The mass air flow meter sub-assembly consists of a platinum hot wire, a temperature sensor and a control circuit installed in a plastic housing. The temperature sensor (located in the intake air by-pass of the housing) detects the intake air temperature.
There is little variation in the output from the mass air flow meter, as the output voltage is converted into a periodic signal which minimizes the effect of wire harness resistance.
The internal circuit of the mass air flow meter sub-assembly contains a hot wire and cold wire. A voltage is output through a bridge circuit (refer to the illustration) indicating the cooling of the hot wire according to the intake air amount. This voltage is then converted into a periodic signal by the periodic signal conversion circuit and output to the ECM. The frequency varies between approximately 250 to 11000 Hz depending on the air flow rate. The ECM calculates the mass air flow rate based on this frequency.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P0100 | Mass or Volume Air Flow Circuit | Mass air flow meter signal frequency is less than 850 Hz with the engine speed at 400 rpm or more for 3 seconds. (1 trip detection logic) |
·
Open or short in mass air flow meter sub-assembly circuit
·
Mass air flow meter sub-assembly
·
ECM |
Comes on | DTC stored |
| DTC No. | Data List |
|---|---|
| P0100 | MAF |
There is less air than the actual intake air amount, EGR is decreased according to the target EGR:
- Combustion noise worsens
| DTC No. | DTC Detection Drive Pattern |
|---|---|
| P0100 | 3 seconds after engine is started |
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION) and initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>INITIALIZATION).
After replacing the fuel supply pump assembly, the ECM needs initialization.
Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>INITIALIZATION
After replacing an fuel injector, the ECM needs registration.
Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
| *a | Front view of wire harness connector (to Mass Air Flow Meter Sub-assembly) |
Disconnect the mass air flow meter sub-assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| C41-3 (+B) - Body ground | Ignition switch ON | 11 to 14 V |
| Proceed to |
| OK |
| NG |
OK
NG
Disconnect the mass air flow meter sub-assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C41-1 (VG) - C39-71 (VG) | Always | Below 1 Ω |
| C41-2 (E2G) - C39-94 (EVG) | Always | Below 1 Ω |
| C41-1 (VG) or C39-71 (VG) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
| OK |
| NG |
OK
NG
Replace the mass air flow meter sub-assembly.
Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>MASS AIR FLOW METER(w/ DPF)>REMOVAL
| Proceed to |
| NEXT |
NEXT
Connect the GTS to the DLC3.
Clear the DTCs.
Start the engine and wait for 3 seconds or more.
Enter the following menus: Engine and ECT / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
| P0100 is output | A |
| No DTC is output | B |
A
B
Replace the ECM.
Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECM>REMOVAL
| Proceed to |
| NEXT |
NEXT
Connect the GTS to the DLC3.
Clear the DTCs.
Start the engine and wait for 3 seconds or more.
Enter the following menus: Engine and ECT / Trouble Codes.
Confirm that the DTC is not output again.
| Proceed to |
| NEXT |
NEXT
Repair or replace the harness or connector.
| Proceed to |
| NEXT |
NEXT
Disconnect the mass air flow meter sub-assembly connector.
Remove the MAIN2 relay from the engine room relay block assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C41-3 (+B) - MAIN2 relay terminal 3 | Always | Below 1 Ω |
| C41-3 (+B) or MAIN2 relay terminal 3 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
| OK |
| NG |
OK
NG
Inspect the MAIN2 relay.
Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>RELAY>ON-VEHICLE INSPECTION
| Proceed to |
| OK |
| NG |
OK
NG
Remove the MAIN2 relay from the engine room relay block assembly.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| MAIN2 relay terminal 1 - A29-44 (MREL) | Always | Below 1 Ω |
| MAIN2 relay terminal 1 - A29-44 (MREL) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| MAIN2 relay terminal 1 - I84-44 (MREL) | Always | Below 1 Ω |
| MAIN2 relay terminal 1 - I84-44 (MREL) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
| OK |
| NG |
OK
Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>ECM Power Source Circuit
NG
Replace the MAIN2 relay.
| Proceed to |
| NEXT |
NEXT