Home › Power Source / Network › POWER DISTRIBUTION › INTEGRATION RELAY (for Rear Side)
RM37H0E _57 Power Source / Network _095301 POWER DISTRIBUTION _0448298 INTEGRATION RELAY(for Rear Side) A

POWER DISTRIBUTION  INTEGRATION RELAY(for Rear Side)  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
E450303N02
6.406,0.271 6.74,0.271 false 6.438,0.677 6.698,0.677 false 4.813,1.604 5.531,1.604 false 5.656,2.74 6.188,2.74 false 5.979,4.948 5.979,5.406 false 1.781,3.031 1.667,3.479 1.667,3.479 1.427,3.479 false 3.542,4.521 3.542,4.979 false 1.865,4.781 1.24,4.781 false 5.979,3.781 6.51,3.781 false 6.25,0.156 6.531,0.51 0.281,0.354 18 false 1 6.26,0.542 6.542,0.896 0.281,0.354 18 false 2 6.26,2.604 6.542,2.958 0.281,0.354 18 false 3 6.604,3.646 6.885,4 0.281,0.354 18 false 4 5.604,1.448 5.885,1.802 0.281,0.354 18 false 5 5.938,5.448 6.219,5.802 0.281,0.354 18 false 6 3.49,5.042 3.771,5.396 0.281,0.354 18 false 7 1.052,4.646 1.333,5 0.281,0.354 18 false 8 1.26,3.313 1.542,3.667 0.281,0.354 18 false 9 4.708,3.083 5.021,3.281 0.313,0.198 10 false x2 3.979,1.031 4.292,1.229 0.313,0.198 10 false x 5 2.729,4.219 3.042,4.417 0.313,0.198 10 false x 2 5.281,1.958 5.594,2.156 0.313,0.198 10 false x 2

Procedure Part Name Code
Z101186

Z101188

Z101187

1 PRECAUTION - (Click here) - -
2 CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL - - - -
3 LUGGAGE COMPARTMENT MAT SUB-ASSEMBLY 64701 - - -
4 TOOL BOX 75201A - - -
5 FRONT LUGGAGE COMPARTMENT TRIM COVER 64075B - - -
6 REAR FLOOR FINISH PLATE 58387 - - -
7 LUGGAGE COMPARTMENT TRIM COVER LH 64715D - - -
8 INNER LUGGAGE COMPARTMENT TRIM COVER LH 64722 - - -
9 NO. 2 SEMICONDUCTOR POWER INTEGRATION ECU 82644B (Click here) - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the No. 2 semiconductor power integration ECU removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary procedures Effect/Inoperative Function when Necessary Procedure not Performed Link
Disconnect cable from negative (-) auxiliary battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)

HINT:
·

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

-

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Adaptive high beam system

-

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Air conditioning system After the ignition switch is turned to ON, the servo motor and expansion valve standard position is recognized. -


·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 1. PRECAUTION

Z101186

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click here(Click here)



Hide 2.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 64701 3.REMOVE LUGGAGE COMPARTMENT MAT SUB-ASSEMBLY

Hide 64075B 5.REMOVE FRONT LUGGAGE COMPARTMENT TRIM COVER

Hide 58387 6.REMOVE REAR FLOOR FINISH PLATE

Hide 64715D 7.REMOVE LUGGAGE COMPARTMENT TRIM COVER LH

Hide 64722 8.REMOVE INNER LUGGAGE COMPARTMENT TRIM COVER LH

Hide 82644B 9.REMOVE NO. 2 SEMICONDUCTOR POWER INTEGRATION ECU

Z101186

NOTICE:
·

Make sure the connector terminal is free from oil and grease.

·

Do not disassemble the No. 2 semiconductor power integration ECU.




a.
E450304C02
0.656,0.125 0.833,0.396 0.177,0.271 18 true i 4.26,0.906 4.417,1.177 0.156,0.271 18 true ii 6.115,0.115 6.323,0.365 0.208,0.25 18 true iii
V113147

Remove in this Direction - -


i.

Remove the nut, detach the guide and remove the No. 2 semiconductor power integration ECU.


ii.

Disconnect the power source connector.

NOTICE:

First disconnect the power supply connector.



iii.

Using a thin-bladed screwdriver with its tip wrapped with protective tape, detach the claw and disconnect the lever connector.