The fuel temperature sensor monitors the fuel temperature. The fuel temperature sensor has a thermistor that varies its resistance depending on the fuel temperature. When the fuel temperature is low, the resistance of the thermistor is high. When the temperature is high, the resistance is low. The variations of resistance are communicated to the ECM as changes of voltage (see Fig. 1).
The fuel temperature sensor is connected to the ECM. The 5 V power source voltage in the ECM is applied to the fuel temperature sensor from terminal THF via resistor R.
The resistor R and fuel temperature sensor are connected in series. When the resistance value of the fuel temperature sensor changes due to a change of fuel temperature, the voltage at terminal THF also changes. Based on this signal, the ECM corrects the pressure control compensation of the fuel supply pump and determines if there are errors.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P0180 | Fuel Temperature Sensor "A" Circuit | Open or short in fuel temperature sensor circuit for 0.5 seconds (1 trip detection logic) |
·
Open or short in fuel temperature sensor circuit
·
Fuel temperature sensor
·
Fuel temperature sensor, suction control valve wire
·
ECM |
Comes on | DTC stored |
| P0182 | Fuel Temperature Sensor "A" Circuit Low Input | Short in fuel temperature sensor circuit for 0.5 seconds (1 trip detection logic) |
·
Short in fuel temperature sensor circuit
·
Fuel temperature sensor
·
Fuel temperature sensor, suction control valve wire
·
ECM |
Comes on | DTC stored |
| P0183 | Fuel Temperature Sensor "A" Circuit High Input | Open in fuel temperature sensor circuit for 0.5 seconds (1 trip detection logic) |
·
Open in fuel temperature sensor circuit
·
Fuel temperature sensor
·
Fuel temperature sensor, suction control valve wire
·
ECM |
Comes on | DTC stored |
| DTC No. | DTC Detection Drive Pattern |
|---|---|
| P0180 P0182 P0183 |
Ignition switch to ON for 0.5 seconds |
After replacing the ECM, the new ECM needs registration (See pageEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION) and initialization (See pageEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>INITIALIZATION).
If DTCs relating to different systems are output, and they share terminal E2 as their ground, check this ground circuit first.
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Fuel Temperature.
| Tester Display |
|---|
| Fuel Temperature |
Read the value.
Same value as the actual fuel temperature
| Result | Proceed to |
|---|---|
| -40°C (-40°F) | A |
| 140°C (284°F) or higher | B |
| OK (Same as actual fuel temperature) | C |
If there is an open circuit, the GTS indicates -40°C (-40°F).
If there is a short circuit, the GTS indicates 140°C (284°F) or more.
A
B
C
Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>CHECK FOR INTERMITTENT PROBLEMS
| *A | for RHD |
| *B | for LHD |
| *1 | Fuel Temperature Sensor, Suction Control Valve |
| *2 | ECM |
| *a | Front view of wire harness connector (to Fuel Temperature Sensor, Suction Control Valve) |
Disconnect the fuel temperature sensor, suction control valve connector.
Connect terminals 2 (THF) and 1 (E2) of the fuel temperature sensor, suction control valve wire harness side connector.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT /Data List / Fuel Temperature.
| Tester Display |
|---|
| Fuel Temperature |
Read the value.
140°C (284°F) or higher
| Proceed to |
| OK |
| NG |
OK
NG
| *A | for RHD |
| *B | for LHD |
| *a | Component without harness connected (Fuel Temperature Sensor, Suction Control Valve Wire) |
Remove the fuel temperature sensor, suction control valve wire.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| r3-1 - rC2-4 (E2) | Always | Below 1 Ω |
| r3-2 - rC2-3 (THF) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| r3-1 - rC1-4 (E2) | Always | Below 1 Ω |
| r3-2 - rC1-3 (THF) | Always | Below 1 Ω |
| Proceed to |
| OK |
| NG |
OK
NG
| *A | for RHD |
| *B | for LHD |
| *a | Front view of wire harness connector (to Fuel Temperature Sensor, Suction Control Valve) |
| *b | Front view of wire harness connector (to ECM) |
Disconnect the fuel temperature sensor, suction control valve connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| rC2-2 (THF) - C39-116 (THF) | Always | Below 1 Ω |
| rC2-4 (E2) -C39-92 (E2) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| rC1-2 (THF) - C39-116 (THF) | Always | Below 1 Ω |
| rC1-4 (E2) -C39-92 (E2) | Always | Below 1 Ω |
| Proceed to |
| OK |
| NG |
OK
NG
| *1 | Fuel Temperature Sensor, Suction Control Valve |
| *2 | ECM |
Disconnect the fuel temperature sensor, suction control valve connector.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Fuel Temperature.
| Tester Display |
|---|
| Fuel Temperature |
Read the value.
-40°C (-40°F)
| Proceed to |
| OK |
| NG |
OK
NG
| *A | for RHD |
| *B | for LHD |
| *a | Component without harness connected (Fuel Temperature Sensor, Suction Control Valve Wire) |
| *b | Fuel Temperature Sensor Wire "A" |
| *c | Fuel Temperature Sensor, Suction Control Valve Wire "B" |
Remove the fuel temperature sensor, suction control valve wire.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| r3-2 or rC2-3 (THF) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| r3-2 or rC1-3 (THF) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
| OK |
| NG |
OK
NG
| *A | for RHD |
| *B | for LHD |
| *a | Front view of wire harness connector (to Fuel Temperature Sensor, Suction Control Valve) |
| *b | Front view of wire harness connector (to ECM) |
Disconnect the fuel temperature sensor, suction control valve connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| rC2-3 (THF) or C39-116 (THF) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| rC1-3 (THF) or C39-116 (THF) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
| OK |
| NG |
OK
NG