Home › Vehicle Exterior › WINDOW / GLASS › ROOF WINDOW FIX GLASS
RM37H0E _59 Vehicle Exterior _095305 WINDOW / GLASS _0449011 ROOF WINDOW FIX GLASS A

WINDOW / GLASS  ROOF WINDOW FIX GLASS  INSTALLATION  


CAUTION / NOTICE / HINT

COMPONENTS (INSTALLATION)
E444333N04
4.292,1.219 4.292,1.458 false 6.646,0.156 6.917,0.156 false 5.688,1.781 6.177,1.781 false 4.073,3.042 4.073,3.396 false 6.198,0.042 6.75,0.406 0.552,0.365 18 false 2, 4 4.021,3.396 4.344,3.76 0.323,0.365 18 false 5 6.219,1.656 6.396,1.917 0.177,0.26 18 false 1 4.615,1.469 4.938,1.833 0.323,0.365 18 false 3 4.469,1.521 4.792,1.885 0.323,0.365 10 false ●

Procedure Part Name Code
Z101186

Z101188

Z101187

1 ROOF CENTER REINFORCEMENT PROTECTOR 63331C - - -
2 CLEAN NO. 1 ROOF WINDOW GLASS SUB-ASSEMBLY 63201M (Click here) - -
3 INSTALL NO. 1 ROOF WINDOW GLASS SUB-ASSEMBLY 63201M (Click here) - -
4 INSPECT FOR LEAK - (Click here) - -
5 SLIDING ROOF OR REMOVABLE ROOF HOUSING SUB-ASSEMBLY 63203A - - -

● Non-reusable part - -

CAUTION / NOTICE / HINT

NOTICE:
·

Be sure to use the windshield glass adhesive (specialized for high-rigidity specification vehicles) as the adhesive for replacing the windshield glass.

·

Be sure to use the windshield glass adhesive (specialized for high-rigidity specification vehicles) as the adhesive for adjusting the windshield glass.



PROCEDURE

Hide 63331C 1.INSTALL ROOF CENTER REINFORCEMENT PROTECTOR

a.
E444339


Hide 63201M 2.CLEAN NO. 1 ROOF WINDOW GLASS SUB-ASSEMBLY

a.
B585857N01
2.396,0.073 2.677,0.427 0.281,0.354 18 false i

i.

Using non-residue solvent, clean the outer edge of the clean No. 1 window glass sub-assembly.

NOTICE:

Be sure to clean the No. 1 window glass sub-assembly even it is new.




Hide 63201M 3.INSTALL NO. 1 ROOF WINDOW GLASS SUB-ASSEMBLY

a.
B572420C03
0.583,0.198 1.958,0.552 1.375,0.354 18 false i
V100155

Adhesive - -


i.

Follow the procedure below to clean the installation surface of the vehicle body.

1. If the adhesive left on the installation surface of the vehicle body is significantly uneven, smooth it out using a utility knife, etc.

Standard Dimension:
Area Dimension
a 1.0 to 3.0 mm (0.0394 to 0.1181 in.)


NOTICE:
·

Make sure to leave some adhesive.



2. Using non-residue solvent, clean the installation surface of the vehicle body.

3. Apply primer to the exposed sections of the body surface on the vehicle side (where no adhesive remains).

NOTICE:
·

When applying the primer, take care of the panel joints and spot welds.

·

Do not apply to the adhesive.

·

Do not apply too much primer.





b.
E444335C01
0.375,0.042 0.656,0.396 0.281,0.354 18 false i 0.594,2.083 0.75,2.281 0.156,0.198 10 true A 0.979,2.094 1.135,2.292 0.156,0.198 10 true A 2.24,0.844 2.396,1.042 0.156,0.198 10 true B 2.26,0.49 2.417,0.688 0.156,0.198 10 true B 3.094,2.104 3.25,2.302 0.156,0.198 10 true C 3.458,2.104 3.615,2.302 0.156,0.198 10 true C 0.906,0.323 1.219,0.521 0.313,0.198 10 false *a 6.208,0.74 6.667,0.938 0.458,0.198 10 false B-B 4.333,0.74 4.792,0.938 0.458,0.198 10 false A-A 6.063,2.302 6.521,2.5 0.458,0.198 10 false D-D 4.375,2.542 4.531,2.677 0.156,0.135 10 true c 6.292,0.938 6.469,1.073 0.177,0.135 10 true b 4.458,0.917 4.635,1.063 0.177,0.146 10 true a 0.677,2.906 0.833,3.104 0.156,0.198 10 true D 1.052,2.865 1.208,3.063 0.156,0.198 10 true D 4.344,2.333 4.802,2.531 0.458,0.198 10 false C-C 6.115,2.531 6.271,2.667 0.156,0.135 10 true d
*a Backside - -
V100155

Glass Primer - -


i.

Using a brush, apply primer to the entire perimeter of the adhesion area of the No. 1 window glass sub-assembly as shown in the illustration.

NOTICE:

Do not apply too much glass primer.


Standard Dimension:
Area Dimension
a 20.2 mm (0.795 in.) or more
b 18.9 mm (0.744 in.) or more
c 19.8 mm (0.779 in.) or more
d 28.2 mm (1.110 in.) or more




c.
B572423C03
4.781,0.26 4.406,0.385 true 3.177,0.438 3.073,0.292 true 0.563,0.188 0.844,0.542 0.281,0.354 18 false i 2.448,0.49 2.604,0.688 0.156,0.198 10 false a 3.167,1.344 3.323,1.542 0.156,0.198 10 false a 3,0.76 3.156,0.958 0.156,0.198 10 false b 2.615,0.938 2.771,1.135 0.156,0.198 10 false b 4.833,0.188 5.146,0.385 0.313,0.198 10 false *a 3.24,0.385 3.552,0.583 0.313,0.198 10 false *b
*a Sealant Gun *b Nozzle
V100155

Adhesive - -


i.

Cut off the tip of the cartridge nozzle as shown in the illustration, and set the adhesive in the sealant gun.

Standard Dimension:
Area Dimension
a 12 to 15 mm (0.472 to 0.590 in.)
b 8.0 to 11 mm (0.315 to 0.433 in.)




d.
E444336C01
0.354,0.042 0.635,0.396 0.281,0.354 18 false i 0.594,2.104 0.75,2.302 0.156,0.198 10 true A 0.969,2.104 1.125,2.302 0.156,0.198 10 true A 2.25,0.844 2.406,1.042 0.156,0.198 10 true B 2.25,0.479 2.406,0.677 0.156,0.198 10 true B 3.094,2.104 3.25,2.302 0.156,0.198 10 true C 3.458,2.104 3.615,2.302 0.156,0.198 10 true C 0.927,0.417 1.24,0.615 0.313,0.198 10 false *a 4.354,0.26 4.813,0.458 0.458,0.198 10 false A-A 6.188,0.271 6.646,0.469 0.458,0.198 10 false B-B 4.281,2.031 4.74,2.229 0.458,0.198 10 false C-C 4.677,0.542 4.833,0.74 0.156,0.198 10 false a 6.052,0.615 6.208,0.813 0.156,0.198 10 false b 4.167,2.25 4.323,2.448 0.156,0.198 10 false c 6.469,2.448 6.625,2.646 0.156,0.198 10 false d 6.354,2.094 6.51,2.292 0.156,0.198 10 false e 0.688,2.906 0.844,3.104 0.156,0.198 10 true D 1.042,2.885 1.198,3.083 0.156,0.198 10 true D 6.167,1.896 6.625,2.094 0.458,0.198 10 false D-D
*a Backside - -
V100155

Adhesive - -


i.

Apply a bead of adhesive as shown in the illustration.

NOTICE:

After the primer dries (in approximately 3 minutes), apply the adhesive.


Standard Dimension:
Area Dimension
a 13.2 mm (0.519 in.)
b 11.9 mm (0.468 in.)
c 12.8 mm (0.503 in.)
d 13.2 mm (0.519 in.)
e 21.2 mm (0.834 in.)




e.
E444337N01
0.323,0.031 0.604,0.385 0.281,0.354 18 false i

i.

Follow the procedure below to perform No. 1 window glass sub-assembly installation.

1. Using the suction cups, align the matchmarks and install the No. 1 window glass sub-assembly.

2. Using suction cups, align the center of the roof window clip holes on the left and right of the front side of the No. 1 roof window glass sub-assembly with the center of the holes on the body side.

NOTICE:
·

Perform this procedure with 2 or more people, as the part is a heavy component.

·

Be careful not to drop the No. 1 roof window glass sub-assembly.

·

After the body side primer dries (in approximately 3 minutes), install the No. 1 window glass sub-assembly.



3. Gently push the front surface of the No. 1 window glass sub-assembly from outside of vehicle to fully contact with the adhesive.

HINT:

Pushing force: 98 N (10 kgf) or higher


4. Remove any excess adhesive or apply as necessary.

NOTICE:

Apply adhesive up to the edge of the No. 1 window glass sub-assembly.


5. Remove any excess adhesive before it hardens.

6. Using protective tape, hold the outside moulding and glass in place until the adhesive hardens.

NOTICE:

Follow the instructions for each adhesive manufacturer or the corresponding owner's manual for the minimum amount of time necessary for drying and prior to driving the vehicle after applying adhesive.




Hide 4.INSPECT FOR LEAK

a.
E444338N01
0.344,0.042 0.625,0.396 0.281,0.354 18 false i

i.

Follow the procedure below to check for water leak and repair.

1. Remove the protective tape and adhesive tape.

2. After the adhesive has hardened, apply water from outside the vehicle and check for leaks from in the cabin.

3. If water leaks into the cabin, seal any leaks with adhesive after the water has dried.



Hide 63203A 5.INSTALL SLIDING ROOF OR REMOVABLE ROOF HOUSING SUB-ASSEMBLY