Home › Drivetrain › Q710 (HYBRID TRANSMISSION / TRANSAXLE) › SHIFT CONTROL POWER SUPPLY (for RHD)
RM37H0E _52 Drivetrain _093826 Q710 HYBRID TRANSMISSION / TRANSAXLE _0443097 SHIFT CONTROL POWER SUPPLY(for RHD) A

Q710 HYBRID TRANSMISSION / TRANSAXLE  SHIFT CONTROL POWER SUPPLY(for RHD)  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
C453484N01
6.281,4.51 6.281,4.271 6.281,4.271 5.583,3.917 false 5.958,1.5 6.406,1.5 false 6.438,0.26 6.823,0.26 false 6.438,0.729 6.76,0.729 false 6.448,1.365 6.729,1.719 0.281,0.354 18 false 3 6.198,4.521 6.427,4.865 0.229,0.344 18 false 4 4.958,3.667 5.281,3.958 0.323,0.292 10 false x 2 6.219,0.104 6.438,0.458 0.219,0.354 18 false 1 6.208,0.573 6.438,0.917 0.229,0.344 18 false 2

Procedure Part Name Code
Z101186

Z101188

Z101187

1 PRECAUTION - (Click here) - -
2 DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL - - - -
3 LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY 55045 - - -
4 SHIFT CONTROL SUPPLY 894D1 (Click here) - -

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during shift control supply removal/installation are shown below.

Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)

HINT:

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Adaptive high beam system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Air conditioning system After the ignition switch is turned to ON, the servo motor and expansion valve standard position is recognized. -



PROCEDURE

Hide 1. PRECAUTION

Z101186

NOTICE:

After turning the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.

Click here(Click here)



Hide 2.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 55045 3.REMOVE LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY

Hide 894D1 4.REMOVE SHIFT CONTROL SUPPLY

Z101186

NOTICE:
·

If the shift control supply is subjected to any strong impact (such as being dropped), replace it with a new one.

·

When pulling off the shift control supply from the installation location, do not allow it to get caught on the wire harness in the surrounding area.




a.
E450292N01
0.281,0.052 0.563,0.406 0.281,0.354 18 false i

i.

Remove the 2 nuts and disconnect the ECU.



b.
C444774N01
0.146,0.042 0.333,0.417 0.188,0.375 18 false i 3.521,0.052 4.083,0.448 0.563,0.396 18 false ii, iii

i.

Detach the wire harness clamp from the shift control supply.


ii.

Disconnect the shift control supply connector.


iii.

Remove the 2 bolts and shift control supply from the body.