Home › Audio / Visual / Telematics › AUDIO / VIDEO › NOISE FILTER
RM37H0E _56 Audio / Visual / Telematics _095260 AUDIO / VIDEO _0448062 NOISE FILTER A

AUDIO / VIDEO  NOISE FILTER  INSTALLATION  


CAUTION / NOTICE / HINT

COMPONENTS(INSTALLATION)
E461226N02
5.031,0.104 7.031,1.531 2,1.427 4.031,2.979 5.01,3.156 0.979,0.177 2.719,1.323 2.969,0.844 2.969,0.844 3.271,0.844 false 6.448,1.104 6.646,1.104 false 5.604,2.729 5.156,2.729 false 6.115,1.542 6.115,1.74 false 4.531,2.979 4.531,2.406 false 0.031,0.031 0.406,0.271 0.375,0.24 12 false *A 6,2.573 6.188,2.865 0.188,0.292 18 false 1 6.229,1.688 6.385,1.948 0.156,0.26 18 false 1 3.323,0.698 3.49,0.979 0.167,0.281 18 false 2 6.688,1.01 6.99,1.229 0.302,0.219 10 false ● *1 5.865,2.635 6.052,2.844 0.188,0.208 10 false ● 6.083,1.74 6.24,1.938 0.156,0.198 10 false ● 4.073,3 5.052,3.146 0.979,0.146 8 false 7.5 (76, 66 in.*lbf)

Procedure Part Name Code
Z101186

Z101188

Z101187

1 RADIO SETTING CONDENSER 86011R (Click here) - -
2 PACKAGE TRAY TRIM PANEL ASSEMBLY 64330 - - -

*A for Window Defogger - -
*1 TERMINAL COVER - -
V100146

N*m (kgf*cm, ft.*lbf): Specified torque ● Non-reusable part

E458195N02
4.708,1.51 6.573,3.281 1.865,1.771 5.135,0.333 6.125,0.531 0.99,0.198 5.063,1.729 5.542,1.729 false 5.188,0.729 5.708,0.729 false 2.208,3.406 2.552,3.406 false 3.708,0.99 4.313,0.99 false 1.177,1.74 1.177,2.208 false 2.688,2.021 2.917,2.021 false 3.771,2.583 4.115,2.583 false 5.188,2.156 5.188,1.729 5.188,1.729 5.542,1.729 false 5.719,3.292 5.719,3.438 false 4.781,0.427 5.125,0.427 false 0.042,0.042 0.417,0.281 0.375,0.24 12 false *A 6.083,0.594 6.26,0.875 0.177,0.281 18 false 3 4.375,0.823 4.563,1.104 0.188,0.281 18 false 4 4.177,2.438 4.365,2.719 0.188,0.281 18 false 5 3.229,1.844 3.417,2.125 0.188,0.281 18 false 6 2.042,3.229 2.229,3.51 0.188,0.281 18 false 7 1.094,2.24 1.281,2.521 0.188,0.281 18 false 8 5.938,0.646 6.094,0.844 0.156,0.198 10 false ● 4.75,1.667 5.073,1.854 0.323,0.188 10 false ● *1 5.698,3.427 5.865,3.625 0.167,0.198 10 false ● 5.177,0.365 6.156,0.5 0.979,0.135 8 false 7.5 (76, 66 in.*lbf) 5.844,3.375 6.052,3.625 0.208,0.25 18 false 3

Procedure Part Name Code
Z101186

Z101188

Z101187

3 RADIO SETTING CONDENSER 86011V (Click here) - -
4 NO. 1 ROOM PARTITION PAD 64273D - - -
5 REAR SEAT SIDE GARNISH LH 62552F - - -
6 REAR DOOR OPENING TRIM WEATHERSTRIP LH 62332A (Click here) - -
7 REAR DOOR SCUFF PLATE INSIDE LH 67918F - - -
8 BENCH TYPE REAR SEATBACK ASSEMBLY - - - -

*A for High Mounted Stop Light - -
*1 TERMINAL COVER - -
V100146

N*m (kgf*cm, ft.*lbf): Specified torque ● Non-reusable part

PROCEDURE

Hide 86011R 1.INSTALL RADIO SETTING CONDENSER (for Window Defogger)

a.
E455424C01
1.031,0.083 1.323,0.417 0.292,0.333 18 false i 1.656,2.01 2.229,2.281 0.573,0.271 18 false iii, iv 4.219,0.094 4.51,0.427 0.292,0.333 18 false ii
V113147

Install in this Direction - -


i.

Attach the claw to install a new terminal cover to the wire harness.

NOTICE:
·

Make sure to hold the crimping side of the terminal when installing the wire harness to the terminal cover.

·

Make sure not to bend the exposed wire when installing the wire harness to the terminal cover.

·

Do not use excessive force when inserting the wire harness into the terminal cover.

·

If the terminal cover has been deformed during installation, replace the terminal and terminal cover with new ones.




ii.

Attach the claw to install a new terminal cover with wire harness to a new condenser.

NOTICE:
·

Do not use excessive force when inserting the terminal cover into the condenser.

·

If the terminal cover has been deformed during installation, replace the terminal, terminal cover and condenser with new ones.




iii.

Attach the clamp to temporarily install a new radio setting condenser with wire harness.


iv.

Install the radio setting condenser with the bolt.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)



Hide 64330 2.INSTALL PACKAGE TRAY TRIM PANEL ASSEMBLY (for Window Defogger)

Hide 86011V 3.INSTALL RADIO SETTING CONDENSER (for High Mounted Stop Light)

a.
E435797C02
0.573,0.177 0.854,0.531 0.281,0.354 18 false i 3.729,0.156 4.01,0.51 0.281,0.354 18 false ii 3.708,1.958 3.99,2.313 0.281,0.354 18 false iii
V113147

Install in this Direction - -


i.

Attach the claw to install a new terminal cover to the wire harness.

NOTICE:
·

Make sure to hold the crimping side of the terminal when installing the wire harness to the terminal cover.

·

Make sure not to bend the exposed wire when installing the wire harness to the terminal cover.

·

Do not use excessive force when inserting the wire harness into the terminal cover.

·

If the terminal cover has been deformed during installation, replace the terminal and terminal cover with new ones.




ii.

Attach the claw to install 2 new terminal covers with wire harness to a new condenser.

NOTICE:
·

Do not use excessive force when inserting the terminal covers into the condenser.

·

If a terminal cover has been deformed during installation, replace the terminal, terminal covers and condenser with new ones.




iii.

Insert the cover as shown in the illustration and attach the claw.



b.
E455322N02
1.823,0.031 2.167,0.333 0.344,0.302 18 false i, ii

i.

Attach the clamp to temporarily install a new radio setting condenser with wire harness.


ii.

Install the radio setting condenser with the bolt.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)



Hide 64273D 4.INSTALL NO. 1 ROOM PARTITION PAD (for High Mounted Stop Light)

Hide 62552F 5.INSTALL REAR SEAT SIDE GARNISH LH (for High Mounted Stop Light)

Hide 62332A 6.INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH (for High Mounted Stop Light)

Z101186

Click here(Click here)

Hide 67918F 7.INSTALL REAR DOOR SCUFF PLATE INSIDE LH (for High Mounted Stop Light)

Hide 8.INSTALL BENCH TYPE REAR SEATBACK ASSEMBLY (for High Mounted Stop Light)