Home › Drivetrain › Q710 (HYBRID TRANSMISSION / TRANSAXLE) › MOTOR CABLE
RM37H0E _52 Drivetrain _093826 Q710 HYBRID TRANSMISSION / TRANSAXLE _0442236 MOTOR CABLE A

Q710 HYBRID TRANSMISSION / TRANSAXLE  MOTOR CABLE  INSTALLATION  


CAUTION / NOTICE / HINT

COMPONENTS (INSTALLATION)
C443313N02
2.635,0.74 3.719,0.99 1.083,0.25 4.813,2.615 5.896,2.865 1.083,0.25 1.792,1.344 2.875,1.594 1.083,0.25 4.771,2.573 5.938,2.906 1.167,0.333 1.75,1.302 2.917,1.635 1.167,0.333 4.469,0.875 3.719,0.875 false 4.552,1.51 5.469,1.51 false 3.625,1.469 2.875,1.469 false 4.813,2.75 4.646,2.75 4.646,2.75 4.042,1.854 false 5.073,2.156 4.906,2.156 4.906,2.156 4.167,1.625 false 1.688,5.115 1.906,5.115 1.906,5.115 2.656,4.885 false 4.531,3.104 4.365,3.104 4.365,3.104 3.552,2.208 false 2.719,0.792 3.854,1.01 1.135,0.219 8 false 8.0 (82, 71 in.*lbf) 4.469,1 4.927,1.198 0.458,0.198 10 false x 2 4.906,2.667 6.042,2.885 1.135,0.219 8 false 8.0 (82, 71 in.*lbf) 1.906,1.385 3.042,1.604 1.135,0.219 8 false 8.0 (82, 71 in.*lbf) 3.698,1.458 4.156,1.656 0.458,0.198 10 false x 2 4.115,1.76 4.573,1.958 0.458,0.198 10 false x 3 1.49,4.958 1.771,5.313 0.281,0.354 18 false 4 4.896,2.969 5.177,3.323 0.281,0.354 18 false 1 5.531,2.021 5.823,2.354 0.292,0.333 18 false 2 5.76,1.406 6.073,1.719 0.313,0.313 18 false 3 5.406,2.083 5.563,2.281 0.156,0.198 10 false ●

Procedure Part Name Code
Z101186

Z101188

Z101187

1 MOTOR CABLE G1148 (Click here) - -
2 MOTOR CABLE TERMINAL CAP G114D (Click here) - -
3 CONNECTOR COVER 82821T (Click here) - -
4 REAR SUSPENSION MEMBER SUB-ASSEMBLY 51206A - - -

V111893

Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf)
V100146

N*m (kgf*cm, ft.*lbf): Specified torque
● Non-reusable part - -

PROCEDURE

Hide G1148 1.INSTALL MOTOR CABLE

Z101186

CAUTION:

Wear insulated gloves.


NOTICE:
·

Do not touch the waterproof seal or terminals of the motor cable.

·

To prevent the motor cable from contacting the FCV with motor transaxle assembly, make sure that the hybrid motor control inverter assembly side of the motor cable is wrapped with a plastic bag or equivalent until directly before reconnection.




a.
C443268C01
1.958,0.052 2.49,0.51 0.531,0.458 18 false i
V100135

Bolt A
V100136

Bolt B


i.

Using an insulated tool, install the motor cable to the FCV with motor transaxle assembly with the 5 bolts shown in the illustration.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)

HINT:

Tightening order: Temporarily install bolts A → Tighten bolts A → Temporarily install bolts B → Tighten bolts B




Hide G114D 2.INSTALL MOTOR CABLE TERMINAL CAP

Z101186

CAUTION:

Wear insulated gloves.


NOTICE:
·

Do not pinch the O-ring.

·

Make sure the terminal cap is securely attached.




Hide 82821T 3.INSTALL CONNECTOR COVER

Z101186

CAUTION:

Wear insulated gloves.



a.
C443270N02
0.354,0.01 0.635,0.365 0.281,0.354 18 false i 3.771,0.031 4.052,0.385 0.281,0.354 18 false ii

i.

Using an insulated tool, install the connector cover to the FCV with motor transaxle assembly with the 2 bolts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


ii.

Attach the clamp.



Hide 51206A 4.INSTALL REAR SUSPENSION MEMBER SUB-ASSEMBLY