Home › Vehicle Interior › HEATING / AIR CONDITIONING › PTC HEATER ASSEMBLY
RM37H0E _58 Vehicle Interior _095300 HEATING / AIR CONDITIONING _0448156 PTC HEATER ASSEMBLY A

HEATING / AIR CONDITIONING  PTC HEATER ASSEMBLY  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
E456046N03
2.042,3.75 2.323,4.219 2.323,4.219 2.635,4.219 false 5.302,3.604 5.479,3.125 5.479,3.125 6,3.125 false 2.969,4.083 3.25,4.438 0.281,0.354 18 false 2 6.042,2.969 6.323,3.323 0.281,0.354 18 false 1

Procedure Part Name Code
Z101186

Z101188

Z101187

1 STEERING COLUMN ASSEMBLY 45250 - - -
2 QUICK HEATER ASSEMBLY 87710G (Click here) - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the PTC heater assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary procedures Effect/Inoperative Function when Necessary Procedure not Performed Link
Disconnect cable from negative (-) auxiliary battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)
Steering sensor (Including removal and installation) Steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)

HINT:
·

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

-

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Adaptive high beam system

-

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Air conditioning system After the ignition switch is turned to ON, the servo motor and expansion valve standard position is recognized. -


·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 45250 1.REMOVE STEERING COLUMN ASSEMBLY

Hide 87710G 2.REMOVE QUICK HEATER ASSEMBLY

a.
E456048C02
1.885,0.25 2.021,0.531 0.135,0.281 18 true i 2.656,0.677 2.813,0.958 0.156,0.281 18 true ii 2.698,1.156 2.896,1.438 0.198,0.281 18 true iii 4.417,0.042 4.615,0.323 0.198,0.281 18 true iv
V113147

Remove in this Direction - -


i.

Detach the clamp.


ii.

Disconnect the 2 connectors.


iii.

Remove the screw.


iv.

Detach the claw and remove the quick heater assembly as shown in the illustration.

NOTICE:
E382588C02
0.677,1.646 0.677,1 true 0.188,1.646 0.188,0.896 0.188,0.896 0.5,0.896 true 0.604,1.667 0.917,1.865 0.313,0.198 10 false *a 0.115,1.667 0.427,1.865 0.313,0.198 10 false *b
*a Element
*b Fin


·

Do not hold the quick heater assembly by the element or fin. Also, do not damage the quick heater assembly.

·

Foul odors may occur due to oil adhering to the quick heater assembly.