The headlight ECU sub-assembly stores this DTC if it detects an internal malfunction related to the CAN communication system.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from | Priority | Note |
|---|---|---|---|---|---|---|
| U1000 | CAN Communication Failure (Message Registry) | CAN communication failure | Headlight ECU sub-assembly LH | AFS | A | w/ Adaptive High Beam System |
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from | Priority | Note |
|---|---|---|---|---|---|---|
| U1000 | CAN Communication Failure (Message Registry) | CAN communication failure | Headlight ECU sub-assembly RH | AFS (Sub) | A | w/ Adaptive High Beam System |
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from | Priority | Note |
|---|---|---|---|---|---|---|
| U1000 | CAN Communication Failure (Message Registry) | CAN communication failure | Headlight ECU sub-assembly LH | HL AutoLeveling | A | w/o Adaptive High Beam System |
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from | Priority | Note |
|---|---|---|---|---|---|---|
| U1000 | CAN Communication Failure (Message Registry) | CAN communication failure | Headlight ECU sub-assembly RH | HL AutoLeveling (Sub) | A | w/o Adaptive High Beam System |
If the headlight ECU sub-assembly LH has been replaced, it is necessary to synchronize the vehicle information and initialize the headlight ECU sub-assembly LH.
Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>REGISTRATION
Check vehicle condition.
| Result | Proceed to |
|---|---|
| w/ Adaptive High Beam System | A |
| w/o Adaptive High Beam System | B |
A
B
Pre-procedure1
None
Procedure1
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
Post-procedure1
None
NEXT
Pre-procedure1
Turn the ignition switch to ON.
Procedure1
Check for DTCs.
| Result | Proceed to |
|---|---|
| Only U1000 for AFS is output | A |
| Only U1000 for AFS (Sub) is output | B |
| None of the above conditions are met | C |
| Malfunction Content | System | Relevant DTC | |
|---|---|---|---|
| Headlight ECU sub-assembly LH | AFS | U1000 | CAN Communication Failure (Message Registry) |
| Headlight ECU sub-assembly RH | AFS (Sub) | U1000 | CAN Communication Failure (Message Registry) |
Post-procedure1
None
A
B
C
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
Pre-procedure1
None
Procedure1
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
Post-procedure1
None
NEXT
Pre-procedure1
Turn the ignition switch to ON.
Procedure1
Check for DTCs.
| Result | Proceed to |
|---|---|
| Only U1000 for HL AutoLeveling is output | A |
| Only U1000 for HL AutoLeveling is output | B |
| None of the above conditions are met | C |
| Malfunction Content | System | Relevant DTC | |
|---|---|---|---|
| Headlight ECU sub-assembly LH | HL AutoLeveling | U1000 | CAN Communication Failure (Message Registry) |
| Headlight ECU sub-assembly RH | HL AutoLeveling (Sub) | U1000 | CAN Communication Failure (Message Registry) |
Post-procedure1
None
A
B
C
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING