The EGR valve position sensor is mounted on the electric EGR control valve assembly and used for detecting the EGR valve angle. The EGR valve angle detected by the sensor is sent to the ECM as feedback. The ECM then regulates the EGR valve angle in accordance with engine running conditions.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P0405 | Exhaust Gas Recirculation Sensor "A" Circuit Low | EGR valve position sensor output voltage is less than 0.2 V for 2 seconds. (1 trip detection logic) |
·
Open or short in EGR valve position sensor circuit
·
Electric EGR control valve assembly (EGR valve position sensor)
·
ECM |
Comes on | DTC stored |
| P0406 | Exhaust Gas Recirculation Sensor "A" Circuit High | EGR valve position sensor output voltage is higher than 4.8 V for 2 seconds. (1 trip detection logic) |
·
Open or short in EGR valve position sensor circuit
·
Electric EGR control valve assembly (EGR valve position sensor)
·
ECM |
Comes on | DTC stored |
| DTC No. | DTC Detection Drive Pattern |
|---|---|
| P0405 | Ignition switch ON for 2 seconds or more |
| P0406 |
When the output voltage of the EGR valve position sensor deviates from the normal operating range of 0.2 to 4.8 V for more than 2 seconds, the ECM interprets this as a malfunction of the sensor circuit and illuminates the MIL.
After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION) and initialization (Click here Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>INITIALIZATION).
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Disconnect the electric EGR control valve assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C106-3 (VC) - C39-120 (VCEG) | Always | Below 1 Ω |
| C106-2 (VTA) - A29-59 (EGRA) | Always | Below 1 Ω |
| C160-1 (E2) - C39-97 (EEGL) | Always | Below 1 Ω |
| C106-3 (VC) or C39-120 (VCEG) - Body ground | Always | 10 kΩ or higher |
| C106-2 (VTA) or C39-59 (EGRA) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C106-3 (VC) - C39-120 (VCEG) | Always | Below 1 Ω |
| C106-2 (VTA) - I84-59 (EGRA) | Always | Below 1 Ω |
| C160-1 (E2) - C39-97 (EEGL) | Always | Below 1 Ω |
| C106-3 (VC) or C39-120 (VCEG) - Body ground | Always | 10 kΩ or higher |
| C106-2 (VTA) or C39-59 (EGRA) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector (to Electric EGR Valve Assembly) |
Disconnect the electric EGR control valve assembly connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C106-3 (VC) - C106-1 (E2) | Ignition switch ON | 4.5 to 5.5 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the electric EGR control valve assembly.
Click hereEngine / Hybrid System>1VD-FTV (EMISSION CONTROL)>EGR VALVE (w/ DPF)>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs.
Turn the ignition switch off and wait for 30 seconds or more.
Turn the ignition switch to ON for 5 seconds or more.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Confirm that the DTC is not output again.
DTC is not output again.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the ECM.
Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Repair or replace the harness or connector.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs.
Turn the ignition switch off and wait for 30 seconds or more.
Turn the ignition switch to ON for 5 seconds or more.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Confirm that the DTC is not output again.
| Proceed to |
|---|
| NEXT |
NEXT