CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) AND DRIVER SIDE JUNCTION BLOCK ASSEMBLY
| *1 | Main body ECU (multiplex network body ECU) | - | - |
Remove the main body ECU (multiplex network body ECU) from the driver side junction block assembly.
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL
Connect the driver side junction block assembly connectors.
Measure the voltage and resistance according to the value(s) in the table below.
| Tester Connection | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| A-11 (GND1) - Body ground | Ground | Always | Below 1 Ω |
| A-30 (ACC) - Body ground | ACC power supply | Ignition switch to ACC | 11 to 14 V |
| Ignition switch off | Below 1 V | ||
| A-31 (BECU) - Body ground | Auxiliary battery power supply | Ignition switch off | 11 to 14 V |
| A-32 (IG) - Body ground | IG power supply | Ignition switch to ON | 11 to 14 V |
| Ignition switch off | Below 1 V | ||
| D11-1 (FLCY) - Body ground | Front door courtesy light switch assembly LH input signal | Front door LH closed (OFF) → open (ON) | 10 kΩ or higher → Below 1 Ω |
| D11-6 (FRCY) - Body ground | Front door courtesy light switch assembly RH input signal | Front door RH closed (OFF) → open (ON) | 10 kΩ or higher → Below 1 Ω |
| A-13 (LCTY) - Body ground | Rear door courtesy light switch assembly LH input signal | Rear door LH closed (OFF) → open (ON) | 10 kΩ or higher → Below 1 Ω |
| A-2 (RCTY) - Body ground | Rear door courtesy light switch assembly RH input signal | Rear door RH closed (OFF) → open (ON) | 10 kΩ or higher → Below 1 Ω |
| A-4 (LGCY) - Body ground | Luggage compartment door courtesy light switch signal | Luggage compartment door closed (OFF) → open (ON) | 10 kΩ or higher → Below 1 Ω |
| D11-30 (HCTY) - Body ground | Engine hood courtesy switch input signal | Engine hood open (OFF) → closed (ON) | 10 kΩ or higher → Below 1 Ω |
Install the main body ECU (multiplex network body ECU) to the driver side junction block assembly.
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>INSTALLATION
Measure the voltage and check for pulses according to the value(s) in the table below.
| Tester Connection | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| 4H-31 (LSFL) - Body ground*1
4A-15 (LSFL) - Body ground*2 |
Front door LH unlock detection switch input signal | Front door LH unlocked | Below 1 V |
| Ignition switch off, all doors closed and front door LH locked | Pulse generation | ||
| 4D-14 (LSFR) - Body ground*1
4H-31 (LSFR) - Body ground*2 |
Front door RH unlock detection switch input signal | Front door RH unlocked | Below 1 V |
| Ignition switch off, all doors closed and front door RH locked | Pulse generation | ||
| 4H-21 (LSWL) - Body ground*1
4D-12 (LSWL) - Body ground*2 |
Rear door LH unlock detection switch input signal | Rear door LH unlocked | Below 1 V |
| Ignition switch off, all doors closed and rear door LH locked | Pulse generation | ||
| D12-20 (LSWR) - Body ground | Rear door RH unlock detection switch input signal | Rear door RH unlocked | Below 1 V |
| Ignition switch off, all doors closed and rear door RH locked | Pulse generation | ||
| D14-12 (SSCL) - Body ground | Theft warning siren assembly drive | Theft warning siren assembly sounding (Theft deterrent system is in alarm sounding state) | Pulse generation (Below 1 V ←→ 11 to 14 V) |
| D14-3 (SSW1) - Body ground | Intrusion sensor cancel switch signal | Intrusion sensor cancel switch on | Below 1 V |
| Intrusion sensor cancel switch off | Pulse generation | ||
| D14-14 (ISIF) - Body ground | Theft warning ultrasonic and tilt sensor signal input | ·
No moving object detected by sensor ·
Vehicle tilt not detected by sensor |
11 to 14 V |
| Theft deterrent system changes from disarmed state to armed preparation state | Pulse generation
(See Waveform 1) |
||
| Any of the following conditions is met when the theft deterrent system is in armed preparation state
·
Any moving object detected by sensor ·
Vehicle tilt detected by sensor |
Pulse generation | ||
| 4F-16 (HORN) - Body ground*1
4F-28 (HORN) - Body ground*2 |
Vehicle horn drive | Vehicle horns sounding (Theft deterrent system is in alarm sounding state) | Pulse generation (Below 1 V ←→ 11 to 14 V) |
*1: for LHD
*2: for RHD
Using an oscilloscope, check the waveform.
The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.
Waveform 1 (Reference)
| *a | IOUT Initial Signal | *b | IOUT Initial Response |
| *c | Approximately 1.0 Second | *d | Initial Diagnosis |
| *e | Approximately 1.0 to 1.6 Seconds | *f | Approximately 0.05 Seconds |
| *g | Approximately 5.5 Seconds | *h | Disarmed State |
| *i | Arming Preparation State | - | - |
| Item | Content |
|---|---|
| Tester Connection | D14-14 (ISIF) - Body ground |
| Tool Setting | 2 V/DIV., 100 ms./DIV. |
| Condition | Theft deterrent system changes from disarmed state to armed preparation state |