I84-49 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO ECM (ECM - NO. 6 CAN JUNCTION CONNECTOR)

6.CHECK FOR SHORT IN CAN BUS WIRES (ECU, SENSOR)
a.
C300827C55
0.115,0.99 0.521,1.25 0.406,0.26 1.938,0.906 1.563,0.458 1.563,0.458 1.417,0.458 true 1.958,1.458 2.354,1.885 2.354,1.885 2.469,1.885 true 0.135,0.115 0.448,0.271 0.313,0.156 10 false *a 0.198,1.021 0.479,1.188 0.281,0.167 10 false I17 1,0.333 1.49,0.479 0.49,0.146 10 false CANH 2.563,1.75 3.177,1.948 0.615,0.198 10 false CANL
*a Front view of DLC3


Reconnect the CAN junction connector.


b.

Disconnect the connector that includes terminals CANH and CANL from the ECU or sensor to which the short circuited CAN branch wire is connected.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I17-6 (CANH) - I17-14 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω


HINT:

If the resistance becomes normal (between 54 and 69 Ω) when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.



Result:
Proceed to
OK
NG



OK

REPLACE CORRESPONDING ECU OR SENSOR

NG

REPAIR OR REPLACE CORRESPONDING ECU OR SENSOR CAN BRANCH WIRES OR CONNECTOR