Home › Vehicle Exterior › MIRROR (EXT) › OUTER REAR VIEW MIRROR
RM37H0E _59 Vehicle Exterior _095308 MIRROR (EXT) _0448220 OUTER REAR VIEW MIRROR G

MIRROR (EXT)  OUTER REAR VIEW MIRROR  INSPECTION  


PROCEDURE

Hide 87940 1.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH (w/o Reverse Shift-linked Mirror)

a.

Check the operation of the retractable mirror.

NOTICE:
·

Disconnect and reconnect the auxiliary battery between each mirror position check.

·

The mirror position cannot be changed manually when the auxiliary battery is connected. To change the mirror position manually, the auxiliary battery must be disconnected first.



i.
B237099C41
1.563,3.083 1.99,3.281 0.427,0.198 1.604,3.948 1.604,3.865 1.604,3.865 1.052,3.865 true 1.604,4.167 1.604,4.365 1.604,4.365 1.052,4.365 true 0.781,4.313 1,4.438 0.219,0.125 10 false MF 0.76,3.802 1,3.948 0.24,0.146 10 false MR 0.875,2.948 1.417,3.219 0.542,0.271 10 false *f 1.635,0.083 1.948,0.24 0.313,0.156 10 false *a 1.177,1.156 1.49,1.313 0.313,0.156 10 false *b 1.448,2.135 1.76,2.292 0.313,0.156 10 false *c 1.896,2.448 2.208,2.604 0.313,0.156 10 false *d 2.427,2.75 2.74,2.906 0.313,0.156 10 false *e 1.667,3.104 2.125,3.302 0.458,0.198 10 false E29
*a (A) Forward position
*b (B)
*c (C) Driving position
*d (D)
*e (E) Retracted position
*f Component without harness connected
(Outer Rear View Mirror Assembly LH)


Disconnect the outer rear view mirror assembly LH connector.


ii.

For each position: Disconnect the auxiliary battery, set the mirror position by hand, connect the auxiliary battery, and check the retractable mirror movement.

OK:
Tester Connection Condition Specified Condition

Click Location & Routing(E29)Location & Routing

Click Connector(E29)Body>Front Door Wire LH / Front Door Wire RH>Outer Rear View Mirror Assembly LH

Auxiliary battery positive (+) - E29-3(MR)
Auxiliary battery negative (-) - E29 -11(MF)
Forward position (A) Moves from (A) to (E)
Auxiliary battery positive (+) - E29 -11(MF)
Auxiliary battery negative (-) - E29-3(MR)
Forward position (A) Does not move
Auxiliary battery positive (+) - E29-3(MR)
Auxiliary battery negative (-) - E29-11(MF)
Position between forward position (A) and driving position (C) Moves from (B) to (E)
Auxiliary battery positive (+) - E29-11(MF)
Auxiliary battery negative (-) - E29-3(MR)
Position between forward position (A) and driving position (C) Moves from (B) to (A)
Auxiliary battery positive (+) - E29-3(MR)
Auxiliary battery negative (-) - E29-11(MF)
Driving position (C) Moves from (C) to (E)
Auxiliary battery positive (+) - E29-11(MF)
Auxiliary battery negative (-) - E29-3(MR)
Driving position (C) Does not move
Auxiliary battery positive (+) - E29-3(MR)
Auxiliary battery negative (-) - E29-11(MF)
Position between driving position (C) and retracted position (E) Moves from (D) to (E)
Auxiliary battery positive (+) - E29-11(MF)
Auxiliary battery negative (-) - E29-3(MR)
Position between driving position (C) and retracted position (E) Moves from (D) to (C)
Auxiliary battery positive (+) - E29-3(MR)
Auxiliary battery negative (-) - E29-11(MF)
Retracted position (E) Does not move
Auxiliary battery positive (+) - E29-11(MF)
Auxiliary battery negative (-) - E29-3(MR)
Retracted position (E) Moves from (E) to (C)


If the result is not as specified, replace the outer rear view mirror assembly LH.



b.

Check the operation of the mirror surface.

i.
B199931C37
1.521,1.646 1.927,1.854 0.406,0.208 1.396,2.896 1.396,3.135 true 1.24,2.688 0.917,2.688 true 1.229,2.885 1,3.125 true 1.281,3.188 1.542,3.375 0.26,0.188 10 false M+ 1.615,1.677 1.917,1.823 0.302,0.146 10 false E29 0.76,3.167 1.052,3.354 0.292,0.188 10 false MH 0.146,1.531 0.771,1.917 0.625,0.385 10 false *a 0.646,2.625 0.896,2.813 0.25,0.188 10 false MV
*a Component without harness connected
(Outer Rear View Mirror Assembly LH)


Disconnect the outer rear view mirror assembly LH connector.


ii.

Apply auxiliary battery voltage and check the operation of the mirror.

OK:
Tester Connection Specified Condition

Click Location & Routing(E29)Location & Routing

Click Connector(E29)Body>Front Door Wire LH / Front Door Wire RH>Outer Rear View Mirror Assembly LH

Auxiliary battery positive (+) - E29-1(MV)
Auxiliary battery negative (-) - E29-10(M+)
Turns upward
Auxiliary battery positive (+) - E29-10(M+)
Auxiliary battery negative (-) - E29-1(MV)
Turns downward
Auxiliary battery positive (+) - E29-10(M+)
Auxiliary battery negative (-) - E29-9(MH)
Turns inside
Auxiliary battery positive (+) - E29-9(MH)
Auxiliary battery negative (-) - E29-10(M+)
Turns outside


If the result is not as specified, replace the outer rear view mirror assembly LH.



c.

Check the side turn signal light assembly LH.

i.
B580872C29
1.448,0.26 1.969,0.5 0.521,0.24 2.135,1.531 2.365,1.531 2.365,1.531 2.365,1.698 true 1.604,2.01 1.604,1.594 true 2.333,1.75 2.625,1.99 0.292,0.24 10 false B 1.583,1.99 2.302,2.177 0.719,0.188 10 false - 0.104,0.156 0.313,0.365 0.208,0.208 10 false *a 1.594,0.323 1.885,0.563 0.292,0.24 10 false E29
*a Component without harness connected
(Outer Rear View Mirror Assembly LH)


Disconnect the outer rear view mirror assembly LH connector.


ii.

Apply auxiliary battery voltage to the terminals of the connector, and check the illumination condition.

OK:
Tester Connection Specified Condition

Click Location & Routing(E29)Location & Routing

Click Connector(E29)Body>Front Door Wire LH / Front Door Wire RH>Outer Rear View Mirror Assembly LH

Auxiliary battery positive (+) - E29-16(B)
Auxiliary battery negative (-) - E29-12(-)
Side turn signal light illuminates


If the result is not as specified, inspect the side turn signal light assembly LH or replace the outer rear view mirror assembly LH.

Click hereVehicle Exterior>LIGHTING (EXT)>SIDE TURN SIGNAL LIGHT ASSEMBLY>INSPECTION



d.

Check the operation of the mirror heater.

i.
B580872C30
1.448,0.26 1.969,0.5 0.521,0.24 0.76,1.167 1.594,1.167 1.594,1.167 1.594,1.333 true 1.604,2.01 1.604,1.594 true 0.646,1.104 0.938,1.344 0.292,0.24 10 false + 1.583,1.99 2.302,2.177 0.719,0.188 10 false - 0.104,0.156 0.313,0.365 0.208,0.208 10 false *a 1.594,0.323 1.885,0.563 0.292,0.24 10 false E29
*a Component without harness connected
(Outer Rear View Mirror Assembly LH)


Disconnect the outer rear view mirror assembly LH connector.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(E29)Location & Routing

Click Connector(E29)Body>Front Door Wire LH / Front Door Wire RH>Outer Rear View Mirror Assembly LH

E29-4(+) - E29-12(-) 25 °C (77 °F) 8.5 to 11.5 Ω



iii.

Connect the cable from the positive (+) auxiliary battery terminal to terminal 4 (+) and the negative (-) auxiliary battery terminal to terminal 12 (-), and then check that the mirror becomes warm.

HINT:

It takes a short time for the mirror to become warm.


OK:

Mirror becomes warm.


If the result is not as specified, inspect the outer mirror LH or replace the outer mirror actuator assembly LH.

Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR GLASS>INSPECTION



Hide 87910 2.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH (w/o Reverse Shift-linked Mirror)

a.

Check the operation of the retractable mirror.

NOTICE:
·

Disconnect and reconnect the auxiliary battery between each mirror position check.

·

The mirror position cannot be changed manually when the auxiliary battery is connected. To change the mirror position manually, the auxiliary battery must be disconnected first.



i.
B237589C40
1.5,3.042 1.927,3.302 0.427,0.26 1.542,3.958 1.542,3.875 1.542,3.875 1,3.875 true 1.552,4.188 1.552,4.396 1.552,4.396 1.01,4.396 true 0.771,4.333 0.969,4.469 0.198,0.135 10 false MF 0.74,3.813 0.958,3.958 0.219,0.146 10 false MR 1.771,0.083 2.083,0.24 0.313,0.156 10 false *a 2.26,0.99 2.573,1.146 0.313,0.156 10 false *b 1.979,2.125 2.292,2.281 0.313,0.156 10 false *c 1.458,2.469 1.771,2.625 0.313,0.156 10 false *d 0.885,2.635 1.198,2.792 0.313,0.156 10 false *e 0.458,3.219 0.771,3.375 0.313,0.156 10 false *f 1.604,3.104 2.063,3.302 0.458,0.198 10 false E11
*a (A) Forward position
*b (B)
*c (C) Driving position
*d (D)
*e (E) Retracted position
*f Component without harness connected
(Outer Rear View Mirror Assembly RH)


Disconnect the outer rear view mirror assembly RH connector.


ii.

For each position: Disconnect the auxiliary battery, set the mirror position by hand, connect the auxiliary battery, and check the retractable mirror movement.

OK:
Tester Connection Condition Specified Condition

Click Location & Routing(E11)Location & Routing

Click Connector(E11)Body>Front Door Wire LH / Front Door Wire RH>Outer Rear View Mirror Assembly RH

Auxiliary battery positive (+) - E11-3(MR)
Auxiliary battery negative (-) - E11 -11(MF)
Forward position (A) Moves from (A) to (E)
Auxiliary battery positive (+) - E11-11(MF)
Auxiliary battery negative (-) - E11-3(MR)
Forward position (A) Does not move
Auxiliary battery positive (+) - E11-3(MR)
Auxiliary battery negative (-) - E11-11(MF)
Position between forward position (A) and driving position (C) Moves from (B) to (E)
Auxiliary battery positive (+) - E11-11(MF)
Auxiliary battery negative (-) - E11-3(MR)
Position between forward position (A) and driving position (C) Moves from (B) to (A)
Auxiliary battery positive (+) - E11-3(MR)
Auxiliary battery negative (-) - E11-11(MF)
Driving position (C) Moves from (C) to (E)
Auxiliary battery positive (+) - E11-11(MF)
Auxiliary battery negative (-) - E11-3(MR)
Driving position (C) Does not move
Auxiliary battery positive (+) - E11-3(MR)
Auxiliary battery negative (-) - E11-11(MF)
Position between driving position (C) and retracted position (E) Moves from (D) to (E)
Auxiliary battery positive (+) - E11-11(MF)
Auxiliary battery negative (-) - E11-3(MR)
Position between driving position (C) and retracted position (E) Moves from (D) to (C)
Auxiliary battery positive (+) - E11-3(MR)
Auxiliary battery negative (-) - E11-11(MF)
Retracted position (E) Does not move
Auxiliary battery positive (+) - E11-11(MF)
Auxiliary battery negative (-) - E11-3(MR)
Retracted position (E) Moves from (E) to (C)


If the result is not as specified, replace the outer rear view mirror assembly RH.



b.

Check the operation of the mirror surface.

i.
B199930C40
1.583,1.708 1.938,1.917 0.354,0.208 1.406,2.896 1.406,3.125 true 1.229,2.698 0.927,2.698 true 1.229,2.885 0.99,3.135 true 1.281,3.156 1.531,3.354 0.25,0.198 10 false M+ 0.656,2.646 0.917,2.833 0.26,0.188 10 false MV 0.76,3.177 1.031,3.385 0.271,0.208 10 false MH 0.292,1.583 0.938,2.156 0.646,0.573 10 false *a 1.656,1.74 2.115,1.938 0.458,0.198 10 false E11
*a Component without harness connected
(Outer Rear View Mirror Assembly RH)


Disconnect the outer rear view mirror assembly RH connector.


ii.

Apply auxiliary battery voltage and check the operation of the mirror.

OK:
Tester Connection Specified Condition

Click Location & Routing(E11)Location & Routing

Click Connector(E11)Body>Front Door Wire LH / Front Door Wire RH>Outer Rear View Mirror Assembly RH

Auxiliary battery positive (+) - E11-1(MV)
Auxiliary battery negative (-) - E11-10(M+)
Turns upward
Auxiliary battery positive (+) - E11-10(M+)
Auxiliary battery negative (-) - E11-1(MV)
Turns downward
Auxiliary battery positive (+) - E11-9(MH)
Auxiliary battery negative (-) - E11-10(M+)
Turns inside
Auxiliary battery positive (+) - E11-10(M+)
Auxiliary battery negative (-) - E11-9(MH)
Turns outside


If the result is not as specified, replace the outer rear view mirror assembly RH.



c.

Check the side turn signal light assembly RH.

i.
B580872C32
1.458,0.354 1.854,0.615 0.396,0.26 2.104,2 2.104,1.583 true 1.594,2.021 1.594,1.604 true 2.083,2.01 2.25,2.177 0.167,0.167 10 false B 1.573,2.021 1.729,2.177 0.156,0.156 10 false - 0.104,0.104 0.417,0.302 0.313,0.198 10 false *a 1.552,0.406 2.01,0.604 0.458,0.198 10 false E11
*a Component without harness connected
(Outer Rear View Mirror Assembly RH)


Disconnect the outer rear view mirror assembly RH connector.


ii.

Apply auxiliary battery voltage to the terminals of the connector, and check the illumination condition.

OK:
Tester Connection Specified Condition

Click Location & Routing(E11)Location & Routing

Click Connector(E11)Body>Front Door Wire LH / Front Door Wire RH>Outer Rear View Mirror Assembly RH

Auxiliary battery positive (+) - E11-16(B)
Auxiliary battery negative (-) - E11-12(-)
Side turn signal light illuminates


If the result is not as specified, inspect the side turn signal light assembly RH or replace the outer rear view mirror assembly RH.

Click hereVehicle Exterior>LIGHTING (EXT)>SIDE TURN SIGNAL LIGHT ASSEMBLY>INSPECTION



d.

Check the operation of the mirror heater.

i.
B580872C33
1.448,0.26 1.969,0.5 0.521,0.24 0.76,1.167 1.594,1.167 1.594,1.167 1.594,1.333 true 1.604,2.01 1.604,1.594 true 0.646,1.104 0.938,1.344 0.292,0.24 10 false + 1.583,1.99 2.302,2.177 0.719,0.188 10 false - 0.104,0.156 0.313,0.365 0.208,0.208 10 false *a 1.594,0.323 1.885,0.563 0.292,0.24 10 false E11
*a Component without harness connected
(Outer Rear View Mirror Assembly RH)


Disconnect the outer rear view mirror assembly RH connector.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(E11)Location & Routing

Click Connector(E11)Body>Front Door Wire LH / Front Door Wire RH>Outer Rear View Mirror Assembly RH

E11-4(+) - E11-12(-) 25 °C (77 °F) 8.5 to 11.5 Ω



iii.

Connect the cable from the positive (+) auxiliary battery terminal to terminal 4 (+) and the negative (-) auxiliary battery terminal to terminal 12 (-), and then check that the mirror becomes warm.

HINT:

It takes a short time for the mirror to become warm.


OK:

Mirror becomes warm.


If the result is not as specified, inspect the outer mirror RH or replace the outer mirror actuator assembly RH.

Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR GLASS>INSPECTION



Hide 87940 3.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH (w/ Reverse Shift-linked Mirror)

a.

Check the operation of the retractable mirror.

NOTICE:
·

Disconnect and reconnect the auxiliary battery between each mirror position check.

·

The mirror position cannot be changed manually when the auxiliary battery is connected. To change the mirror position manually, the auxiliary battery must be disconnected first.



i.
B237099C40
1.563,3.083 1.99,3.281 0.427,0.198 1.604,3.948 1.604,3.865 1.604,3.865 1.052,3.865 true 1.604,4.167 1.604,4.365 1.604,4.365 1.052,4.365 true 0.781,4.313 1,4.438 0.219,0.125 10 false MF 0.76,3.802 1,3.948 0.24,0.146 10 false MR 0.875,2.948 1.417,3.219 0.542,0.271 10 false *f 1.635,0.083 1.948,0.24 0.313,0.156 10 false *a 1.177,1.156 1.49,1.313 0.313,0.156 10 false *b 1.448,2.135 1.76,2.292 0.313,0.156 10 false *c 1.896,2.448 2.208,2.604 0.313,0.156 10 false *d 2.427,2.75 2.74,2.906 0.313,0.156 10 false *e 1.698,3.125 2.156,3.323 0.458,0.198 10 false z29
*a (A) Forward position
*b (B)
*c (C) Driving position
*d (D)
*e (E) Retracted position
*f Component without harness connected
(Outer Rear View Mirror Assembly LH)


Disconnect the outer rear view mirror assembly LH connector.


ii.

For each position: Disconnect the auxiliary battery, set the mirror position by hand, connect the auxiliary battery, and check the retractable mirror movement.

OK:
Tester Connection Condition Specified Condition

Click Location & Routing(z29)Location & Routing

Click Connector(z29)Body>other>Outer Rear View Mirror Assembly LH , Front Multiplex Network Door ECU LH

Auxiliary battery positive (+) - z29-3(MR)
Auxiliary battery negative (-) - z29-11(MF)
Forward position (A) Moves from (A) to (E)
Auxiliary battery positive (+) - z29-11(MF)
Auxiliary battery negative (-) - z29-3(MR)
Forward position (A) Does not move
Auxiliary battery positive (+) - z29-3(MR)
Auxiliary battery negative (-) - z29-11(MF)
Position between forward position (A) and driving position (C) Moves from (B) to (E)
Auxiliary battery positive (+) - z29-11(MF)
Auxiliary battery negative (-) - z29-3(MR)
Position between forward position (A) and driving position (C) Moves from (B) to (A)
Auxiliary battery positive (+) - z29-3(MR)
Auxiliary battery negative (-) - z29-11(MF)
Driving position (C) Moves from (C) to (E)
Auxiliary battery positive (+) - z29-11(MF)
Auxiliary battery negative (-) - z29-3(MR)
Driving position (C) Does not move
Auxiliary battery positive (+) - z29-3(MR)
Auxiliary battery negative (-) - z29-11(MF)
Position between driving position (C) and retracted position (E) Moves from (D) to (E)
Auxiliary battery positive (+) - z29-11(MF)
Auxiliary battery negative (-) - z29-3(MR)
Position between driving position (C) and retracted position (E) Moves from (D) to (C)
Auxiliary battery positive (+) - z29-3(MR)
Auxiliary battery negative (-) - z29-11(MF)
Retracted position (E) Does not move
Auxiliary battery positive (+) - z29-11(MF)
Auxiliary battery negative (-) - z29-3(MR)
Retracted position (E) Moves from (E) to (C)


If the result is not as specified, replace the outer rear view mirror assembly LH.



b.

Check the operation of the mirror surface.

i.
B199931C36
1.521,1.646 1.927,1.854 0.406,0.208 1.396,2.896 1.396,3.135 true 1.24,2.688 0.917,2.688 true 1.229,2.885 1,3.125 true 1.323,3.188 1.542,3.344 0.219,0.156 10 false M+ 1.615,1.677 1.917,1.823 0.302,0.146 10 false z29 0.823,3.167 1.052,3.302 0.229,0.135 10 false MH 0.146,1.531 0.771,1.917 0.625,0.385 10 false *a 0.677,2.625 0.896,2.771 0.219,0.146 10 false MV
*a Component without harness connected
(Outer Rear View Mirror Assembly LH)


Disconnect the outer rear view mirror assembly LH connector.


ii.

Apply auxiliary battery voltage and check the operation of the mirror.

OK:
Tester Connection Specified Condition

Click Location & Routing(z29)Location & Routing

Click Connector(z29)Body>other>Outer Rear View Mirror Assembly LH , Front Multiplex Network Door ECU LH

Auxiliary battery positive (+) - z29-1(MV)
Auxiliary battery negative (-) - z29-10(M+)
Turns upward
Auxiliary battery positive (+) - z29-10(M+)
Auxiliary battery negative (-) - z29-1(MV)
Turns downward
Auxiliary battery positive (+) - z29-10(M+)
Auxiliary battery negative (-) - z29-9(MH)
Turns inside
Auxiliary battery positive (+) - z29-9(MH)
Auxiliary battery negative (-) - z29-10(M+)
Turns outside


If the result is not as specified, replace the outer rear view mirror assembly LH.



c.

Check the side turn signal light assembly LH.

i.
B580872C21
1.448,0.26 1.969,0.5 0.521,0.24 2.135,1.531 2.365,1.531 2.365,1.531 2.365,1.698 true 1.604,2.01 1.604,1.594 true 2.333,1.75 2.625,1.99 0.292,0.24 10 false B 1.583,1.99 2.302,2.177 0.719,0.188 10 false - 0.104,0.156 0.313,0.365 0.208,0.208 10 false *a 1.594,0.323 1.885,0.563 0.292,0.24 10 false z29
*a Component without harness connected
(Outer Rear View Mirror Assembly LH)


Disconnect the outer rear view mirror assembly LH connector.


ii.

Apply auxiliary battery voltage to the terminals of the connector, and check the illumination condition.

OK:
Tester Connection Specified Condition

Click Location & Routing(z29)Location & Routing

Click Connector(z29)Body>other>Outer Rear View Mirror Assembly LH , Front Multiplex Network Door ECU LH

Auxiliary battery positive (+) - z29-16(B)
Auxiliary battery negative (-) - z29-12(-)
Side turn signal light illuminates


If the result is not as specified, inspect the side turn signal light assembly LH or replace the outer rear view mirror assembly LH.

Click hereVehicle Exterior>LIGHTING (EXT)>SIDE TURN SIGNAL LIGHT ASSEMBLY>INSPECTION



d.

Check the operation of the mirror heater.

i.
B580872C22
1.448,0.26 1.969,0.5 0.521,0.24 0.76,1.167 1.594,1.167 1.594,1.167 1.594,1.333 true 1.604,2.01 1.604,1.594 true 0.646,1.104 0.938,1.344 0.292,0.24 10 false + 1.583,1.99 2.302,2.177 0.719,0.188 10 false - 0.104,0.156 0.313,0.365 0.208,0.208 10 false *a 1.594,0.323 1.885,0.563 0.292,0.24 10 false z29
*a Component without harness connected
(Outer Rear View Mirror Assembly LH)


Disconnect the outer rear view mirror assembly LH connector.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(z29)Location & Routing

Click Connector(z29)Body>other>Outer Rear View Mirror Assembly LH , Front Multiplex Network Door ECU LH

z29-4(+) - z29-12(-) 25 °C (77 °F) 8.5 to 11.5 Ω



iii.

Connect the cable from the positive (+) auxiliary battery terminal to terminal 4 (+) and the negative (-) auxiliary battery terminal to terminal 12 (-), and then check that the mirror becomes warm.

HINT:

It takes a short time for the mirror to become warm.


OK:

Mirror becomes warm.


If the result is not as specified, inspect the outer mirror LH or replace the outer mirror actuator assembly LH.

Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR GLASS>INSPECTION



e.

Check the mirror light illumination.

i.
B580872C26
1.458,0.354 1.854,0.615 0.396,0.26 0.917,1.208 1.333,1.406 true 1.594,2.021 1.594,1.604 true 0.656,1.125 0.979,1.292 0.323,0.167 10 false MLP 1.573,2.021 1.729,2.177 0.156,0.156 10 false - 0.104,0.104 0.417,0.302 0.313,0.198 10 false *a 1.552,0.406 2.01,0.604 0.458,0.198 10 false z29
*a Component without harness connected
(Outer Rear View Mirror Assembly LH)


Disconnect the outer rear view mirror assembly LH connector.


ii.

Apply auxiliary battery voltage to the terminals of the connector, and check the illumination condition.

OK:
Tester Connection Specified Condition

Click Location & Routing(z29)Location & Routing

Click Connector(z29)Body>other>Outer Rear View Mirror Assembly LH , Front Multiplex Network Door ECU LH

Auxiliary battery positive (+) - z29-2(MLP)
Auxiliary battery negative (-) - z29-12(-)
Mirror light illuminates


If the result is not as specified, replace the outer rear view mirror assembly LH.



f.
B580872C27
1.458,0.354 1.854,0.615 0.396,0.26 2.583,1.167 2.125,1.344 true 1.594,2.021 1.594,1.604 true 2.667,1.094 3.125,1.25 0.458,0.156 10 false BSL 1.573,2.021 1.729,2.177 0.156,0.156 10 false - 0.104,0.104 0.417,0.302 0.313,0.198 10 false *a 1.552,0.406 2.01,0.604 0.458,0.198 10 false z29
*a Component without harness connected
(Outer Rear View Mirror Assembly LH)


Check the operation of the blind spot monitor indicator.

i.

Connect 4 new 1.5 V dry-cell batteries in series.


ii.

Apply 6 V dry-cell batteries to the terminals of the connector, and check the blind spot monitor indicator condition.

OK:
Tester Connection Specified Condition

Click Location & Routing(z29)Location & Routing

Click Connector(z29)Body>other>Outer Rear View Mirror Assembly LH , Front Multiplex Network Door ECU LH

Positive (+) end of the 6 V dry-cell battery - z29-8(BSL)
Negative (-) end of the 6 V dry-cell battery - z29-12(-)
Blind spot monitor indicator comes on


NOTICE:

Do not apply a voltage of more than 6 V.


If the result is not as specified, inspect the outer mirror LH or replace the outer rear view mirror assembly LH.

Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR GLASS>INSPECTION



Hide 87910 4.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH (w/ Reverse Shift-linked Mirror)

a.

Check the operation of the retractable mirror.

NOTICE:
·

Disconnect and reconnect the auxiliary battery between each mirror position check.

·

The mirror position cannot be changed manually when the auxiliary battery is connected. To change the mirror position manually, the auxiliary battery must be disconnected first.



i.
B237589C39
1.5,3.042 1.927,3.302 0.427,0.26 1.542,3.958 1.542,3.875 1.542,3.875 1,3.875 true 1.552,4.188 1.552,4.396 1.552,4.396 1.01,4.396 true 0.771,4.333 0.969,4.469 0.198,0.135 10 false MF 0.74,3.813 0.958,3.958 0.219,0.146 10 false MR 1.771,0.083 2.083,0.24 0.313,0.156 10 false *a 2.26,0.99 2.573,1.146 0.313,0.156 10 false *b 1.979,2.125 2.292,2.281 0.313,0.156 10 false *c 1.458,2.469 1.771,2.625 0.313,0.156 10 false *d 0.885,2.635 1.198,2.792 0.313,0.156 10 false *e 0.458,3.219 0.771,3.375 0.313,0.156 10 false *f 1.604,3.104 2.063,3.302 0.458,0.198 10 false z28
*a (A) Forward position
*b (B)
*c (C) Driving position
*d (D)
*e (E) Retracted position
*f Component without harness connected
(Outer Rear View Mirror Assembly RH)


Disconnect the outer rear view mirror assembly RH connector.


ii.

For each position: Disconnect the auxiliary battery, set the mirror position by hand, connect the auxiliary battery, and check the retractable mirror movement.

OK:
Tester Connection Condition Specified Condition

Click Location & Routing(z28)Location & Routing

Click Connector(z28)Body>other>Outer Rear View Mirror Assembly RH , Front Multiplex Network Door ECU RH

Auxiliary battery positive (+) - z28-3(MR)
Auxiliary battery negative (-) - z28-11(MF)
Forward position (A) Moves from (A) to (E)
Auxiliary battery positive (+) - z28-11(MF)
Auxiliary battery negative (-) - z28-3(MR)
Forward position (A) Does not move
Auxiliary battery positive (+) - z28-3(MR)
Auxiliary battery negative (-) - z28-11(MF)
Position between forward position (A) and driving position (C) Moves from (B) to (E)
Auxiliary battery positive (+) - z28-11(MF)
Auxiliary battery negative (-) - z28-3(MR)
Position between forward position (A) and driving position (C) Moves from (B) to (A)
Auxiliary battery positive (+) - z28-3(MR)
Auxiliary battery negative (-) - z28-11(MF)
Driving position (C) Moves from (C) to (E)
Auxiliary battery positive (+) - z28-11(MF)
Auxiliary battery negative (-) - z28-3(MR)
Driving position (C) Does not move
Auxiliary battery positive (+) - z28-3(MR)
Auxiliary battery negative (-) - z28-11(MF)
Position between driving position (C) and retracted position (E) Moves from (D) to (E)
Auxiliary battery positive (+) - z28-11(MF)
Auxiliary battery negative (-) - z28-3(MR)
Position between driving position (C) and retracted position (E) Moves from (D) to (C)
Auxiliary battery positive (+) - z28-3(MR)
Auxiliary battery negative (-) - z28-11(MF)
Retracted position (E) Does not move
Auxiliary battery positive (+) - z28-11(MF)
Auxiliary battery negative (-) - z28-3(MR)
Retracted position (E) Moves from (E) to (C)


If the result is not as specified, replace the outer rear view mirror assembly RH.



b.

Check the operation of the mirror surface.

i.
B199930C39
1.583,1.708 1.938,1.917 0.354,0.208 1.406,2.896 1.406,3.125 true 1.229,2.698 0.927,2.698 true 1.229,2.885 0.99,3.135 true 1.323,3.156 1.531,3.313 0.208,0.156 10 false M+ 0.698,2.646 0.917,2.781 0.219,0.135 10 false MV 0.813,3.167 1.042,3.313 0.229,0.146 10 false MH 0.292,1.583 0.938,2.156 0.646,0.573 10 false *a 1.656,1.74 2.115,1.938 0.458,0.198 10 false z28
*a Component without harness connected
(Outer Rear View Mirror Assembly RH)


Disconnect the outer rear view mirror assembly RH connector.


ii.

Apply auxiliary battery voltage and check the operation of the mirror.

OK:
Tester Connection Specified Condition

Click Location & Routing(z28)Location & Routing

Click Connector(z28)Body>other>Outer Rear View Mirror Assembly RH , Front Multiplex Network Door ECU RH

Auxiliary battery positive (+) - z28-1(MV)
Auxiliary battery negative (-) - z28-10(M+)
Turns upward
Auxiliary battery positive (+) - z28-10(M+)
Auxiliary battery negative (-) - z28-1(MV)
Turns downward
Auxiliary battery positive (+) - z28-9(MH)
Auxiliary battery negative (-) - z28-10(M+)
Turns inside
Auxiliary battery positive (+) - z28-10(M+)
Auxiliary battery negative (-) - z28-9(MH)
Turns outside


If the result is not as specified, replace the outer rear view mirror assembly RH.



c.

Check the side turn signal light assembly RH.

i.
B580872C23
1.458,0.354 1.854,0.615 0.396,0.26 2.104,2 2.104,1.583 true 1.594,2.021 1.594,1.604 true 2.083,2.01 2.25,2.177 0.167,0.167 10 false B 1.573,2.021 1.729,2.177 0.156,0.156 10 false - 0.104,0.104 0.417,0.302 0.313,0.198 10 false *a 1.552,0.406 2.01,0.604 0.458,0.198 10 false z28
*a Component without harness connected
(Outer Rear View Mirror Assembly RH)


Disconnect the outer rear view mirror assembly RH connector.


ii.

Apply auxiliary battery voltage to the terminals of the connector, and check the illumination condition.

OK:
Tester Connection Specified Condition

Click Location & Routing(z28)Location & Routing

Click Connector(z28)Body>other>Outer Rear View Mirror Assembly RH , Front Multiplex Network Door ECU RH

Auxiliary battery positive (+) - z28-16(B)
Auxiliary battery negative (-) - z28-12(-)
Side turn signal light illuminates


If the result is not as specified, inspect the side turn signal light assembly RH or replace the outer rear view mirror assembly RH.

Click hereVehicle Exterior>LIGHTING (EXT)>SIDE TURN SIGNAL LIGHT ASSEMBLY>INSPECTION



d.

Check the operation of the mirror heater.

i.
B580872C24
1.448,0.26 1.969,0.5 0.521,0.24 0.76,1.167 1.594,1.167 1.594,1.167 1.594,1.333 true 1.604,2.01 1.604,1.594 true 0.646,1.104 0.938,1.344 0.292,0.24 10 false + 1.583,1.99 2.302,2.177 0.719,0.188 10 false - 0.104,0.156 0.313,0.365 0.208,0.208 10 false *a 1.594,0.323 1.885,0.563 0.292,0.24 10 false z28
*a Component without harness connected
(Outer Rear View Mirror Assembly RH)


Disconnect the outer rear view mirror assembly RH connector.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(z28)Location & Routing

Click Connector(z28)Body>other>Outer Rear View Mirror Assembly RH , Front Multiplex Network Door ECU RH

z28-4(+) - z28-12(-) 25 °C (77 °F) 8.5 to 11.5 Ω



iii.

Connect the cable from the positive (+) auxiliary battery terminal to terminal 9 (+) and the negative (-) auxiliary battery terminal to terminal 10 (-), and then check that the mirror becomes warm.

HINT:

It takes a short time for the mirror to become warm.


OK:

Mirror becomes warm.


If the result is not as specified, inspect the outer mirror RH or replace the outer mirror actuator assembly RH.

Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR GLASS>INSPECTION



e.

Check the mirror light illumination.

i.
B580872C25
1.458,0.354 1.854,0.615 0.396,0.26 0.917,1.208 1.333,1.406 true 1.594,2.021 1.594,1.604 true 0.656,1.125 0.979,1.292 0.323,0.167 10 false MLP 1.573,2.021 1.729,2.177 0.156,0.156 10 false - 0.104,0.104 0.417,0.302 0.313,0.198 10 false *a 1.552,0.406 2.01,0.604 0.458,0.198 10 false z28
*a Component without harness connected
(Outer Rear View Mirror Assembly RH)


Disconnect the outer rear view mirror assembly RH connector.


ii.

Apply auxiliary battery voltage to the terminals of the connector, and check the illumination condition.

OK:
Tester Connection Specified Condition

Click Location & Routing(z28)Location & Routing

Click Connector(z28)Body>other>Outer Rear View Mirror Assembly RH , Front Multiplex Network Door ECU RH

Auxiliary battery positive (+) - z28-2(MLP)
Auxiliary battery negative (-) - z28-12(-)
Mirror light illuminates


If the result is not as specified, replace the outer rear view mirror assembly RH.



f.
B580872C28
1.458,0.354 1.854,0.615 0.396,0.26 2.583,1.167 2.125,1.344 true 1.594,2.021 1.594,1.604 true 2.667,1.094 3.125,1.25 0.458,0.156 10 false BSR 1.573,2.021 1.729,2.177 0.156,0.156 10 false - 0.104,0.104 0.417,0.302 0.313,0.198 10 false *a 1.552,0.406 2.01,0.604 0.458,0.198 10 false z28
*a Component without harness connected
(Outer Rear View Mirror Assembly RH)


Check the operation of the blind spot monitor indicator.

i.

Connect 4 new 1.5 V dry-cell batteries in series.


ii.

Apply 6 V dry-cell batteries to the terminals of the connector, and check the blind spot monitor indicator condition.

OK:
Tester Connection Specified Condition

Click Location & Routing(z28)Location & Routing

Click Connector(z28)Body>other>Outer Rear View Mirror Assembly RH , Front Multiplex Network Door ECU RH

Positive (+) end of the 6 V dry-cell battery - z28-8(BSR)
Negative (-) end of the 6 V dry-cell battery - z28-12(-)
Blind spot monitor indicator comes on


NOTICE:

Do not apply a voltage of more than 6 V.


If the result is not as specified, inspect the outer mirror RH or replace the outer rear view mirror assembly RH.

Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR GLASS>INSPECTION