Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM
RM37H0E _58 Vehicle Interior _095303 THEFT DETERRENT / KEYLESS ENTRY _0448454 THEFT DETERRENT SYSTEM J

THEFT DETERRENT / KEYLESS ENTRY  THEFT DETERRENT SYSTEM  Intrusion Sensor Cancel Switch Circuit  


DESCRIPTION

When the intrusion sensor cancel switch on the map light assembly is pressed, the sensor off signal is sent to the main body ECU (multiplex network body ECU) which causes the theft warning ultrasonic and tilt sensor to stop operating.

WIRING DIAGRAM

B501901E02
1.167,1.229 1.479,1.427 0.313,0.198 10 false H8 4.406,1.219 4.719,1.417 0.313,0.198 10 false H8 1.167,1.01 1.479,1.208 0.313,0.198 10 false 19 4.406,1.01 4.719,1.208 0.313,0.198 10 false 22 2.198,1.76 3.563,1.979 1.365,0.219 10 false Map Light Assembly 1.927,1.365 5.083,1.729 3.156,0.365 10 false Intrusion Sensor Cancel Switch 3.875,1.125 4.313,1.344 0.438,0.219 10 false SOFF 1.51,1.125 1.948,1.344 0.438,0.219 10 false GND 5.24,1.938 7.052,2.385 1.813,0.448 10 false Main Body ECU (Multiplex Network Body ECU) 5.271,1.146 5.583,1.344 0.313,0.198 10 false 3 5.458,1.135 5.896,1.354 0.438,0.219 10 false SSW1 5.896,0.813 6.208,1.01 0.313,0.198 10 false +B 5.24,1.781 5.552,1.979 0.313,0.198 10 false D14

CAUTION / NOTICE / HINT

NOTICE:

If the main body ECU (multiplex network body ECU) is replaced, refer to the Service Bulletin.


PROCEDURE

1.READ VALUE USING GTS (Intrusion Sens OFF SW)
a.

According to the display on the GTS, read the Data List.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Intrusion Sens OFF SW Intrusion sensor cancel switch ON or OFF ON: Intrusion sensor cancel switch on
OFF: Intrusion sensor cancel switch off
-
Body Electrical > Main Body > Data List
Tester Display
Intrusion Sens OFF SW
50003 123 203
OK:

The indicator on the GTS switches between ON and OFF in accordance with the intrusion sensor cancel switch status.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK HARNESS AND CONNECTOR (MAP LIGHT ASSEMBLY - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) AND BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (MAP LIGHT ASSEMBLY - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) AND BODY GROUND)
a.

Disconnect the D14 main body ECU (multiplex network body ECU) connector.


b.

Disconnect the H8 map light assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D14,H8)Location & Routing

Click Connector(D14)Instrument Panel>Instrument Panel Wire>Main Body ECU

Click Connector(H8)Body>No. 1 Roof Wire>Map Light Assembly

D14-3 (SSW1) - H8-22 (SOFF) Always Below 1 Ω
H8-19 (GND) - Body ground Always Below 1 Ω
D14-3 (SSW1) or H8-22 (SOFF) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT MAP LIGHT ASSEMBLY (INTRUSION SENSOR CANCEL SWITCH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT MAP LIGHT ASSEMBLY (INTRUSION SENSOR CANCEL SWITCH)
a.

Remove the map light assembly (intrusion sensor cancel switch).

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H8)Location & Routing

Click Connector(H8)Body>No. 1 Roof Wire>Map Light Assembly

H8-22 (SOFF) - H8-19 (GND) Intrusion sensor cancel switch off 10 kΩ or higher
H8-22 (SOFF) - H8-19 (GND) Intrusion sensor cancel switch on Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE MAP LIGHT ASSEMBLY (INTRUSION SENSOR CANCEL SWITCH)