Home › Vehicle Interior › LIGHTING (INT) › LIGHTING SYSTEM
RM37H0E _58 Vehicle Interior _095306 LIGHTING (INT) _0448415 LIGHTING SYSTEM J

LIGHTING (INT)  LIGHTING SYSTEM  Ambient Illumination Light Circuit  


DESCRIPTION

The main body ECU (multiplex network body ECU) controls the operation of the No. 1 interior illumination light assembly (cup holder illumination).

WIRING DIAGRAM

E456342E02
5.76,0.813 6.375,1.01 0.615,0.198 10 false LED1 5.448,0.802 5.76,1 0.313,0.198 10 false 20 2.406,1.51 2.719,1.708 0.313,0.198 10 false D9 2.99,0.948 3.146,1.146 0.156,0.198 10 false B 2.75,0.781 2.906,0.979 0.156,0.198 10 false 2 4.313,0.938 4.469,1.135 0.156,0.198 10 false E 4.583,0.813 4.74,1.01 0.156,0.198 10 false 1 2.417,1.688 4.917,2.021 2.5,0.333 10 false No. 1 Interior Illumination Light Assembly (Cup Holder Illumination) 1.948,1.073 2.563,1.271 0.615,0.198 10 false DOME P 0.323,0.906 1.219,1.323 0.896,0.417 10 false from Auxiliary Battery 5.396,1.719 5.854,1.917 0.458,0.198 10 false D14 5.406,1.865 7.063,2.26 1.656,0.396 10 false Main Body ECU (Multiplex Network Body ECU)

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.



PROCEDURE

1.PERFORM ACTIVE TEST USING GTS
a.

Perform the Active Test according to the display on the GTS.

Body Electrical > Main Body > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Interior Illumination Light1 Illuminates the following lights:
·

No. 1 interior illumination light assembly (cup holder illumination)


OFF or ON -
Body Electrical > Main Body > Active Test
Tester Display
Interior Illumination Light1
50004 123 68
OK:

No. 1 interior illumination light assembly (cup holder illumination) are illuminate.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT NO. 1 INTERIOR ILLUMINATION LIGHT ASSEMBLY (CUP HOLDER ILLUMINATION)
2.INSPECT NO. 1 INTERIOR ILLUMINATION LIGHT ASSEMBLY (CUP HOLDER ILLUMINATION)

OK

3.CHECK HARNESS AND CONNECTOR (NO. 1 INTERIOR ILLUMINATION LIGHT ASSEMBLY [CUP HOLDER ILLUMINATION] - BATTERY)

NG

REPLACE NO. 1 INTERIOR ILLUMINATION LIGHT ASSEMBLY (CUP HOLDER ILLUMINATION)

3.CHECK HARNESS AND CONNECTOR (NO. 1 INTERIOR ILLUMINATION LIGHT ASSEMBLY [CUP HOLDER ILLUMINATION] - BATTERY)
a.

Disconnect the D9 No. 1 interior illumination light assembly (cup holder illumination) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(D9)Location & Routing

Click Connector(D9)Instrument Panel>Instrument Panel Wire>Cup Holder Illumination (No. 1 Interior Illumination Light Assembly)

D9-2 (B) - Body ground Ignition switch off 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (NO. 1 INTERIOR ILLUMINATION LIGHT ASSEMBLY [CUP HOLDER ILLUMINATION] - MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU])

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (NO. 1 INTERIOR ILLUMINATION LIGHT ASSEMBLY [CUP HOLDER ILLUMINATION] - MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU])
a.

Disconnect the D9 No. 1 interior illumination light assembly (cup holder illumination) connector.


b.

Disconnect the D14 main body ECU (multiplex network body ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D9,D14)Location & Routing

Click Connector(D9)Instrument Panel>Instrument Panel Wire>Cup Holder Illumination (No. 1 Interior Illumination Light Assembly)

Click Connector(D14)Instrument Panel>Instrument Panel Wire>Main Body ECU

D9-1 (E) - D14-20 (LED1) Always Below 1 Ω
D9-1 (E) or D14-20 (LED1) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR