Home › Vehicle Interior › HEATING / AIR CONDITIONING › CONDENSER
RM37H0E _58 Vehicle Interior _095300 HEATING / AIR CONDITIONING _0448157 CONDENSER A

HEATING / AIR CONDITIONING  CONDENSER  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
E456054N01
1.073,2.396 1.406,2.396 1.406,2.396 1.698,1.958 false 0.906,2.26 1.219,2.625 0.313,0.365 18 false 1

Procedure Part Name Code
Z101186

Z101188

Z101187

1 RADIATOR WITH CONDENSER ASSEMBLY - - - -

E456094N01
5.656,2 5.771,1.573 5.771,1.573 6.073,1.573 false 1.26,3.021 1.573,3.021 1.573,3.021 1.896,2.719 false 5.104,1.969 5.625,1.25 5.625,1.25 5.792,1.25 true 6.396,1.417 6.677,1.771 0.281,0.354 18 false 2 1.073,2.865 1.354,3.219 0.281,0.354 18 false 3 5.844,1.156 6,1.354 0.156,0.198 10 false ●

Procedure Part Name Code
Z101186

Z101188

Z101187

2 NO. 1 DISCHARGE HOSE SUB-ASSEMBLY 88703A (Click here) - -
3 COOLER CONDENSER ASSEMBLY 884A0 (Click here) - -

● Non-reusable part - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the cooler condenser assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary procedures Effect/Inoperative Function when Necessary Procedure not Performed Link
Disconnect cable from negative (-) auxiliary battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)
Front bumper assembly (Including removal and installation)
·

Measurement of ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


·

TOYOTA Parking assist- sensor system

·

Parking support brake system

·

Advanced park


w/ Advanced Park:
(Click here)
w/o Advanced Park:
(Click here)
Front television camera view adjustment Panoramic view monitor system (Click here)

HINT:
·

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

-

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Adaptive high beam system

-

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Air conditioning system After the ignition switch is turned to ON, the servo motor and expansion valve standard position is recognized. -


·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 1.REMOVE RADIATOR WITH CONDENSER ASSEMBLY

Hide 88703A 2.DISCONNECT NO. 1 DISCHARGE HOSE SUB-ASSEMBLY

a.
E460118N01
0.813,0.083 0.958,0.354 0.146,0.271 18 true i 4.552,0.083 4.771,0.365 0.219,0.281 18 false ii

i.

Remove the bolt and disconnect the No. 1 discharge hose sub-assembly.


ii.

Remove the O-ring from the No. 1 discharge hose sub-assembly.

NOTICE:

Seal the openings of the disconnected parts using vinyl tape to prevent moisture and foreign matter from entering them.




Hide 884A0 3.REMOVE COOLER CONDENSER ASSEMBLY

a.
E456096C01
0.927,0.188 1.208,0.542 0.281,0.354 18 false i
V113147

Remove in this Direction (1)
V113148

Remove in this Direction (2)
V113149

Remove in this Direction (3) - -


i.

Detach the claw and guide and remove the cooler condenser assembly as shown in the illustration.

NOTICE:

Do not damage the cooler condenser assembly and radiator assembly when removing the cooler condenser assembly.