Home › Vehicle Interior › HEATING / AIR CONDITIONING › PTC HEATER ASSEMBLY
RM37H0E _58 Vehicle Interior _095300 HEATING / AIR CONDITIONING _0448156 PTC HEATER ASSEMBLY A

HEATING / AIR CONDITIONING  PTC HEATER ASSEMBLY  INSTALLATION  


CAUTION / NOTICE / HINT

COMPONENTS (INSTALLATION)
E456046N04
2.042,3.75 2.323,4.219 2.323,4.219 2.635,4.219 false 5.302,3.604 5.479,3.125 5.479,3.125 6,3.125 false 2.969,4.083 3.25,4.438 0.281,0.354 18 false 1 6.042,2.969 6.323,3.323 0.281,0.354 18 false 2

Procedure Part Name Code
Z101186

Z101188

Z101187

1 QUICK HEATER ASSEMBLY 87710G (Click here) - -
2 STEERING COLUMN ASSEMBLY 45250 - - -

V100146

N*m (kgf*cm, ft.*lbf): Specified torque - -

CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 87710G 1.INSTALL QUICK HEATER ASSEMBLY

a.
E456049C02
1.125,0.25 1.219,0.25 true 1.146,0.406 1.24,0.406 true 2.094,0.448 2.302,0.219 2.302,0.219 2.531,0.219 true 1.417,1.25 1.698,1.25 1.698,1.25 1.938,1.115 true 1.24,0.177 1.552,0.375 0.313,0.198 10 false *b 1.271,0.344 1.583,0.542 0.313,0.198 10 false *c 0.677,0.031 0.813,0.292 0.135,0.26 18 true i 6.094,1.198 6.24,1.458 0.146,0.26 18 true ii 6.021,0.688 6.25,0.948 0.229,0.26 18 true iii 5.25,0.271 5.49,0.521 0.24,0.25 18 true iv 2.573,0.135 2.75,0.313 0.177,0.177 10 true *a 1.229,1.177 1.406,1.354 0.177,0.177 10 true *a
*a Matchmarks *b Heater Case Fitting Surface
*c Quick Heater Claw - -
V113147

Install in this Direction - -


i.

Align the matchmark on the quick heater assembly with the matchmark on the heater case as shown in the illustration, insert the quick heater assembly into the heater case and attach the claw.

NOTICE:
·
E382588C02
0.677,1.646 0.677,1 true 0.188,1.646 0.188,0.896 0.188,0.896 0.5,0.896 true 0.604,1.667 0.917,1.865 0.313,0.198 10 false *a 0.115,1.667 0.427,1.865 0.313,0.198 10 false *b
*a Element
*b Fin


Do not hold the quick heater assembly by the element or fin. Also, do not damage the quick heater assembly.

·

Foul odors may occur due to oil adhering to the quick heater assembly.

·

Check that the heights of the claw fitting surface on the heater case and the claw of the quick heater assembly are aligned.



HINT:
E387834C02
1.865,0.396 2.531,0.396 true 1.792,2.885 2.458,2.885 true 2.573,0.292 2.885,0.49 0.313,0.198 10 false *a 2.5,2.781 2.813,2.979 0.313,0.198 10 false *a 0.104,0.073 0.448,0.292 0.344,0.219 12 false *A 0.104,2.458 0.448,2.677 0.344,0.219 12 false *B
*A for LHD
*B for RHD
*a Screw Insertion Hole


If the claws of the quick heater assembly are damaged, install the quick heater assembly with screw (90159-60431).



ii.

Install the quick heater assembly with the screw.


iii.

Connect the 2 connectors.

HINT:

The 2 connectors can be connected in any position (top or bottom).



iv.

Attach the clamp.



Hide 45250 2.INSTALL STEERING COLUMN ASSEMBLY