The theft warning ultrasonic and tilt sensor conducts self-diagnosis immediately after power is supplied to the sensor (when the theft deterrent system is set).
If short to ground is detected in the ISIF line, the main body ECU (multiplex network body ECU) stores this DTC.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from | Priority |
|---|---|---|---|---|---|
| B2764 | Short to GND in Intrusion Sensor Signal Circuit | After normal/trouble signal is output from theft warning ultrasonic and tilt sensor as result of self-diagnosis, following malfunctions are detected:
1.
ISIF line circuit is shorted to ground 2.
Reception of signals other than normal/trouble signal |
·
Map light assembly ·
Theft warning ultrasonic and tilt sensor ·
Main body ECU (multiplex network body ECU) ·
Harness or connector |
Main Body | A |
Inspect the fuses for circuits related to this system before performing the following procedure.
If the main body ECU (multiplex network body ECU) is replaced, refer to the Service Bulletin.
Using an oscilloscope, check the waveform.
| *a | Component with harness connected
(Map Light Assembly) |
*b | IOUT Initial Signal |
| *c | IOUT Initial Response | *d | Approximately 1.0 second |
| *e | Initial Diagnosis | *f | Approximately 1.0 to 1.6 seconds |
| *g | Approximately 0.05 seconds | *h | Approximately 5.5 seconds |
| *i | Disarmed State | *j | Arming Preparation State |
| Tester Connection | Condition | Tool Setting | Specified Condition |
|---|---|---|---|
|
Click Location & Routing(H8)Location & Routingewd_type=routing;type=c;code=H8 Click Connector(H8)Body>No. 1 Roof Wire>Map Light Assemblyewd_type=component;type=c;code=H8;pinno=6 |
|||
| H8-6 (IOUT) - Body ground | Theft deterrent system is set (system changes from disarmed state to arming preparation state) | 2 V/DIV., 100 ms./DIV. | The waveform displays properly (HI is 6.5 V or higher and LO is below 1 V). |
If the theft warning ultrasonic and tilt sensor is normal, an initial response is output in response to the HI input from the main body ECU (multiplex network body ECU).
If the waveform output remains LO, there may be a problem with the main body ECU (multiplex network body ECU), as there is no input from the main body ECU (multiplex network body ECU).
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
Pre-procedure1
Disconnect the H8 map light assembly connector.
Procedure1
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition |
|---|---|
|
Click Location & Routing(H8)Location & Routingewd_type=routing;type=c;code=H8 Click Connector(H8)Body>No. 1 Roof Wire>Map Light Assemblyewd_type=component;type=c;code=H8;pinno=6 |
|
| H8-6 (IOUT) - Body ground | Immediately after theft deterrent system set |
| Result | Proceed to |
|---|---|
| IOUT voltage is below 1 V when theft deterrent system is set | A |
| IOUT voltage is 6.5 V or higher when theft deterrent system is set | B |
With connector N9 of the map light assembly disconnected, measure the voltage at IOUT when the theft deterrent system is set.
Post-procedure1
None
A
B
Pre-procedure1
Disconnect the D14 main body ECU (multiplex network body ECU) connector.
Disconnect the H8 map light assembly connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(D14,H8)Location & Routingewd_type=routing;type=c,c;code=D14,H8 Click Connector(D14)Instrument Panel>Instrument Panel Wire>Main Body ECUewd_type=component;type=c;code=D14;pinno=14 Click Connector(H8)Body>No. 1 Roof Wire>Map Light Assemblyewd_type=component;type=c;code=H8;pinno=6 |
||
| D14-14 (ISIF) - H8-6 (IOUT) | Always | Below 1 Ω |
| D14-14 (ISIF) or H8-6 (IOUT) - Other terminals and body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Remove the map light assembly.
Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A-1 (GND) - B-19 (GND) | Always | Below 1 Ω |
| A-2 (IOUT) - B-6 (IOUT) | Always | Below 1 Ω |
| A-4 (+B2) - B-2 (+B2) | Always | Below 1 Ω |
| A-1 (GND) or B-19 (GND) - Other terminals and body ground | Always | 10 kΩ or higher |
| A-2 (IOUT) or B-6 (IOUT) - Other terminals and body ground | Always | 10 kΩ or higher |
| A-4 (+B2) or B-2 (+B2) - Other terminals and body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG