Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM
RM37H0E _58 Vehicle Interior _095303 THEFT DETERRENT / KEYLESS ENTRY _0448454 THEFT DETERRENT SYSTEM J

THEFT DETERRENT / KEYLESS ENTRY  THEFT DETERRENT SYSTEM  Intrusion Sensor Circuit  


DESCRIPTION

If no warnings operate or the system can be set even though the conditions to set the system are not met, the main body ECU (multiplex network body ECU) cannot perform recognition due to a cutoff of the ON signal from the courtesy light switch from the doors, engine hood or back door, or some other problem.

If the automatic alarm operates when it should not operate, it may be due to a false detection by the intrusion sensor (theft warning ultrasonic and tilt sensor) or due to the ON signal being input when there is a short circuit in the courtesy light switch of the doors, engine hood or back door, or some other problem which would cause this to happen.

HINT:

In the following situations, the intrusion sensor (theft warning ultrasonic and tilt sensor) may operate and cause the automatic alarm system to operate even when the sensor is normal.

·

The driver steps away from the vehicle while other people, pets, etc. are in the vehicle.

·

There are things which move easily inside the vehicle, such as things hanging inside the vehicle or clothing hanging from the coat hooks.

·

Any window is open.

·

The vehicle is parked in a place with a lot of vibration or noise such as a parking garage.

·

The vehicle is being washed using a high-pressure spray gun or an automatic car washing machine.

·

The vehicle is continuously being struck or is vibrating due to hail or lightning.

·

The vehicle is continuously being subjected to impacts or is vibrating when snow or ice is being removed from the vehicle.

·

A frost prevention sheet which has an aluminum film is moved by wind, etc.



WIRING DIAGRAM

B473156E26
2.802,0.417 4.635,0.615 1.833,0.198 10 false MPX-B P NO.1*2 0.594,0.083 2.021,0.385 1.427,0.302 10 false from Auxiliary Battery 1.729,0.875 3.573,1.5 1.844,0.625 10 false Intrusion Sensor (Theft Warning Ultrasonic and Tilt Sensor) 3.792,1.406 4.167,1.583 0.375,0.177 10 false +B2 3.802,1.99 4.208,2.208 0.406,0.219 10 false IOUT 4.26,2.052 4.667,2.271 0.406,0.219 10 false H8 0.958,1.813 1.365,2.031 0.406,0.219 10 false H8 0.969,1.615 1.375,1.833 0.406,0.219 10 false 19 1.302,1.719 1.708,1.938 0.406,0.219 10 false GND 2.073,3 3.542,3.219 1.469,0.219 10 false Map Light Assembly 4.292,1.323 4.698,1.542 0.406,0.219 10 false 2 4.302,1.875 4.708,2.094 0.406,0.219 10 false 6 5.615,1.99 6.021,2.208 0.406,0.219 10 false ISIF 5.396,1.99 5.802,2.208 0.406,0.219 10 false 14 5.333,2.854 7.01,3.26 1.677,0.406 10 false Main Body ECU (Multiplex Network Body ECU) 5.344,2.708 6.896,3.063 1.552,0.354 10 false D14 6.344,1.573 6.75,1.792 0.406,0.219 10 false +B 4.25,1.51 4.656,1.729 0.406,0.219 10 false H8 2.802,0.25 4.115,0.448 1.313,0.198 10 false MPX-B D NO.1*1 0.188,3.063 1.073,3.26 0.885,0.198 10 false *1: for LHD 0.188,3.365 1.073,3.563 0.885,0.198 10 false *2: for RHD

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

If the main body ECU (multiplex network body ECU) is replaced, refer to the Service Bulletin.



PROCEDURE

1.READ VALUE USING GTS (Intrusion Sensor, Intrusion Sensor Sound Detect)
a.

Read the Data List according to the display on the GTS.

HINT:

When performing the above inspection, have the electrical key transmitter sub-assembly in the vehicle exterior detection area to perform certification (this prevents the alarm from sounding).


NOTICE:

Make sure that all windows are closed.



b.

Make a metal-on-metal striking sound (such as by shaking keys) near the intrusion sensor (theft warning ultrasonic and tilt sensor) and check the Data List.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Intrusion Sensor Sound Detect Sound detection status of the intrusion sensor (theft warning ultrasonic and tilt sensor)* ON or OFF ON: Sound detected
OFF: Sound not detected
Only displays "ON" on the Data List once. When checking again, disconnect and reconnect the GTS.
Body Electrical > Main Body > Data List
Tester Display
Intrusion Sensor Sound Detect
50003 123 273
NOTICE:

*: Perform the intrusion sensor (theft warning ultrasonic and tilt sensor) operation inspection with the GTS disconnected.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>THEFT DETERRENT SYSTEM>SYSTEM DESCRIPTION



c.

From inside the vehicle, put your hand in front of the intrusion sensor (theft warning ultrasonic and tilt sensor) and move it back and forth a distance of 0.3 m (0.984 ft.) and check the Data List.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Intrusion Sensor Status of the intrusion sensor (theft warning ultrasonic and tilt sensor) detection ON or OFF ON: Moving object detected by sensor
OFF: Both of the conditions below is met
·

No moving object detected by sensor

·

Vehicle tilt not detected by sensor


-
Body Electrical > Main Body > Data List
Tester Display
Intrusion Sensor
50003 123 204
OK:

The GTS display changes correctly in response to the detection condition of the intrusion sensor (theft warning ultrasonic and tilt sensor).



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK WAVEFORM (INTRUSION SENSOR [THEFT WARNING ULTRASONIC AND TILT SENSOR]) (IOUT)
2.CHECK WAVEFORM (INTRUSION SENSOR [THEFT WARNING ULTRASONIC AND TILT SENSOR]) (IOUT)
a.

Using an oscilloscope, check the waveform.

B373999C09
2.083,0.615 2.469,0.833 0.385,0.219 2.927,2.104 3.167,2.104 3.167,2.104 3.854,1.385 true 1.906,2.896 1.698,2.729 false 2.427,2.906 2.229,2.76 false 2.188,0.635 2.5,0.833 0.313,0.198 10 false H8 1.083,0.5 1.396,0.656 0.313,0.156 10 false *a 1.5,2.615 1.813,2.771 0.313,0.156 10 false *b 2.042,2.656 2.354,2.813 0.313,0.156 10 false *c 3.896,2.667 4.208,2.823 0.313,0.156 10 false *d 3.958,3.156 4.271,3.313 0.313,0.156 10 false *e 2.104,3.219 2.417,3.375 0.313,0.156 10 false *f 2.49,3.219 2.792,3.448 0.302,0.229 10 false *g 2.594,3.583 2.906,3.74 0.313,0.156 10 false *h 1.521,4.104 1.833,4.26 0.313,0.156 10 false *i 3.885,4.104 4.094,4.323 0.208,0.219 10 false *j 2.521,2.021 3.031,2.198 0.51,0.177 10 false IOUT 1.115,2.417 1.427,2.615 0.313,0.198 10 false HI 1.146,2.927 1.458,3.125 0.313,0.198 10 false LO
*a Component with harness connected
(Map Light Assembly)
*b IOUT Initial Signal
*c IOUT Initial Response *d Approximately 1.0 second
*e Initial Diagnosis *f Approximately 1.0 to 1.6 seconds
*g Approximately 0.05 seconds *h Approximately 5.5 seconds
*i Disarmed State *j Arming Preparation State


Measurement Condition:
Tester Connection Condition Tool Setting Specified Condition

Click Location & Routing(H8)Location & Routing

Click Connector(H8)Body>No. 1 Roof Wire>Map Light Assembly

H8-6 (IOUT) - Body ground Theft deterrent system is set (system changes from disarmed state to arming preparation state) 2 V/DIV., 100 ms./DIV. The waveform displays properly (HI is 6.5 V or higher and LO is below 1 V).


HINT:
·

If the intrusion sensor (theft warning ultrasonic and tilt sensor) is normal, an initial response is output in response to the HI input from the main body ECU (multiplex network body ECU).

·

If the waveform output remains LO, there may be a problem with the main body ECU (multiplex network body ECU), as there is no input from the main body ECU (multiplex network body ECU).




Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) - MAP LIGHT ASSEMBLY)

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) - MAP LIGHT ASSEMBLY)
a.

Disconnect the D14 main body ECU (multiplex network body ECU) connector.


b.

Disconnect the H8 map light assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D14,H8)Location & Routing

Click Connector(D14)Instrument Panel>Instrument Panel Wire>Main Body ECU

Click Connector(H8)Body>No. 1 Roof Wire>Map Light Assembly

D14-14 (ISIF) - H8-6 (IOUT) Always Below 1 Ω
D14-14 (ISIF) or H8-6 (IOUT) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT MAP LIGHT ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT MAP LIGHT ASSEMBLY
a.

Remove the map light assembly.

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL


b.
B377648N05
1.563,1.625 1.958,1.833 0.396,0.208 1.552,0.281 1.948,0.49 0.396,0.208 1.927,1.063 2.198,1.396 2.198,1.396 2.375,1.396 true 1.688,2.625 2.094,3.188 2.094,3.188 2.229,3.188 true 1.792,1 2.135,0.615 2.135,0.615 2.25,0.604 true 1.531,0.99 1.198,0.615 1.198,0.615 1.052,0.615 true 2.365,2.375 2.667,1.823 2.667,1.823 2.781,1.823 true 1.771,2.396 1.302,1.865 1.302,1.865 1.125,1.865 true 1.719,1.646 1.875,1.844 0.156,0.198 10 false B 1.719,0.292 1.875,0.49 0.156,0.198 10 false A 2.281,3.083 2.688,3.281 0.406,0.198 10 false GND 2.448,1.302 2.854,1.5 0.406,0.198 10 false GND 2.302,0.5 2.708,0.698 0.406,0.198 10 false IOUT 0.698,0.51 1.104,0.708 0.406,0.198 10 false +B2 2.833,1.708 3.24,1.906 0.406,0.198 10 false +B2 0.719,1.75 1.125,1.948 0.406,0.198 10 false IOUT

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-1 (GND) - B-19 (GND) Always Below 1 Ω
A-2 (IOUT) - B-6 (IOUT) Always Below 1 Ω
A-4 (+B2) - B-2 (+B2) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE INTRUSION SENSOR (THEFT WARNING ULTRASONIC AND TILT SENSOR)

NG

REPLACE MAP LIGHT ASSEMBLY