Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ DPF) › from 2022.09
RM25T0E _51 Engine / Hybrid System _029760 1VD-FTV ENGINE CONTROL _0282525 ECD SYSTEM(w/ DPF) C

1VD-FTV ENGINE CONTROL  ECD SYSTEM(w/ DPF)  P0560  System Voltage  


DESCRIPTION

The battery supplies electricity to the ECM even when the ignition switch is in the OFF position. This power allows the ECM to store data such as DTC history, freeze frame data and fuel trim values. If the battery voltage falls below a minimum level, the ECM memory is cleared and the ECM determines that there is a malfunction in the power supply circuit. When the engine is next started, the ECM illuminates the MIL and sets the DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0560 System Voltage Open in ECM back up power source circuit
(1 trip detection logic)
·

Open in back up power source circuit

·

Battery

·

Battery terminals

·

EFI MAIN fuse

·

ECM


Comes on DTC stored

HINT:

If DTC P0560 is set, the ECM does not store other DTCs or the data stored in the ECM is partly erased.


CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P0560 Engine switch on (IG) for 3 seconds

WIRING DIAGRAM

for RHD
A118508E57
0.917,1.969 2.073,2.177 1.156,0.208 10 false Battery 1.906,0.708 2.479,0.854 0.573,0.146 10 false FL MAIN 3.573,0.708 4.25,0.854 0.677,0.146 10 false EFI MAIN 6.042,2.583 6.375,2.74 0.333,0.156 10 false ECM 5.833,0.885 6.25,1.042 0.417,0.156 10 false BATT 5.563,0.708 5.75,0.865 0.188,0.156 10 false 20 5.552,1.281 5.74,1.438 0.188,0.156 10 false 81 5.5,0.885 5.813,1.073 0.313,0.188 10 false A29 5.5,1.479 5.792,1.667 0.292,0.188 10 false C39 5.833,1.479 6.031,1.667 0.198,0.188 10 false E1 3.677,1.021 3.823,1.198 0.146,0.177 10 false 1 4.01,1.021 4.156,1.198 0.146,0.177 10 false 2

for LHD
A118508E56
0.917,1.969 2.531,2.156 1.615,0.188 10 false Battery 1.906,0.708 2.479,0.854 0.573,0.146 10 false FL MAIN 3.573,0.708 4.25,0.854 0.677,0.146 10 false EFI MAIN 6.042,2.583 6.375,2.74 0.333,0.156 10 false ECM 5.833,0.885 6.25,1.042 0.417,0.156 10 false BATT 5.563,0.708 5.75,0.865 0.188,0.156 10 false 20 5.552,1.281 5.74,1.438 0.188,0.156 10 false 81 5.531,0.896 5.844,1.083 0.313,0.188 10 false I84 5.5,1.479 5.792,1.667 0.292,0.188 10 false C39 5.833,1.479 6.031,1.667 0.198,0.188 10 false E1 3.677,1.021 3.823,1.198 0.146,0.177 10 false 1 4.01,1.021 4.156,1.198 0.146,0.177 10 false 2

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (ECM - EFI MAIN FUSE, EFI MAIN FUSE - BATTERY)
a.

Check the harness and connector between the EFI MAIN fuse and ECM.

i.

Remove the EFI MAIN fuse from the fuse block assembly.


ii.

Disconnect the ECM connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
for RHD
Tester Connection Condition Specified Condition
EFI MAIN fuse terminal 2 - A29-20 (BATT) Always Below 1 Ω
EFI MAIN fuse terminal 2 or A29-20 (BATT) - Body ground Always 10 kΩ or higher


Standard resistance:
for LHD
Tester Connection Condition Specified Condition
EFI MAIN fuse terminal 2 - I84-20 (BATT) Always Below 1 Ω
EFI MAIN fuse terminal 2 or I84-20 (BATT) - Body ground Always 10 kΩ or higher




b.

Check the harness and connector between the EFI MAIN fuse and battery.

i.

Remove the EFI MAIN fuse from the fuse block assembly.


ii.

Disconnect the positive battery terminal.


iii.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
Battery positive (+) terminal - EFI MAIN fuse terminal 1 Always Below 1 Ω
Battery positive (+) terminal or EFI MAIN fuse terminal 1 - Body ground Always 10 kΩ or higher




Result:
Proceed to
OK
NG



OK

2.INSPECT BATTERY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT BATTERY
a.

Check that the battery is not depleted.

OK:

Battery is not depleted.



Result:
Proceed to
OK
NG



OK

3.CHECK BATTERY TERMINAL

NG

REPLACE BATTERY

3.CHECK BATTERY TERMINAL
a.

Check that the battery terminals are not loose or corroded.

OK:

Battery terminals are not loose or corroded.



Result:
Proceed to
OK
NG



OK

4.CHECK WHETHER DTC OUTPUT RECURS

NG

REPAIR OR REPLACE BATTERY TERMINAL

4.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 234

d.

Turn the ignition switch off and turn the GTS off.


e.

Start the engine and turn the GTS on.


f.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 234

g.

Read DTCs.

Result:
Display (DTC Output) Proceed to
P0560 is output A
No DTC is output B




A

B