Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM › 2020.11–2021.08
RM37H0E _59 Vehicle Exterior _093353 LIGHTING (EXT) _0448416 LIGHTING SYSTEM C

LIGHTING (EXT)  LIGHTING SYSTEM  B242E  Open in IG Circuit  


DESCRIPTION

The headlight ECU sub-assembly operates using the power source voltage input from the IG terminal and ECUB terminal.

The IG terminal power source voltage is supplied by turning the IG1 relay to ON.

The headlight ECU sub-assembly receives ignition switch ON signals from the main body ECU (multiplex network body ECU) via CAN communication, compares the ignition switch ON signal and the power source voltage supply condition of the IG terminal and monitors the result.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority Note
B242E Open in IG Circuit
Detection condition:

Ignition switch ON


Malfunction status:

When the IG terminal power source voltage is 0 V (ignition switch off), IG ON signals from the main body ECU (multiplex network body ECU) via CAN communication are continuously received


Malfunction duration:

10 seconds or more


·

Headlight ECU sub-assembly LH

·

Harness or connector


AFS A w/ Adaptive High Beam System

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority Note
B242E Open in IG Circuit
Detection condition:

Ignition switch ON


Malfunction status:

When the IG terminal power source voltage is 0 V (ignition switch off), IG ON signals from the main body ECU (multiplex network body ECU) via CAN communication are continuously received


Malfunction duration:

10 seconds or more


·

Headlight ECU sub-assembly RH

·

Harness or connector


AFS (Sub) A w/ Adaptive High Beam System

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority Note
B242E Open in IG Circuit
Detection condition:

Ignition switch ON


Malfunction status:

When the IG terminal power source voltage is 0 V (ignition switch off), IG ON signals from the main body ECU (multiplex network body ECU) via CAN communication are continuously received


Malfunction duration:

10 seconds or more


·

Headlight ECU sub-assembly LH

·

Harness or connector


HL AutoLeveling A w/o Adaptive High Beam System

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority Note
B242E Open in IG Circuit
Detection condition:

Ignition switch ON


Malfunction status:

When the IG terminal power source voltage is 0 V (ignition switch off), IG ON signals from the main body ECU (multiplex network body ECU) via CAN communication are continuously received


Malfunction duration:

10 seconds or more


·

Headlight ECU sub-assembly RH

·

Harness or connector


HL AutoLeveling (Sub) A w/o Adaptive High Beam System

WIRING DIAGRAM

E361140E06
4.729,1.927 7.146,2.188 2.417,0.26 10 false A26 4.719,2.083 7.135,2.344 2.417,0.26 10 false Headlight ECU Sub-assembly LH 4.625,4.146 7.042,4.406 2.417,0.26 10 false A27 4.625,4.333 7.104,4.625 2.479,0.292 10 false Headlight ECU Sub-assembly RH 5.219,3.563 5.771,3.885 0.552,0.323 10 false GND 5.208,1.344 5.76,1.667 0.552,0.323 10 false GND 5.208,0.677 5.76,1 0.552,0.323 10 false IG 5.208,2.917 5.76,3.24 0.552,0.323 10 false IG 5,2.844 5.552,3.167 0.552,0.323 10 false 4 4.938,3.479 5.49,3.802 0.552,0.323 10 false 12 4.938,1.26 5.49,1.583 0.552,0.323 10 false 12 4.99,0.635 5.542,0.958 0.552,0.323 10 false 4 3.667,3.146 4.594,3.531 0.927,0.385 10 false R/B-IG1 NO.1 1.563,2.906 2.792,3.198 1.229,0.292 10 false from IG1 Relay 3.635,0.917 4.563,1.302 0.927,0.385 10 false R/B-IG1 NO.1 1.583,0.688 2.813,0.979 1.229,0.292 10 false from IG1 Relay

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

If the headlight ECU sub-assembly LH has been replaced, it is necessary to synchronize the vehicle information and initialize the headlight ECU sub-assembly LH.

Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>REGISTRATION



PROCEDURE

1.CHECK VEHICLE TYPE
a.

Check vehicle condition.


Result:
Result Proceed to
w/ Adaptive High Beam System A
w/o Adaptive High Beam System B



A

2.CLEAR DTC

B

8.CLEAR DTC
2.CLEAR DTC

Pre-procedure1

a.

None


Procedure1

a.

Clear the DTCs.

Body Electrical > AFS > Clear DTCs
50002 165
Body Electrical > AFS (Sub) > Clear DTCs
50002 413
Result:
Proceed to
NEXT



Post-procedure1

a.

None



NEXT

3.CHECK FOR DTC
3.CHECK FOR DTC

Pre-procedure1

a.

Turn the ignition switch ON and wait for at least 10 seconds or more.


Procedure1

a.

Check for DTCs.

Body Electrical > AFS > Trouble Codes
50001 165
Body Electrical > AFS (Sub) > Trouble Codes
50001 413
Result:
Result Proceed to
Only B242E for AFS is output A
Only B242E for AFS (Sub) is output B
None of the above conditions are met C



Malfunction Content System Relevant DTC
Headlight ECU sub-assembly LH AFS B242E Open in IG Circuit
Headlight ECU sub-assembly RH AFS (Sub) B242E Open in IG Circuit

Post-procedure1

a.

None



A

4.CHECK HARNESS AND CONNECTOR (HEADLIGHT ECU SUB-ASSEMBLY LH - BATTERY AND BODY GROUND)

B

6.CHECK HARNESS AND CONNECTOR (HEADLIGHT ECU SUB-ASSEMBLY RH - BATTERY AND BODY GROUND)

C

4.CHECK HARNESS AND CONNECTOR (HEADLIGHT ECU SUB-ASSEMBLY LH - BATTERY AND BODY GROUND)

Pre-procedure1

a.

Disconnect the A26 headlight ECU sub-assembly LH connector.


Procedure1

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(A26)Location & Routing

Click Connector(A26)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Headlight ECU Sub-Assembly LH

A26-4 (IG) - Body ground Ignition switch ON 11 to 14 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

5.CHECK HARNESS AND CONNECTOR (HEADLIGHT ECU SUB-ASSEMBLY LH - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (HEADLIGHT ECU SUB-ASSEMBLY LH - BATTERY AND BODY GROUND)

Pre-procedure1

a.

Disconnect the A26 headlight ECU sub-assembly LH connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A26)Location & Routing

Click Connector(A26)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Headlight ECU Sub-Assembly LH

A26-12 (GND) - Body ground Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE HEADLIGHT ECU SUB-ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (HEADLIGHT ECU SUB-ASSEMBLY RH - BATTERY AND BODY GROUND)

Pre-procedure1

a.

Disconnect the A27 headlight ECU sub-assembly RH connector.


Procedure1

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(A27)Location & Routing

Click Connector(A27)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Headlight ECU Sub-Assembly RH

A27-4 (IG) - Body ground Ignition switch ON 11 to 14 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

7.CHECK HARNESS AND CONNECTOR (HEADLIGHT ECU SUB-ASSEMBLY RH - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (HEADLIGHT ECU SUB-ASSEMBLY RH - BATTERY AND BODY GROUND)

Pre-procedure1

a.

Disconnect the A27 headlight ECU sub-assembly RH connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A27)Location & Routing

Click Connector(A27)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Headlight ECU Sub-Assembly RH

A27-12 (GND) - Body ground Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE HEADLIGHT ECU SUB-ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CLEAR DTC

Pre-procedure1

a.

None


Procedure1

a.

Clear the DTCs.

Body Electrical > HL AutoLeveling > Clear DTCs
50002 361
Body Electrical > HL AutoLeveling (Sub) > Clear DTCs
50002 414
Result:
Proceed to
NEXT



Post-procedure1

a.

None



NEXT

9.CHECK FOR DTC
9.CHECK FOR DTC

Pre-procedure1

a.

Turn the ignition switch ON and wait for at least 10 seconds or more.


Procedure1

a.

Check for DTCs.

Body Electrical > HL AutoLeveling > Trouble Codes
50001 361
Body Electrical > HL AutoLeveling (Sub) > Trouble Codes
50001 414
Result:
Result Proceed to
Only B242E for HL AutoLeveling is output A
Only B242E for HL AutoLeveling (Sub) is output B
None of the above conditions are met C



Malfunction Content System Relevant DTC
Headlight ECU sub-assembly LH HL AutoLeveling B242E Open in IG Circuit
Headlight ECU sub-assembly RH HL AutoLeveling (Sub) B242E Open in IG Circuit

Post-procedure1

a.

None



A

5.CHECK HARNESS AND CONNECTOR (HEADLIGHT ECU SUB-ASSEMBLY LH - BATTERY AND BODY GROUND)

B

7.CHECK HARNESS AND CONNECTOR (HEADLIGHT ECU SUB-ASSEMBLY RH - BATTERY AND BODY GROUND)

C