Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SENSOR
RM37H0E _56 Audio / Visual / Telematics _095293 PARK ASSIST / MONITORING _0448135 BLIND SPOT MONITOR SENSOR A

PARK ASSIST / MONITORING  BLIND SPOT MONITOR SENSOR  INSTALLATION  


CAUTION / NOTICE / HINT

COMPONENTS (INSTALLATION)
B594857N01
1.031,1.979 1.698,2.146 0.667,0.167 4.531,0.813 5.198,0.979 0.667,0.167 6.458,0.24 6.76,0.24 false 4.875,0.5 4.875,0.813 false 3.521,0.5 4.198,0.5 false 2.708,2.177 3.385,2.177 false 1.302,0.646 1.604,0.646 1.604,0.646 1.865,1.031 false 1.365,1.667 1.365,1.979 false 6.448,0.646 6.75,0.646 false 1.104,0.51 1.385,0.865 0.281,0.354 18 false 1 3.323,0.354 3.604,0.708 0.281,0.354 18 false 2 2.521,2.052 2.802,2.406 0.281,0.354 18 false 4 6.24,0.104 6.771,0.469 0.531,0.365 18 false 3 4.948,0.469 5.406,0.667 0.458,0.198 10 false x 3 1.49,1.573 1.948,1.771 0.458,0.198 10 false x 3 1.094,1.99 2.167,2.188 1.073,0.198 8 false 10 (102, 7) 4.594,0.823 5.667,1.021 1.073,0.198 8 false 10 (102, 7) 5.948,0.51 6.635,0.844 0.688,0.333 18 false 5, 6

Procedure Part Name Code
Z101186

Z101188

Z101187

1 BLIND SPOT MONITOR SENSOR LH 88172 - - -
2 BLIND SPOT MONITOR SENSOR RH 88162 - - -
3 PERFORM BLIND SPOT MONITOR SENSOR INSTALLATION CONDITION INSPECTION - (Click here) - -
4 REAR BUMPER ASSEMBLY - - - -
5 PERFORM BLIND SPOT MONITOR BEAM AXIS CONFIRMATION - - - (Click here)
6 PERFORM DIAGNOSTIC SYSTEM CHECK - - - (Click here)

V100146

N*m (kgf*cm, ft.*lbf): Specified torque - -

CAUTION / NOTICE / HINT

HINT:
·

The blind spot monitor beam axis inspection is performed to confirm whether the sensor is transmitting radio waves.

·

The blind spot monitor beam axis confirmation is performed to confirm whether the sensor's beam axis is correct, and perform adjustment of the beam axis by using reflector.

·

The blind spot monitor sensor installation condition inspection is performed to confirm whether the sensor is placed vertically to the ground (+/-2.2°) by using a jig, and that the sensor is 46 to 54° from the line parallel to the vehicle center line.



PROCEDURE

Hide 88172 1.INSTALL BLIND SPOT MONITOR SENSOR LH

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

Hide 88162 2.INSTALL BLIND SPOT MONITOR SENSOR RH

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

Hide 3.PERFORM BLIND SPOT MONITOR SENSOR INSTALLATION CONDITION INSPECTION

Z101186

Click here(Click here)

Hide 4.INSTALL REAR BUMPER ASSEMBLY

Hide 5.PERFORM BLIND SPOT MONITOR BEAM AXIS CONFIRMATION

Hide 6. PERFORM DIAGNOSTIC SYSTEM CHECK