Home › Steering › STEERING COLUMN › STEERING COLUMN ASSEMBLY (for Power Tilt and Power Telescopic Steering Column) › 2020.11–2021.08
RM37H0E _55 Steering _095770 STEERING COLUMN _0449635 STEERING COLUMN ASSEMBLY(for Power Tilt and Power Telescopic Steering Column) A

STEERING COLUMN  STEERING COLUMN ASSEMBLY(for Power Tilt and Power Telescopic Steering Column)  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
C447787N01
5.219,2.333 5.635,2.333 true 6.521,0.25 6.854,0.25 true 5.896,0.125 6.677,0.5 0.781,0.375 18 false 1 - 3 5.729,2.177 6.083,2.542 0.354,0.365 18 false 4

Procedure Part Name Code
Z101186

Z101188

Z101187

1 PRECAUTION - (Click here) - -
2 CUSTOMIZE POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM - (Click here) - -
3 ALIGN FRONT WHEELS FACING STRAIGHT AHEAD - - - -
4 STEERING WHEEL ASSEMBLY 45100 - - -

C447789N01
4.271,1.25 4.083,1.25 4.083,1.25 3.844,0.917 true 5,3.865 5.448,3.865 true 4.667,2.375 5.188,2.375 true 5.781,3.708 6.125,4.042 0.344,0.333 18 false 5 4.604,1.135 4.958,1.438 0.354,0.302 18 false 6 5.552,2.25 5.958,2.573 0.406,0.323 18 false 7 5.781,3.25 6.094,3.448 0.313,0.198 10 false x 3

Procedure Part Name Code
Z101186

Z101188

Z101187

5 LOWER STEERING COLUMN COVER 45287 (Click here) - -
6 UPPER STEERING COLUMN COVER 45286B (Click here) - -
7 TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY - (Click here) - -

C447790N01
4.5,5.063 4.667,5.375 4.667,5.375 4.833,5.375 true 4.604,3.76 4.792,3.969 4.792,3.969 4.958,3.969 true 4.104,0.885 4.208,0.521 4.208,0.521 4.375,0.521 true 4.865,2.604 5.031,2.917 5.031,2.917 5.198,2.917 true 1.333,0.667 1.5,0.417 1.5,0.417 1.667,0.417 true 4.917,5.229 5.26,5.542 0.344,0.313 18 false 8 5.052,3.823 5.448,4.146 0.396,0.323 18 false 9 5.281,2.771 5.823,3.094 0.542,0.323 18 false 10 1.719,0.333 2.115,0.656 0.396,0.323 10 false *1 4.646,0.396 5.021,0.719 0.375,0.323 18 false 11 4.125,3.094 4.438,3.292 0.313,0.198 10 false x 2 3.521,1.698 3.833,1.896 0.313,0.198 10 false x 2 4.073,4.208 4.385,4.406 0.313,0.198 10 false x 2

Procedure Part Name Code
Z101186

Z101188

Z101187

8 LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY 73900 - - -
9 AIR DUCT SUB-ASSEMBLY - - - -
10 NO. 2 HEATER TO REGISTER DUCT 55844 - - -
11 STEERING COLUMN ASSEMBLY 45250 (Click here) - -

*1 NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY - -

C447791N04
5.177,1.885 5.448,1.448 5.448,1.448 5.615,1.448 true 4.219,0.448 4.49,0.917 4.49,0.917 4.74,0.917 true 5.094,0.781 5.49,1.063 0.396,0.281 18 false 13 5.677,1.281 6.125,1.615 0.448,0.333 18 false 12

Procedure Part Name Code
Z101186

Z101188

Z101187

12 FRONT WHEEL LH - - - -
13 NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY 45260 (Click here) - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during steering column assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Steering sensor (Including removal and installation) Steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)
Steering lock ECU (steering lock actuator or upper bracket assembly) Code registration (Immobiliser system)
·

Wireless function

·

Smart function

·

Does not change to on (READY)


See Service Bulletin for the registration method.
Disconnect cable from negative auxiliary battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)

HINT:

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Adaptive high beam system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Air conditioning system After the ignition switch is turned to ON, theservo motor and expansion valve standardposition is recognized. -

·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 1. PRECAUTION

Z101186

Click here(Click here)

Hide 2. CUSTOMIZE POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM

Z101186

NOTICE:

Perform the customization settings before disconnecting the cable from the negative (-) auxiliary battery terminal. Otherwise, removal of the steering column cover becomes difficult.


HINT:

Record the customization settings before changing them.




b.

Move the steering wheel to its lowest and rearmost position.


Hide 3. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

C447753

Hide 45100 4.REMOVE STEERING WHEEL ASSEMBLY

Hide 45287 5.REMOVE LOWER STEERING COLUMN COVER

a.
C447792C01
5.083,2.677 5.25,2.677 5.25,2.677 5.354,2.521 true 6.74,2.667 6.573,2.667 6.573,2.667 6.531,2.51 true 3.635,5.573 3.469,5.573 3.469,5.573 3.427,5.417 true 0.125,0.083 0.458,0.417 0.333,0.333 18 false i 4.01,0.135 4.344,0.469 0.333,0.333 18 false ii 2.156,3.125 2.49,3.458 0.333,0.333 18 false iii 3.719,5.479 3.979,5.698 0.26,0.219 10 true *a 4.792,2.563 5.031,2.781 0.24,0.219 10 true *a 6.802,2.563 7.042,2.781 0.24,0.219 10 true *a
*a Felt - -
V113146

Push Area
V113147

Remove in this Direction (1)
V113148

Remove in this Direction (2)
V113149

Remove in this Direction (3)


i.

Remove the 3 screws.


ii.

Press the part in the direction of the arrow shown in the illustration to detach the claw.

NOTICE:

Do not damage the felt.



iii.

Detach the 2 claws and remove the lower steering column cover in the direction of the arrow shown in the illustration.

NOTICE:

Do not damage the tilt and telescopic switch and felt.




Hide 45286B 6.REMOVE UPPER STEERING COLUMN COVER

a.
C447793N01
0.448,0.063 0.729,0.417 0.281,0.354 18 false i 3.865,0.115 4.146,0.469 0.281,0.354 18 false ii

i.

Detach the claws and guides as shown in the illustration.


ii.

Disengage the claw to remove the upper steering column cover.



Hide 7.REMOVE TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY

Z101186

NOTICE:
·

Do not replace the spiral cable with sensor sub-assembly with the battery connected and the power switch on (IG).

·

Do not rotate the spiral cable with sensor sub-assembly without the steering wheel assembly installed, with the battery connected and the power switch on (IG).

·

Ensure that the steering wheel assembly is installed and aligned straight when inspecting the steering sensor.




a.
C447794C01
0.104,0.167 0.333,0.406 0.229,0.24 18 false i 1.917,3.083 2.167,3.333 0.25,0.25 18 false iii 4.167,0.167 4.396,0.406 0.229,0.24 18 false ii
*a Clamp - -
V113147

Remove in this Direction - -


i.

Disconnect each connector from the turn signal switch assembly with spiral cable sub-assembly.


ii.

Using pliers, support the band clamp while loosened.


iii.

Disengage the claw to remove the turn signal switch assembly with spiral cable sub-assembly from the steering column assembly.



Hide 73900 8.REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY

Hide 9.REMOVE AIR DUCT SUB-ASSEMBLY

a.
C447795C01
0,0 0,0 false
V113147

Remove in this Direction - -



Hide 55844 10.REMOVE NO. 2 HEATER TO REGISTER DUCT

a.
C447796


Hide 45250 11.REMOVE STEERING COLUMN ASSEMBLY

a.
C447797C01
2.083,0.667 1.917,0.667 1.917,0.667 1.479,1 true 1.583,1.063 1.917,0.667 true 2.135,0.563 2.333,0.76 0.198,0.198 10 true *a 0.917,1.302 1.208,1.604 0.292,0.302 18 true ii 4.042,0.031 4.292,0.281 0.25,0.25 18 true iii 2.083,3 2.552,3.281 0.469,0.281 18 true iv, v 0.427,0.073 0.635,0.333 0.208,0.26 18 true i
*a Matchmark - -


i.

Put matchmarks on the No. 2 steering intermediate shaft assembly and steering column assembly.


ii.

Remove the bolt.


iii.

Disconnect each connector and disengage each wire harness clamp from the steering column assembly.


iv.

Remove the 2 nuts, bolt and steering column assembly.


v.

Disconnect the steering column assembly from the No. 2 steering intermediate shaft assembly.



Hide 12.REMOVE FRONT WHEEL LH

Hide 45260 13.REMOVE NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY

a.
C447798C01
3.344,3.073 3.406,3.333 true 3.573,3.333 3.406,3.333 3.406,3.333 3.313,3.135 true 3.625,3.25 3.823,3.417 0.198,0.167 10 true *a 0.313,0.021 0.563,0.313 0.25,0.292 18 false i 4.021,0.042 4.292,0.344 0.271,0.302 18 false ii 1.958,2.031 2.479,2.365 0.521,0.333 18 false iii 2.698,2.396 2.979,2.688 0.281,0.292 18 true iv
*a Matchmark - -
V113147

Slide in this Direction - -


i.

Loosen the clamp.


ii.

Remove the bolt.


iii.

Slide the No. 2 steering intermediate shaft assembly and put matchmarks on the No. 2 steering intermediate shaft assembly and rack and pinion power steering gear assembly.


iv.

Remove the No. 2 steering intermediate shaft assembly from the vehicle.