Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM
RM37H0E _58 Vehicle Interior _095303 THEFT DETERRENT / KEYLESS ENTRY _0448454 THEFT DETERRENT SYSTEM C

THEFT DETERRENT / KEYLESS ENTRY  THEFT DETERRENT SYSTEM  B2762  Intrusion Sensor Signal Circuit Malfunction  


DESCRIPTION

The theft warning ultrasonic and tilt sensor conducts self-diagnosis immediately after power is supplied to the sensor (when the theft deterrent system is set).

If a malfunction is detected in the ISIF line, the main body ECU (multiplex network body ECU) stores this DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
B2762 Intrusion Sensor Signal Circuit Malfunction
After normal/trouble signal is output from theft warning ultrasonic and tilt sensor as result of self-diagnosis, following malfunctions are detected:
1.

ISIF line circuit is open

2.

Reception of signals other than normal/trouble signal


·

Map light assembly

·

Theft warning ultrasonic and tilt sensor

·

Main body ECU (multiplex network body ECU)

·

Harness or connector


Main Body A

WIRING DIAGRAM

B473156E25
2.802,0.417 4.635,0.615 1.833,0.198 10 false MPX-B P NO.1*2 0.594,0.083 2.021,0.385 1.427,0.302 10 false from Auxiliary Battery 1.76,0.875 3.552,1.229 1.792,0.354 10 false Theft Warning Ultrasonic and Tilt Sensor 3.792,1.406 4.167,1.583 0.375,0.177 10 false +B2 3.802,1.99 4.208,2.208 0.406,0.219 10 false IOUT 4.26,2.052 4.667,2.271 0.406,0.219 10 false H8 0.958,1.813 1.365,2.031 0.406,0.219 10 false H8 0.969,1.615 1.375,1.833 0.406,0.219 10 false 19 1.302,1.719 1.708,1.938 0.406,0.219 10 false GND 2.073,3 3.542,3.219 1.469,0.219 10 false Map Light Assembly 4.292,1.323 4.698,1.542 0.406,0.219 10 false 2 4.302,1.875 4.708,2.094 0.406,0.219 10 false 6 5.615,1.99 6.021,2.208 0.406,0.219 10 false ISIF 5.396,1.99 5.802,2.208 0.406,0.219 10 false 14 5.333,2.854 7.01,3.26 1.677,0.406 10 false Main Body ECU (Multiplex Network Body ECU) 5.344,2.708 6.896,3.063 1.552,0.354 10 false D14 6.344,1.573 6.75,1.792 0.406,0.219 10 false +B 4.25,1.51 4.656,1.729 0.406,0.219 10 false H8 2.802,0.25 4.115,0.448 1.313,0.198 10 false MPX-B D NO.1*1 0.188,3.063 1.073,3.26 0.885,0.198 10 false *1: for LHD 0.188,3.365 1.073,3.563 0.885,0.198 10 false *2: for RHD

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

If the main body ECU (multiplex network body ECU) is replaced, refer to the Service Bulletin.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (MAP LIGHT ASSEMBLY - BATTERY AND BODY GROUND)

Pre-procedure1

a.

Disconnect the H8 map light assembly connector.


Procedure1

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(H8)Location & Routing

Click Connector(H8)Body>No. 1 Roof Wire>Map Light Assembly

H8-2 (+B2) - Body ground Ignition switch off 11 to 14 V



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H8)Location & Routing

Click Connector(H8)Body>No. 1 Roof Wire>Map Light Assembly

H8-19 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG


Post-procedure1

a.

None



OK

2.CHECK WAVEFORM (THEFT WARNING ULTRASONIC AND TILT SENSOR) (IOUT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK WAVEFORM (THEFT WARNING ULTRASONIC AND TILT SENSOR) (IOUT)
a.

Using an oscilloscope, check the waveform.

B373999C09
2.083,0.615 2.469,0.833 0.385,0.219 2.927,2.104 3.167,2.104 3.167,2.104 3.854,1.385 true 1.906,2.896 1.698,2.729 false 2.427,2.906 2.229,2.76 false 2.188,0.635 2.5,0.833 0.313,0.198 10 false H8 1.083,0.5 1.396,0.656 0.313,0.156 10 false *a 1.5,2.615 1.813,2.771 0.313,0.156 10 false *b 2.042,2.656 2.354,2.813 0.313,0.156 10 false *c 3.896,2.667 4.208,2.823 0.313,0.156 10 false *d 3.958,3.156 4.271,3.313 0.313,0.156 10 false *e 2.104,3.219 2.417,3.375 0.313,0.156 10 false *f 2.49,3.219 2.792,3.448 0.302,0.229 10 false *g 2.594,3.583 2.906,3.74 0.313,0.156 10 false *h 1.521,4.104 1.833,4.26 0.313,0.156 10 false *i 3.885,4.104 4.094,4.323 0.208,0.219 10 false *j 2.521,2.021 3.031,2.198 0.51,0.177 10 false IOUT 1.115,2.417 1.427,2.615 0.313,0.198 10 false HI 1.146,2.927 1.458,3.125 0.313,0.198 10 false LO
*a Component with harness connected
(Map Light Assembly)
*b IOUT Initial Signal
*c IOUT Initial Response *d Approximately 1.0 second
*e Initial Diagnosis *f Approximately 1.0 to 1.6 seconds
*g Approximately 0.05 seconds *h Approximately 5.5 seconds
*i Disarmed State *j Arming Preparation State


Measurement Condition:
Tester Connection Condition Tool Setting Specified Condition

Click Location & Routing(H8)Location & Routing

Click Connector(H8)Body>No. 1 Roof Wire>Map Light Assembly

H8-6 (IOUT) - Body ground Theft deterrent system is set (system changes from disarmed state to arming preparation state) 2 V/DIV., 100 ms./DIV. The waveform displays properly (HI is 6.5 V or higher and LO is below 1 V).


HINT:
·

If the theft warning ultrasonic and tilt sensor is normal, an initial response is output in response to the HI input from the main body ECU (multiplex network body ECU).

·

If the waveform output remains LO, there may be a problem with the main body ECU (multiplex network body ECU), as there is no input from the main body ECU (multiplex network body ECU).




Result:
Result Proceed to
OK (There is an initial response) A
NG (Waveform output remains LO) B
NG (There is no initial response and the waveform output remains HI) C



A

B

3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] - MAP LIGHT ASSEMBLY)

C

4.INSPECT MAP LIGHT ASSEMBLY
3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] - MAP LIGHT ASSEMBLY)

Pre-procedure1

a.

Disconnect the D14 main body ECU (multiplex network body ECU) connector.


b.

Disconnect the H8 map light assembly connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D14,H8)Location & Routing

Click Connector(D14)Instrument Panel>Instrument Panel Wire>Main Body ECU

Click Connector(H8)Body>No. 1 Roof Wire>Map Light Assembly

D14-14 (ISIF) - H8-6 (IOUT) Always Below 1 Ω
D14-14 (ISIF) or H8-6 (IOUT) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

a.

None



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT MAP LIGHT ASSEMBLY

Pre-procedure1

a.

Remove the map light assembly.

HINT:

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL



Procedure1

a.
B377648N05
1.563,1.625 1.958,1.833 0.396,0.208 1.552,0.281 1.948,0.49 0.396,0.208 1.927,1.063 2.198,1.396 2.198,1.396 2.375,1.396 true 1.688,2.625 2.094,3.188 2.094,3.188 2.229,3.188 true 1.792,1 2.135,0.615 2.135,0.615 2.25,0.604 true 1.531,0.99 1.198,0.615 1.198,0.615 1.052,0.615 true 2.365,2.375 2.667,1.823 2.667,1.823 2.781,1.823 true 1.771,2.396 1.302,1.865 1.302,1.865 1.125,1.865 true 1.719,1.646 1.875,1.844 0.156,0.198 10 false B 1.719,0.292 1.875,0.49 0.156,0.198 10 false A 2.281,3.083 2.688,3.281 0.406,0.198 10 false GND 2.448,1.302 2.854,1.5 0.406,0.198 10 false GND 2.302,0.5 2.708,0.698 0.406,0.198 10 false IOUT 0.698,0.51 1.104,0.708 0.406,0.198 10 false +B2 2.833,1.708 3.24,1.906 0.406,0.198 10 false +B2 0.719,1.75 1.125,1.948 0.406,0.198 10 false IOUT

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-1 (GND) - B-19 (GND) Always Below 1 Ω
A-2 (IOUT) - B-6 (IOUT) Always Below 1 Ω
A-4 (+B2) - B-2 (+B2) Always Below 1 Ω
A-1 (GND) or B-19 (GND) - Other terminals and body ground Always 10 kΩ or higher
A-2 (IOUT) or B-6 (IOUT) - Other terminals and body ground Always 10 kΩ or higher
A-4 (+B2) or B-2 (+B2) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

a.

None



OK

REPLACE THEFT WARNING ULTRASONIC AND TILT SENSOR

NG

REPLACE MAP LIGHT ASSEMBLY