Home › Drivetrain › Q710 (HYBRID TRANSMISSION / TRANSAXLE) › SHIFT CONTROL POWER SUPPLY (for LHD)
RM37H0E _52 Drivetrain _093826 Q710 HYBRID TRANSMISSION / TRANSAXLE _0442250 SHIFT CONTROL POWER SUPPLY(for LHD) A

Q710 HYBRID TRANSMISSION / TRANSAXLE  SHIFT CONTROL POWER SUPPLY(for LHD)  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
C453486N03
5.708,4.49 5.979,3.896 5.979,3.896 6.25,3.896 false 3.896,1.125 5.042,1.313 5.042,1.313 5.396,1.313 true 3.219,3.927 3.656,3.927 false 6.302,0.271 6.802,0.271 false 6.344,0.74 6.76,0.74 false 4.385,2.198 4.719,2.479 0.333,0.281 10 false x 2 2.667,3.708 3,3.99 0.333,0.281 10 false x 2 6.271,3.75 6.573,4.115 0.302,0.365 18 false 3 5.844,1.167 6.146,1.531 0.302,0.365 18 false 4 4.094,3.792 4.365,4.135 0.271,0.344 18 false 5 6.094,0.115 6.333,0.49 0.24,0.375 18 false 1 6.125,0.583 6.375,0.927 0.25,0.344 18 false 2

Procedure Part Name Code
Z101186

Z101188

Z101187

1 PRECAUTION - (Click here) - -
2 DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL - - - -
3 GLOVE COMPARTMENT DOOR ASSEMBLY 55550 - - -
4 PASSENGER SIDE JUNCTION BLOCK ASSEMBLY 82730D (Click here) - -
5 SHIFT CONTROL SUPPLY 894D1 (Click here) - -

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during shift control supply removal/installation are shown below.

Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)

HINT:

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Adaptive high beam system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Air conditioning system After the ignition switch is turned to ON, the servo motor and expansion valve standard position is recognized. -



PROCEDURE

Hide 1. PRECAUTION

Z101186

NOTICE:

After turning the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.

Click here(Click here)



Hide 2.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 55550 3.REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY

Hide 82730D 4.DISCONNECT PASSENGER SIDE JUNCTION BLOCK ASSEMBLY

a.
C444801

i.

Remove the bolt, nut and disconnect the ECU.



b.
C444758C01
0.052,0.021 0.5,0.385 0.448,0.365 18 true i, ii 3.74,0.021 4.052,0.396 0.313,0.375 18 false iii 1.896,2.073 2.198,2.427 0.302,0.354 18 false iv
V113147

Disconnect - -


i.

Disconnect the 2 wire harness clamps.


ii.

Disconnect the 4 connectors.


iii.

Remove the 2 nuts.


iv.

Detach the 3 claws on the wire harness protector while pulling off the passenger side junction block assembly, and disconnect the passenger side junction block assembly.

HINT:

Position the passenger side junction block assembly so it does not interfere with the removal of the shift control supply.




Hide 894D1 5.REMOVE SHIFT CONTROL SUPPLY

Z101186

NOTICE:

If the shift control supply is subjected to any strong impact (such as being dropped), replace it with a new one.



a.
C437308