Home › Vehicle Exterior › WINDOW / GLASS › QUARTER WINDOW GLASS
RM37H0E _59 Vehicle Exterior _095305 WINDOW / GLASS _0448203 QUARTER WINDOW GLASS A

WINDOW / GLASS  QUARTER WINDOW GLASS  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
E463032N01
3.302,0.979 3.302,1.313 false 5.167,2.323 5.167,2.448 5.167,2.448 5.563,2.448 false 1.698,2.969 1.698,3.198 false 5.979,2.333 6.26,2.688 0.281,0.354 18 false 3 3.26,1.313 3.542,1.667 0.281,0.354 18 false 1 5.823,2.313 6.104,2.667 0.281,0.354 18 false ● 1.656,3.208 1.938,3.563 0.281,0.354 18 false 2

Procedure Part Name Code
Z101186

Z101188

Z101187

1 CURTAIN SHIELD AIRBAG ASSEMBLY LH 62180A - - -
2 PACKAGE TRAY TRIM PANEL ASSEMBLY 64330 - - -
3 QUARTER WINDOW ASSEMBLY LH 62720A (Click here) - -

● Non-reusable part - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the quarter window glass assembly removal/installation are shown below.

Necessary Procedures after parts Removed/Installed/Replaced
Replacement Part or Procedures Necessary Procedures Effects/Inoperative when are not Performed Link
Disconnect cable from negative (-) auxiliary battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)

HINT:
·

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

-

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Adaptive high beam system


-

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Air conditioning system After the ignition switch is turned to ON, the servo motor and expansion valve standard position is recognized. -


·

Use the same procedure for the RH and LH sides.

·

Use the same procedure described for the LH side.



NOTICE:
·

Be sure to use the quarter window assembly adhesive (specialized for high-rigidity specification vehicles) as the adhesive for replacing the quarter window assembly.

·

Be sure to use the quarter window assembly adhesive (specialized for high-rigidity specification vehicles) as the adhesive for adjusting the quarter window assembly.



PROCEDURE

Hide 62180A 1.REMOVE CURTAIN SHIELD AIRBAG ASSEMBLY LH

Hide 64330 2.REMOVE PACKAGE TRAY TRIM PANEL ASSEMBLY

Hide 62720A 3.REMOVE QUARTER WINDOW ASSEMBLY LH

Z101186

NOTICE:

The windshield glass may fall during work. Therefore, use suction cups to hold the quarter window assembly LH from outside the vehicle.



a.
E455885C01
5.396,0.813 4.885,0.813 true 0.333,0.052 0.615,0.406 0.281,0.354 18 false i 3.896,0.052 4.177,0.406 0.281,0.354 18 false ii 4.719,0.74 5.031,0.938 0.313,0.198 10 false *a
*a Suction Cups - -


i.

Apply protective tape on the body surface around the outer edge of the quarter window assembly LH.


ii.

Install the suction cups to the quarter window assembly LH.



b.
E444304C01
0.948,4.896 1.281,4.719 true 4.958,4.823 5.323,4.688 false 5.438,1.083 5.094,1.229 false 1.896,1.573 2.083,1.885 0.188,0.313 18 false i 2.667,2.292 2.823,2.469 0.156,0.177 10 true A 2.927,2.135 3.073,2.292 0.146,0.156 10 true A 0.615,4.021 1.073,4.219 0.458,0.198 10 false A-A 4.604,0.104 5.063,0.302 0.458,0.198 10 false B-B 4.448,4.01 4.906,4.208 0.458,0.198 10 false C-C 3.188,2.5 3.313,2.677 0.125,0.177 10 true C 3.167,2 3.281,2.135 0.115,0.135 10 true B 3.104,2.313 3.219,2.458 0.115,0.146 10 true B 3.188,2.823 3.313,3 0.125,0.177 10 true C 0.781,4.833 1.094,5.031 0.313,0.198 10 false *a 4.938,1.167 5.25,1.365 0.313,0.198 10 false *a 4.802,4.75 5.115,4.948 0.313,0.198 10 false *a
*a Cut - -


i.

Using a utility knife, cut the position of the moulding shown in the illustration.

NOTICE:
·

Do not damage the quarter window assembly LH or body surface.

·

If the body panel is damaged, perform rust-prevention treatment after removing the quarter window assembly LH.





c.
E444305C01
4.323,1.104 4.823,1.104 true 3.354,1.125 3.5,1.01 3.5,1.01 3.031,0.688 true 4.167,0.729 4.49,0.427 4.49,0.427 4.406,0.865 true 2.771,0.865 2.406,0.885 2.406,0.885 2.646,0.698 true 4.125,1.365 4.573,1.542 true 0.396,0.063 0.99,0.365 0.594,0.302 18 false i 2.25,0.823 2.49,1.031 0.24,0.208 10 false *a 4.854,1.042 5.063,1.219 0.208,0.177 10 true *b 3.531,0.927 3.74,1.104 0.208,0.177 10 true *b 4.448,0.292 4.688,0.5 0.24,0.208 10 false *a 4.615,1.49 4.833,1.656 0.219,0.167 10 true *a
*a Piano Wire *b Clip


i.

When using a piano wire, perform the following procedure.

1. Pass the piano wire (0.6 mm is appropriate) and install both ends on the mighty puller as shown in the illustration.

2. Pull the piano wire back and forth and cut through the adhesive.

NOTICE:
·

Do not forcefully allow the piano wire to come to contact with the edges of the quarter window assembly LH.

·

Be careful as the piano wire will break if it crosses itself.





d.
E444306N01
0.438,0.052 0.667,0.323 0.229,0.271 18 false i

i.

Holding the suction cups, remove the quarter window assembly LH.

NOTICE:

Be careful not to drop the quarter window assembly LH.