Home › Audio / Visual / Telematics › AUDIO / VIDEO › NOISE FILTER
RM37H0E _56 Audio / Visual / Telematics _095260 AUDIO / VIDEO _0448062 NOISE FILTER A

AUDIO / VIDEO  NOISE FILTER  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
E455321N04
4.708,1.51 6.573,3.281 1.865,1.771 5.063,1.729 5.542,1.729 false 5.188,0.729 5.708,0.729 false 2.208,3.406 2.552,3.406 false 3.708,0.99 4.313,0.99 false 1.177,1.74 1.177,2.208 false 2.646,2.135 3.01,2.135 false 3.771,2.583 4.115,2.583 false 5.188,2.156 5.188,1.729 5.188,1.729 5.542,1.729 false 5.719,3.292 5.719,3.438 false 0.042,0.042 0.417,0.281 0.375,0.24 12 false *A 1.094,2.24 1.375,2.594 0.281,0.354 18 false 1 2.021,3.26 2.208,3.542 0.188,0.281 18 false 2 3.26,1.979 3.448,2.26 0.188,0.281 18 false 3 4.198,2.396 4.385,2.677 0.188,0.281 18 false 4 4.365,0.833 4.552,1.115 0.188,0.281 18 false 5 6.104,0.615 6.292,0.896 0.188,0.281 18 false 6 5.854,3.385 6.042,3.667 0.188,0.281 18 false 6 5.948,0.667 6.104,0.865 0.156,0.198 10 false ● 4.76,1.646 5.083,1.833 0.323,0.188 10 false ● *1 5.719,3.448 5.885,3.646 0.167,0.198 10 false ●

Procedure Part Name Code
Z101186

Z101188

Z101187

1 BENCH TYPE REAR SEATBACK ASSEMBLY - - - -
2 REAR DOOR SCUFF PLATE INSIDE LH 67918F - - -
3 REAR DOOR OPENING TRIM WEATHERSTRIP LH 62332A (Click here) - -
4 REAR SEAT SIDE GARNISH LH 62552F - - -
5 NO. 1 ROOM PARTITION PAD 64273D - - -
6 RADIO SETTING CONDENSER 86011V (Click here) - -

*A for High Mounted Stop Light - -
*1 TERMINAL COVER - -
● Non-reusable part - -

E461226N01
5.031,0.104 7.031,1.531 2,1.427 2.677,1.292 2.885,0.875 2.885,0.875 3.188,0.875 false 6.448,1.104 6.646,1.104 false 5.604,2.729 5.156,2.729 false 6.115,1.542 6.115,1.74 false 0.031,0.031 0.406,0.271 0.375,0.24 12 false *A 3.25,0.729 3.438,1.073 0.188,0.344 18 false 7 6,2.583 6.24,2.865 0.24,0.281 18 false 8 6.25,1.688 6.417,1.969 0.167,0.281 18 false 8 6.698,1 7.031,1.219 0.333,0.219 10 false ● *1 5.854,2.615 6.01,2.813 0.156,0.198 10 false ● 6.083,1.76 6.24,1.958 0.156,0.198 10 false ●

Procedure Part Name Code
Z101186

Z101188

Z101187

7 PACKAGE TRAY TRIM PANEL ASSEMBLY 64330 - - -
8 RADIO SETTING CONDENSER 86011R (Click here) - -

*A for Window Defogger - -
*1 TERMINAL COVER - -
● Non-reusable part - -

PROCEDURE

Hide 1.REMOVE BENCH TYPE REAR SEATBACK ASSEMBLY (for High Mounted Stop Light)

Hide 67918F 2.REMOVE REAR DOOR SCUFF PLATE INSIDE LH (for High Mounted Stop Light)

Hide 62332A 3.REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH (for High Mounted Stop Light)

Z101186

HINT:

Pull back the rear door opening trim weatherstrip LH so that the rear seat side garnish LH can be removed.

Click here(Click here)



Hide 62552F 4.REMOVE REAR SEAT SIDE GARNISH LH (for High Mounted Stop Light)

Hide 64273D 5.REMOVE NO. 1 ROOM PARTITION PAD (for High Mounted Stop Light)

a.
E454194C01
0,0 0,0 false
V113147

Remove in this Direction - -



Hide 86011V 6.REMOVE RADIO SETTING CONDENSER (for High Mounted Stop Light)

Z101186

NOTICE:

When a terminal cover is removed, the radio setting condenser must be replaced because the terminal covers and condenser are supplied as a set.



a.
E455322N01
1.875,0.031 2.219,0.313 0.344,0.281 18 false i, ii

i.

Remove the bolt.


ii.

Detach the clamp and disconnect the radio setting condenser with wire harness from the vehicle body.



b.
E461228C02
0.469,0.156 0.604,0.479 0.135,0.323 18 false i 4.156,0.146 4.292,0.469 0.135,0.323 18 false ii 4.177,2.729 4.74,3.052 0.563,0.323 18 false iii, iv
V113147

Remove in this Direction - -


i.

Detach the claw and pull out the cover as shown in the illustration.


ii.

Using a screwdriver, detach the claw and remove the 2 terminal covers with wire harness from the condenser.


iii.

Using a screwdriver, bend back and break off the claw as shown in the illustration.


iv.

Remove the terminal cover from the wire harness.

NOTICE:
·

Make sure to hold the crimping side of the terminal when disconnecting the wire harness from the terminal cover.

·

Make sure not to bend the exposed wire when disconnecting the wire harness from the terminal cover.

·

Check for deformation of the terminal after the wire harness has been removed from the terminal cover.





Hide 64330 7.REMOVE PACKAGE TRAY TRIM PANEL ASSEMBLY (for Window Defogger)

Hide 86011R 8.REMOVE RADIO SETTING CONDENSER (for Window Defogger)

Z101186

NOTICE:

When a terminal cover is removed, the radio setting condenser must be replaced because the terminal covers and condenser are supplied as a set.



a.
E455423C02
0.146,0.135 0.49,0.427 0.344,0.292 18 false i, ii 3.896,0.125 4.24,0.417 0.344,0.292 18 false iii 2.479,2.135 3.021,2.417 0.542,0.281 18 false iv, v
V113147

Remove in this Direction - -


i.

Remove the bolt.


ii.

Detach the clamp and disconnect the radio setting condenser with wire harness from the vehicle body.


iii.

Using a screwdriver, detach the claw and remove the 2 terminal covers with wire harness from the condenser.


iv.

Using a screwdriver, bend back and break off the claw as shown in the illustration.


v.

Remove the terminal cover from the wire harness.

NOTICE:
·

Make sure to hold the crimping side of the terminal when disconnecting the wire harness from the terminal cover.

·

Make sure not to bend the exposed wire when disconnecting the wire harness from the terminal cover.

·

Check for deformation of the terminal after the wire harness has been removed from the terminal cover.