Home › ADAS / AD › ADVANCED DRIVER ASSISTANCE SYSTEM › ADAPTIVE HIGH BEAM SYSTEM › 2020.11–2021.08
RM37H0E _95 ADAS / AD _095317 ADVANCED DRIVER ASSISTANCE SYSTEM _0448417 ADAPTIVE HIGH BEAM SYSTEM C

ADVANCED DRIVER ASSISTANCE SYSTEM  ADAPTIVE HIGH BEAM SYSTEM  B2490  Left LED Fan Circuit  B2491  Right LED Fan Circuit  


DESCRIPTION

The light control LED ECU receives adaptive high beam system control signals from the headlight ECU sub-assembly via LIN communication and operates the additional fan to cool the LED in order to prevent overheating of the additional LEDs.

When the low beam headlight is illuminated, it continuously operates the additional fan.

The light control LED ECU uses pulse signals from the FANP terminal to monitor additional fan rotation signals, and when it detects a malfunction, it sends a signal to the headlight ECU sub-assembly via LIN communication.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
B2490 Left LED Fan Circuit
Detection condition:

Ignition switch is ON and low beam headlight is illuminated


Malfunction status:

Additional fan malfunction signals are received from light control LED ECU LH


Malfunction duration:

-


·

Headlight unit assembly LH

·

Headlight unit LH (LED array fan LH)

·

Light control LED ECU LH


AFS A
B2491 Right LED Fan Circuit
Detection Condition:

Ignition switch is ON and low beam headlight is illuminated


Malfunction Status:

Additional fan malfunction signals are received from light control LED ECU RH


Malfunction duration:

-


·

Headlight unit assembly RH

·

Headlight unit RH (LED array fan RH)

·

Light control LED ECU RH


AFS A

WIRING DIAGRAM

E377928E07
5.188,4.073 7.094,4.406 1.906,0.333 10 false Headlight ECU Sub-assembly 0.677,4.354 2.875,4.656 2.198,0.302 10 false : LIN Communication Line 3.146,1.448 3.885,1.823 0.74,0.375 10 false 11 3.198,1.688 3.938,2.063 0.74,0.375 10 false 9 0.635,2.844 2.323,3.156 1.688,0.313 10 false L 3.531,2.823 5.219,3.135 1.688,0.313 10 false K 3.156,1.917 3.896,2.292 0.74,0.375 10 false 10 2.073,1.469 2.813,1.844 0.74,0.375 10 false 10 2.052,1.708 2.792,2.083 0.74,0.375 10 false 11 2.063,1.917 2.802,2.292 0.74,0.375 10 false 20 2.292,3.74 4.219,4.042 1.927,0.302 10 false Headlight Unit Assembly 3.948,1.177 4.688,1.552 0.74,0.375 10 false 5 V 0.854,2.323 2.542,2.635 1.688,0.313 10 false Array Fan 4.688,1.719 5.427,2.094 0.74,0.375 10 false IC 4.25,1.406 4.99,1.781 0.74,0.375 10 false 5 V 3.531,2.99 5.208,3.385 1.677,0.396 10 false Light Control LED ECU 0.646,3 2.333,3.313 1.688,0.313 10 false Headlight Unit


PROCEDURE

1.CHECK FOR DTC

Pre-procedure1

a.

Clear the DTCs.

Body Electrical > AFS > Clear DTCs
50002 165

b.

Turning the ignition switch to ON and illuminating the low beam headlights using the light control switch.


Procedure1

a.

Check for DTCs.

Body Electrical > AFS > Trouble Codes
50001 165
Result:
Result Proceed to
B2490 and B2491 are not output A
B2490 is output B
B2491 is output C



Post-procedure1

a.

None



A

B

2.INSPECT HEADLIGHT UNIT ASSEMBLY LH

C

4.INSPECT HEADLIGHT UNIT ASSEMBLY RH
2.INSPECT HEADLIGHT UNIT ASSEMBLY LH

Pre-procedure1

a.

Remove the headlight unit LH.

HINT:

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY>DISASSEMBLY


E462606C03
1.854,0.719 2.198,0.979 0.344,0.26 4.99,0.719 5.333,0.979 0.344,0.26 1.073,0.677 1.385,0.875 0.313,0.198 10 false *a 4.24,0.698 4.552,0.896 0.313,0.198 10 false *b 5.125,0.802 5.438,1 0.313,0.198 10 false L 1.979,0.771 2.292,0.969 0.313,0.198 10 false K
*a Component without harness connected
(Light Control LED ECU LH)
*b Component without harness connected
(Headlight Unit LH)



Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K-11 - L-1 Always Below 1 Ω
K-9 - L-2 Always Below 1 Ω
K-10 - L-3 Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

3.CHECK LIGHT CONTROL LED ECU LH

NG

REPLACE HEADLIGHT UNIT ASSEMBLY LH

3.CHECK LIGHT CONTROL LED ECU LH

Pre-procedure1

a.
E462607C03
1.542,0.469 1.969,0.719 0.427,0.25 1.719,0.531 1.875,0.729 0.156,0.198 10 false L 0.771,0.396 1.094,0.656 0.323,0.26 10 false *a
*a Component without harness connected
(Headlight Unit LH)


Remove the headlight unit LH.

HINT:

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY>DISASSEMBLY



b.

Reconnect the headlight ECU sub-assembly LH connectors.


c.

Reconnect the light control LED ECU LH connectors.


Procedure1

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
L-10 - L-20 Low beam headlights illuminated 4.75 to 5.25 V
L-11 - L-20 Low beam headlights illuminated 4.75 to 5.25 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

NG

REPLACE LIGHT CONTROL LED ECU LH

4.INSPECT HEADLIGHT UNIT ASSEMBLY RH

Pre-procedure1

a.

Remove the headlight unit RH.

HINT:

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY>DISASSEMBLY


E462606C03
1.854,0.719 2.198,0.979 0.344,0.26 4.99,0.719 5.333,0.979 0.344,0.26 1.073,0.677 1.385,0.875 0.313,0.198 10 false *a 4.24,0.698 4.552,0.896 0.313,0.198 10 false *b 5.125,0.802 5.438,1 0.313,0.198 10 false L 1.979,0.771 2.292,0.969 0.313,0.198 10 false K
*a Component without harness connected
(Light Control LED ECU RH)
*b Component without harness connected
(Headlight Unit RH)



Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K-11 - L-1 Always Below 1 Ω
K-9 - L-2 Always Below 1 Ω
K-10 - L-3 Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

5.CHECK LIGHT CONTROL LED ECU RH

NG

REPLACE HEADLIGHT UNIT ASSEMBLY RH

5.CHECK LIGHT CONTROL LED ECU RH

Pre-procedure1

a.
E462607C03
1.542,0.469 1.969,0.719 0.427,0.25 1.719,0.531 1.875,0.729 0.156,0.198 10 false L 0.771,0.396 1.094,0.656 0.323,0.26 10 false *a
*a Component without harness connected
(Headlight Unit RH)


Remove the headlight unit RH.

HINT:

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY>DISASSEMBLY



b.

Reconnect the headlight ECU sub-assembly RH connectors.


c.

Reconnect the light control LED ECU RH connectors.


Procedure1

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
L-10 - L-20 Low beam headlights illuminated 4.75 to 5.25 V
L-11 - L-20 Low beam headlights illuminated 4.75 to 5.25 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

NG

REPLACE LIGHT CONTROL LED ECU RH