Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › STEERING PAD › 2020.11–2021.08
RM37H0E _58 Vehicle Interior _095287 SUPPLEMENTAL RESTRAINT SYSTEMS _0448066 STEERING PAD A

SUPPLEMENTAL RESTRAINT SYSTEMS  STEERING PAD  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
B593184N02
0.427,2.948 1.344,3.594 0.917,0.646 4.042,1.115 6.438,3.01 2.396,1.896 6.427,0.229 6.833,0.229 false 6.406,0.615 6.813,0.615 false 1.344,3.313 6.583,3.313 6.583,3.313 6.583,2.729 false 6.438,2.729 6.688,2.729 false 4.656,2.771 5.063,2.771 false 0.688,3.208 1.094,3.208 false 6.198,0.094 6.479,0.448 0.281,0.354 18 false 1 6.958,2.625 7.156,2.99 0.198,0.365 18 false 3 6.219,0.469 6.5,0.823 0.281,0.354 18 false 2 5.135,2.688 5.448,2.885 0.313,0.198 10 false *2 1.135,3.135 1.448,3.333 0.313,0.198 10 false *1

Procedure Part Name Code
Z101186

Z101188

Z101187

1 PRECAUTION - (Click here) - -
2 DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL - (Click here) - -
3 HORN BUTTON ASSEMBLY 45130 (Click here) - -

*1 LOWER NO. 3 STEERING WHEEL COVER *2 LOWER NO. 2 STEERING WHEEL COVER

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the horn button assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary procedures Effect/Inoperative Function When Necessary Procedures are not Performed Link
Disconnect cable from negative auxiliary battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)

HINT:

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Adaptive high beam system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Air conditioning system After the ignition switch is turned to ON, the servo motor and expansion valve standard position is recognized. -



PROCEDURE

Hide 1. PRECAUTION

Z101186

CAUTION:
B475753

Be sure to read precaution thoroughly before servicing.

Click here(Click here)


NOTICE:

After the ignition switch is turned off, there may be a waiting time before disconnecting the auxiliary negative (-) battery terminal.

Click here(Click here)



Hide 2.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

Z101186

CAUTION:
B422343

·

Wait at least 60 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.




Click hereGeneral>MAINTENANCE>AUXILIARY BATTERY>REMOVAL

Hide 45130 3.REMOVE HORN BUTTON ASSEMBLY

Z101186

CAUTION:
B528833

·

When storing the horn button assembly, keep the airbag deployment side facing upward.

·

If the airbag deploys for any reason, it may cause a serious accident.




a.
B605562C01
1.042,0.458 1.833,0.458 true 0.458,0.104 0.74,0.458 0.281,0.354 18 false i 4.49,0.156 4.771,0.51 0.281,0.354 18 false ii 0.813,0.375 1.042,0.604 0.229,0.229 10 true *a
*a Turns off - -


i.

Check that the ignition switch is off.


ii.

Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

CAUTION:
·

Wait at least 60 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.





b.
B605564C02
1.688,1.646 1.969,2 0.281,0.354 18 false i 2.604,1.281 2.885,1.635 0.281,0.354 18 false ii 0.458,3.146 0.74,3.5 0.281,0.354 18 false v 2.052,1.26 2.333,1.615 0.281,0.354 18 false ii 4.24,1.292 4.521,1.646 0.281,0.354 18 false iv 5.406,1.198 5.688,1.552 0.281,0.354 18 false iv 4.5,4.229 4.833,4.552 0.333,0.323 18 true vii 5.25,1.625 5.531,1.979 0.281,0.354 18 false iii 4.292,5.417 4.573,5.771 0.281,0.354 18 false vi 6.208,4.25 6.563,4.542 0.354,0.292 18 true viii 5.031,5.052 5.292,5.354 0.26,0.302 18 true ix
V113147

Release in this Direction - -


i.

Apply protective tape to the areas shown in the illustration.


ii.

Using a screwdriver, insert the screwdriver into the cutout of the lower No. 2 steering wheel cover and detach the claw and guide to remove the lower No. 2 steering wheel cover.

HINT:

Tape the screwdriver tip before use.



iii.

Apply protective tape to the areas shown in the illustration.


iv.

Using a screwdriver, insert the screwdriver into the cutout of the lower No. 3 steering wheel cover and detach the claw and guide to remove the lower No. 3 steering wheel cover.

HINT:

Tape the screwdriver tip before use.



v.

Using a screwdriver with its tip wrapped with protective tape, push in the torsion springs to detach the pins as shown in the illustration.

HINT:

Insert the screwdriver into the installation areas of the lower No. 2 steering wheel cover and lower No. 3 steering wheel cover.



vi.

Tilt the horn button assembly toward the seat and support it with one hand.

NOTICE:
·

Do not drop the horn button assembly.

·

When disconnecting the horn button assembly, do not pull the airbag wire harness.




vii.

Detach the wire harness clamp.


viii.

Disconnect the airbag connector.

NOTICE:

When disconnecting any airbag connector, take care not to damage the airbag wire harness.


HINT:

Refer to How to Connect or Disconnect Airbag Connector: Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>HOW TO CONNECT OR DISCONNECT AIRBAG CONNECTOR



ix.

Disconnect the horn connector and remove the horn button assembly.