Home › Steering › STEERING COLUMN › STEERING WHEEL
RM37H0E _55 Steering _095770 STEERING COLUMN _0449636 STEERING WHEEL A

STEERING COLUMN  STEERING WHEEL  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
C451314N01
6.583,0.25 6.844,0.25 true 6.396,2.052 6.479,2.302 6.479,2.302 6.646,2.302 true 3.094,0.979 3.229,0.573 3.229,0.573 3.396,0.573 true 4.677,2.323 4.76,2.573 4.76,2.573 4.927,2.573 true 6.094,0.104 6.667,0.438 0.573,0.333 18 false 1, 2 6.719,2.146 7,2.5 0.281,0.354 18 false 3 3.74,0.417 4.021,0.771 0.281,0.354 18 false 4 5,2.427 5.281,2.781 0.281,0.354 18 false 5 5.479,1.531 5.792,1.729 0.313,0.198 10 false x 2

Procedure Part Name Code
Z101186

Z101188

Z101187

1 PRECAUTION - (Click here) - -
2 ALIGN FRONT WHEELS FACING STRAIGHT AHEAD - - - -
3 HORN BUTTON ASSEMBLY 45130 - - -
4 STEERING WHEEL ASSEMBLY 45100 (Click here) - -
5 STEERING PAD SWITCH ASSEMBLY 84250A - - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the steering wheel assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced:
Replacement Part or Procedure Necessary Procedures Effects/Inoperative when not Performed Link
Disconnect cable from negative auxiliary battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)


HINT:

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Adaptive high beam system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Air conditioning system After the ignition switch is turned to ON, theservo motor and expansion valve standardposition is recognized. -

·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 1. PRECAUTION

Z101186

Click here(Click here)

Hide 45130 3.REMOVE HORN BUTTON ASSEMBLY

Hide 45100 4.REMOVE STEERING WHEEL ASSEMBLY

a.
C447809C01
6.271,0.375 6.552,0.323 6.552,0.323 6.26,0.281 true 4.104,3.333 4.833,3 4.833,3 5,3 true 4.125,3.583 4.833,3 true 4.583,3.75 4.833,3.021 true 4.125,3.385 4.833,3 true 6.615,0.24 6.823,0.417 0.208,0.177 10 true *a 0.25,0.135 0.5,0.417 0.25,0.281 18 true i 4.177,0.115 4.448,0.406 0.271,0.292 18 true ii 2.635,3.125 2.885,3.406 0.25,0.281 18 true iii 4.323,5.115 4.635,5.313 0.313,0.198 10 false *b 2.823,5.292 3.135,5.49 0.313,0.198 10 false *c 5.083,2.938 5.5,3.219 0.417,0.281 10 false SST
*a Matchmark *b Turn
*c Hold - -


i.

Disconnect each connector.


ii.

Using a socket hexagon wrench (10 mm), remove the bolt, and place matchmarks on the steering wheel assembly and the steering column assembly.


iii.

Using SST, remove the steering wheel assembly.

SST
09950-40011  (09957-04010)
09950-50013  (09951-05010, 09952-05010, 09953-05020, 09954-05070)
09950-60011  (09951-00220)

NOTICE:

Apply a small amount of grease to the threads and tip of SST (09953-05020) before use.




Hide 84250A 5.REMOVE STEERING PAD SWITCH ASSEMBLY