Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Start Function)
RM37H0E _58 Vehicle Interior _095303 THEFT DETERRENT / KEYLESS ENTRY _0449817 ENTRY AND START SYSTEM(for Start Function) C

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function)  B2274  ACC Monitor Malfunction  


DESCRIPTION

This DTC is stored when a malfunction in the ACC output circuit is detected. The ACC output circuit is the circuit between terminal ACCD of the certification ECU (smart key ECU assembly) and the ACC relay.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority Note
B2274 ACC Monitor Malfunction The ACC relay circuit of the certification ECU (smart key ECU assembly) is malfunctioning. (1-trip detection logic*)
HINT:

When the voltage at terminal ACCD is not at the standard, the system is determined to be malfunctioning.


·

LUG-ACC relay

·

Driver side junction block assembly (ACC D relay)

·

Passenger side junction block assembly (ACC P relay)

·

Certification ECU (smart key ECU assembly)

·

Harness or connector


Power Source Control A
DTC Output Confirmation Operation:

Wait 10 seconds after turning the ignition switch to ACC or to ON, and then wait another 10 seconds after turning the ignition switch off.



*: Only detected while a malfunction is present.


Vehicle Condition and Fail-safe Function when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Function when Malfunction Detected
·

If there is a malfunction due to the ACC relay being stuck on, the ACC relay does not turn off even though the ignition switch is off.

·

If there is a malfunction due to the ACC relay being stuck off, the ACC relay does not turn on even though the ignition switch is ACC.


HINT:

The ignition switch can be turned to ON and the hybrid control system can be started.


-

Related Data List and Active Test Items
DTC No. Data List and Active Test
B2274
Power Source Control
·

ACC Relay Monitor



WIRING DIAGRAM

for LHD:
B598253E01
5.531,1.354 5.99,1.552 0.458,0.198 10 false D86 5.542,1.479 7.094,1.854 1.552,0.375 10 false Certification ECU (Smart Key ECU Assembly) 6.208,0.219 6.667,0.417 0.458,0.198 10 false +B 6.656,0.646 6.969,0.969 0.313,0.323 10 false IC 5.906,0.594 6.427,0.906 0.521,0.313 10 false ACCD 5.646,0.583 6.167,0.896 0.521,0.313 10 false 16 5.177,4.083 6.615,4.5 1.438,0.417 10 false from Auxiliary Battery 2.781,1.854 3.302,2.167 0.521,0.313 10 false ACC D 3.469,1.313 3.99,1.625 0.521,0.313 10 false ACC D 2.052,3.229 4.5,3.479 2.448,0.25 10 false Driver Side Junction Block Assembly 1.854,5.323 4.563,5.604 2.708,0.281 10 false Passenger Side Junction Block Assembly 3.344,4.771 3.99,4.99 0.646,0.219 10 false ACC P 2.51,4.271 3.563,4.5 1.052,0.229 10 false ACC P NO.1 1.74,4.094 2.125,4.281 0.385,0.188 10 false 5D 1.75,4.917 2.135,5.104 0.385,0.188 10 false 5D 1.729,4.479 2.115,4.667 0.385,0.188 10 false 5A 4.354,4.094 4.74,4.281 0.385,0.188 10 false 5K 4.396,3.885 4.781,4.073 0.385,0.188 10 false 1 1.74,4.729 2.125,4.917 0.385,0.188 10 false 26 1.76,3.927 2.146,4.115 0.385,0.188 10 false 15 1.771,4.292 2.156,4.479 0.385,0.188 10 false 9 1.729,0.677 2.115,0.865 0.385,0.188 10 false 4A 4.365,1.135 4.75,1.323 0.385,0.188 10 false 4D 4.365,0.677 4.75,0.865 0.385,0.188 10 false 4D 4.365,2.74 4.75,2.927 0.385,0.188 10 false 4H 1.719,1.125 2.104,1.313 0.385,0.188 10 false 4K 4.365,1.542 4.75,1.729 0.385,0.188 10 false 4D 4.385,2.51 4.771,2.698 0.385,0.188 10 false 32 4.396,1.354 4.781,1.542 0.385,0.188 10 false 6 4.365,0.5 4.75,0.688 0.385,0.188 10 false 17 1.75,0.49 2.135,0.677 0.385,0.188 10 false 18 1.771,0.938 2.156,1.125 0.385,0.188 10 false 1 6.813,2.646 7.125,2.833 0.313,0.188 10 false 1 6.156,2.635 6.542,2.823 0.385,0.188 10 false 2 6.167,2.25 6.552,2.438 0.385,0.188 10 false 5 6.802,2.25 7.042,2.458 0.24,0.208 10 false 3 6.208,3.031 6.917,3.396 0.708,0.365 10 false LUG-ACC 4.344,0.927 5.052,1.292 0.708,0.365 10 false 22 0.604,1.125 1.208,1.667 0.604,0.542 10 false from Auxiliary Battery 4.531,2.281 6.229,2.698 1.698,0.417 10 false from Auxiliary Battery

for RHD:
C375423E31
4.979,2.438 7.156,2.854 2.177,0.417 10 false Certification ECU (Smart Key ECU Assembly) 4.958,2.26 5.438,2.49 0.479,0.229 10 false D86 6.458,0.948 6.698,1.177 0.24,0.229 10 false IC 6.021,0.542 6.26,0.771 0.24,0.229 10 false +B 5.698,1.115 6.219,1.479 0.521,0.365 10 false ACCD 5.458,0.917 5.698,1.146 0.24,0.229 10 false 16 4.135,0.99 4.615,1.219 0.479,0.229 10 false 4D 4.135,0.823 4.615,1.052 0.479,0.229 10 false 18 1.49,0.99 1.969,1.219 0.479,0.229 10 false 4A 1.5,0.813 1.979,1.042 0.479,0.229 10 false 21 4.135,1.844 4.615,2.073 0.479,0.229 10 false 4D 4.167,1.667 4.646,1.896 0.479,0.229 10 false 7 1.49,1.438 1.969,1.667 0.479,0.229 10 false 4K 1.51,1.271 1.99,1.5 0.479,0.229 10 false 1 2.656,2.125 3.177,2.49 0.521,0.365 10 false ACC D 3.292,1.635 3.813,2 0.521,0.365 10 false ACC D 4.135,1.448 4.615,1.677 0.479,0.229 10 false 4D 4.146,1.271 4.625,1.5 0.479,0.229 10 false 22 1.802,2.406 4.219,2.76 2.417,0.354 10 false Driver Side Junction Block Assembly 1.74,4.417 4.667,4.771 2.927,0.354 10 false Passenger Side Junction Block Assembly 1.51,3.781 1.99,4.01 0.479,0.229 10 false 5D 1.542,3.615 2.021,3.844 0.479,0.229 10 false 32 4.125,3.76 4.604,3.99 0.479,0.229 10 false 5H 4.146,3.594 4.625,3.823 0.479,0.229 10 false 21 4.135,2.948 4.615,3.177 0.479,0.229 10 false 5K 4.167,2.771 4.646,3 0.479,0.229 10 false 1 3.219,3.635 3.74,4 0.521,0.365 10 false ACC P 2.292,3.115 3.198,3.531 0.906,0.417 10 false ACC P NO.1 1.5,3.333 1.979,3.563 0.479,0.229 10 false 5A 1.573,3.177 2.052,3.406 0.479,0.229 10 false 9 1.5,2.958 1.979,3.188 0.479,0.229 10 false 5D 1.521,2.781 2,3.01 0.479,0.229 10 false 28 5.01,4.073 5.719,4.438 0.708,0.365 10 false LUG-ACC 5.677,3.688 5.969,3.896 0.292,0.208 10 false 1 5.01,3.698 5.302,3.906 0.292,0.208 10 false 2 5.01,3.313 5.302,3.521 0.292,0.208 10 false 3 5.656,3.313 5.948,3.521 0.292,0.208 10 false 5 5.927,3.354 6.854,3.729 0.927,0.375 10 false from Auxiliary Battery 0.417,1.438 0.979,2.094 0.563,0.656 10 false from Auxiliary Battery 4.74,2.948 6.198,3.146 1.458,0.198 10 false from Auxiliary Battery

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the ignition switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start. While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

The entry and start system (for Start Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Inspect the fuses of circuits related to this system before performing the following procedure.

·

Before replacing the certification ECU (smart key ECU assembly), refer to the Service Bulletin.

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".



PROCEDURE

1.CHECK VEHICLE CONDITION
a.

Check vehicle condition.


Result:
Proceed to
for LHD
for RHD



for LHD

2.CHECK HARNESS AND CONNECTOR (DRIVER SIDE JUNCTION BLOCK ASSEMBLY - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY), POWER SUPPLY AND BODY GROUND)

for RHD

9.CHECK HARNESS AND CONNECTOR (DRIVER SIDE JUNCTION BLOCK ASSEMBLY - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY), POWER SUPPLY AND BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (DRIVER SIDE JUNCTION BLOCK ASSEMBLY - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY), POWER SUPPLY AND BODY GROUND)

Pre-procedure1

a.

Disconnect the 4D and 4K driver side junction block assembly connectors.


b.

Disconnect the D86 certification ECU (smart key ECU assembly) connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D86)Location & Routing

Click Connector(D86)Instrument Panel>Instrument Panel Wire>Certification ECU

D86-16 (ACCD) - 4D-17 Always Below 1 Ω
4D-6 - Body ground Always Below 1 Ω
D86-16 (ACCD) or 4D-17 - Other terminals and body ground Always 10 kΩ or higher



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
4K-1 - Body ground Ignition switch off 11 to 14 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None.



OK

3.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

Pre-procedure1

a.
B498244C65
1.604,0.115 1.969,0.354 0.365,0.24 1.125,1.99 1.292,1.99 1.292,1.99 1.292,0.969 true 1.667,0.135 2.01,0.333 0.344,0.198 10 false D86 0.719,1.917 1.313,2.115 0.594,0.198 10 false ACCD 0.073,0.042 0.385,0.198 0.313,0.156 10 false *a
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))


Reconnect the certification ECU (smart key ECU assembly) connector.


Procedure1

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(D86)Location & Routing

Click Connector(D86)Instrument Panel>Instrument Panel Wire>Certification ECU

D86-16 (ACCD) - Body ground Ignition switch off 1 V or less
D86-16 (ACCD) - Body ground Ignition switch ACC 8.5 V or higher



Result:
Proceed to
OK
NG


Post-procedure1

a.

None.



OK

4.CHECK HARNESS AND CONNECTOR (LUG-ACC RELAY - DRIVER SIDE JUNCTION BLOCK ASSEMBLY, POWER SUPPLY AND BODY GROUND)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

4.CHECK HARNESS AND CONNECTOR (LUG-ACC RELAY - DRIVER SIDE JUNCTION BLOCK ASSEMBLY, POWER SUPPLY AND BODY GROUND)

Pre-procedure1

a.

Disconnect the 4H driver side junction block assembly connector.


b.

Remove the LUG-ACC relay.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4H-32 - LUG-ACC relay installation terminal 2 Always Below 1 Ω
LUG-ACC relay installation terminal 1 - Body ground Always Below 1 Ω
4H-32 or LUG-ACC relay installation terminal 2 - Other terminals and body ground Always 10 kΩ or higher



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
LUG-ACC relay installation terminal 3 - Body ground Ignition switch off 11 to 14 V



Result:
Proceed to
OK
NG


Post-procedure1

a.

None.



OK

5.CHECK HARNESS AND CONNECTOR (PASSENGER SIDE JUNCTION BLOCK ASSEMBLY - DRIVER SIDE JUNCTION BLOCK ASSEMBLY, POWER SUPPLY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (PASSENGER SIDE JUNCTION BLOCK ASSEMBLY - DRIVER SIDE JUNCTION BLOCK ASSEMBLY, POWER SUPPLY AND BODY GROUND)

Pre-procedure1

a.

Disconnect the 5D, 5A and 5K passenger side junction block assembly connectors.


b.

Disconnect the 4A driver side junction block assembly connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4A-18 - 5D-26 Always Below 1 Ω
5A-9 - Body ground Always Below 1 Ω
4A-18 or 5D-26 - Other terminals and body ground Always 10 kΩ or higher



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
5K-1 - Body ground Ignition switch off 11 to 14 V



Result:
Proceed to
OK
NG


Post-procedure1

a.

None.



OK

6.CHECK DRIVER SIDE JUNCTION BLOCK ASSEMBLY (ACC D RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK DRIVER SIDE JUNCTION BLOCK ASSEMBLY (ACC D RELAY)

Pre-procedure1

a.

Remove the driver side junction block assembly.

HINT:

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL



b.

Reconnect the all driver side junction block assembly connectors.


Procedure1

a.

Measure the voltage according to the value(s) in the table below.

C377231C33
2.292,1.583 2.656,1.781 0.365,0.198 2.938,3.313 3.302,3.51 0.365,0.198 4.375,3.302 4.74,3.5 0.365,0.198 2.396,1.594 2.708,1.792 0.313,0.198 10 false 4H 0.24,0.333 0.552,0.531 0.313,0.198 10 false *a 3.021,3.323 3.333,3.521 0.313,0.198 10 false 4A 4.49,3.313 4.802,3.51 0.313,0.198 10 false 4D
*a Component with harness connected
(Driver Side Junction Block Assembly)
- -


Standard Voltage:
Tester Connection Switch Condition Specified Condition
4D-22 - Body ground Ignition switch ACC 11 to 14 V
4A-18 - Body ground Ignition switch ACC 8.5 to 14 V
4H-32 - Body ground Ignition switch ACC 8.5 to 14 V



Result:
Proceed to
OK
NG


Post-procedure1

a.

None.



OK

7.CHECK PASSENGER SIDE JUNCTION BLOCK ASSEMBLY (ACC P RELAY)

NG

REPLACE DRIVER SIDE JUNCTION BLOCK ASSEMBLY

7.CHECK PASSENGER SIDE JUNCTION BLOCK ASSEMBLY (ACC P RELAY)

Pre-procedure1

a.

Remove the passenger side junction block assembly.

HINT:

Click herePower Source / Network>NETWORKING>NETWORK GATEWAY ECU>REMOVAL



b.

Reconnect the all passenger side junction block assembly connectors.


Procedure1

a.

Measure the voltage according to the value(s) in the table below.

C376270C12
4.646,2.385 5.031,2.594 0.385,0.208 0.24,0.333 0.552,0.531 0.313,0.198 10 false *a 4.76,2.396 5.073,2.594 0.313,0.198 10 false 5D
*a Component with harness connected
(Passenger Side Junction Block Assembly)
- -


Standard Voltage:
Tester Connection Switch Condition Specified Condition
5D-15 - Body ground Ignition switch ACC 11 to 14 V



Result:
Proceed to
OK
NG


Post-procedure1

a.

None.



OK

8.INSPECT LUG-ACC RELAY

NG

REPLACE PASSENGER SIDE JUNCTION BLOCK ASSEMBLY

8.INSPECT LUG-ACC RELAY
a.
C279145C15
2.031,0.625 1.677,0.385 false 2.604,0.677 2.917,0.469 false 2.385,1.135 2.875,1.135 false 2.448,1.635 2.906,1.635 false 0.24,0.667 0.396,0.865 0.156,0.198 10 false 3 1.188,0.677 1.344,0.875 0.156,0.198 10 false 5 0.24,1.198 0.396,1.396 0.156,0.198 10 false 1 1.188,1.219 1.375,1.417 0.188,0.198 10 false 2 2.99,0.333 3.146,0.531 0.156,0.198 10 false 1 1.552,0.25 1.708,0.448 0.156,0.198 10 false 2 2.979,1.073 3.135,1.271 0.156,0.198 10 false 5 3,1.563 3.156,1.76 0.156,0.198 10 false 3 0.26,0.167 0.458,0.375 0.198,0.208 10 false *1
*1 LUG-ACC Relay


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Auxiliary battery voltage applied between terminals 1 and 2 Below 1 Ω
Auxiliary battery voltage not applied between terminals 1 and 2 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPLACE LUG-ACC RELAY

9.CHECK HARNESS AND CONNECTOR (DRIVER SIDE JUNCTION BLOCK ASSEMBLY - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY), POWER SUPPLY AND BODY GROUND)

Pre-procedure1

a.

Disconnect the 4D and 4K driver side junction block assembly connectors.


b.

Disconnect the D86 certification ECU (smart key ECU assembly) connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D86)Location & Routing

Click Connector(D86)Instrument Panel>Instrument Panel Wire>Certification ECU

D86-16 (ACCD) - 4D-18 Always Below 1 Ω
4D-7 - Body ground Always Below 1 Ω
D86-16 (ACCD) or 4D-18 - Other terminals and body ground Always 10 kΩ or higher



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
4K-1 - Body ground Ignition switch off 11 to 14 V



Result:
Proceed to
OK
NG


Post-procedure1

a.

None.



OK

10.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

Pre-procedure1

a.
B498244C65
1.604,0.115 1.969,0.354 0.365,0.24 1.125,1.99 1.292,1.99 1.292,1.99 1.292,0.969 true 1.667,0.135 2.01,0.333 0.344,0.198 10 false D86 0.719,1.917 1.313,2.115 0.594,0.198 10 false ACCD 0.073,0.042 0.385,0.198 0.313,0.156 10 false *a
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))


Reconnect the certification ECU (smart key ECU assembly) connector.


Procedure1

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(D86)Location & Routing

Click Connector(D86)Instrument Panel>Instrument Panel Wire>Certification ECU

D86-16 (ACCD) - Body ground Ignition switch off 1 V or less
D86-16 (ACCD) - Body ground Ignition switch ACC 8.5 V or higher



Result:
Proceed to
OK
NG


Post-procedure1

a.

None.



OK

11.CHECK HARNESS AND CONNECTOR (PASSENGER SIDE JUNCTION BLOCK ASSEMBLY - DRIVER SIDE JUNCTION BLOCK ASSEMBLY, POWER SUPPLY AND BODY GROUND)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

11.CHECK HARNESS AND CONNECTOR (PASSENGER SIDE JUNCTION BLOCK ASSEMBLY - DRIVER SIDE JUNCTION BLOCK ASSEMBLY, POWER SUPPLY AND BODY GROUND)

Pre-procedure1

a.

Disconnect the 5D, 5A and 5K passenger side junction block assembly connectors.


b.

Disconnect the 4A driver side junction block assembly connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4A-21 - 5D-32 Always Below 1 Ω
5A-9 - Body ground Always Below 1 Ω
4A-21 or 5D-32 - Other terminals and body ground Always 10 kΩ or higher



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
5K-1 - Body ground Ignition switch off 11 to 14 V



Result:
Proceed to
OK
NG


Post-procedure1

a.

Reconnect the 5D driver side junction block assembly connector.



OK

12.CHECK HARNESS AND CONNECTOR (LUG-ACC RELAY - PASSENGER SIDE JUNCTION BLOCK ASSEMBLY, POWER SUPPLY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.CHECK HARNESS AND CONNECTOR (LUG-ACC RELAY - PASSENGER SIDE JUNCTION BLOCK ASSEMBLY, POWER SUPPLY AND BODY GROUND)

Pre-procedure1

a.

Disconnect the 5H passenger side junction block assembly connector.


b.

Remove the LUG-ACC relay.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
5H-21 - LUG-ACC relay installation terminal 2 Always Below 1 Ω
LUG-ACC relay installation terminal 1 - Body ground Always Below 1 Ω
5H-21 or LUG-ACC relay installation terminal 2 - Other terminals and body ground Always 10 kΩ or higher



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
LUG-ACC relay installation terminal 3 - Body ground Ignition switch off 11 to 14 V



Result:
Proceed to
OK
NG


Post-procedure1

a.

None.



OK

13.CHECK DRIVER SIDE JUNCTION BLOCK ASSEMBLY (ACC D RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.CHECK DRIVER SIDE JUNCTION BLOCK ASSEMBLY (ACC D RELAY)

Pre-procedure1

a.

Remove the driver side junction block assembly.

HINT:

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL



b.

Reconnect the all driver side junction block assembly connectors.


Procedure1

a.

Measure the voltage according to the value(s) in the table below.

C376269C20
2.802,2.333 3.24,2.573 0.438,0.24 4.583,2.385 5.021,2.625 0.438,0.24 0.177,0.323 0.49,0.521 0.313,0.198 10 false *a 2.948,2.365 3.26,2.563 0.313,0.198 10 false 4A 4.708,2.417 5.021,2.615 0.313,0.198 10 false 4D
*a Component with harness connected
(Driver Side Junction Block Assembly)
- -


Standard Voltage:
Tester Connection Switch Condition Specified Condition
4D-22 - Body ground Ignition switch ACC 11 to 14 V
4A-21 - Body ground Ignition switch ACC 8.5 to 14 V



Result:
Proceed to
OK
NG


Post-procedure1

a.

None.



OK

14.CHECK PASSENGER SIDE JUNCTION BLOCK ASSEMBLY (ACC P RELAY)

NG

REPLACE DRIVER SIDE JUNCTION BLOCK ASSEMBLY

14.CHECK PASSENGER SIDE JUNCTION BLOCK ASSEMBLY (ACC P RELAY)

Pre-procedure1

a.

Remove the passenger side junction block assembly.

HINT:

Click herePower Source / Network>NETWORKING>NETWORK GATEWAY ECU>REMOVAL



b.

Reconnect the all passenger side junction block assembly connectors.


Procedure1

a.

Measure the voltage according to the value(s) in the table below.

C376683C30
4.573,1.781 4.948,1.979 0.375,0.198 2.354,3.531 2.729,3.729 0.375,0.198 2.469,3.542 2.781,3.74 0.313,0.198 10 false 5H 4.688,1.792 5,1.99 0.313,0.198 10 false 5D 0.271,0.219 0.583,0.417 0.313,0.198 10 false *a
*a Component with harness connected
(Passenger Side Junction Block Assembly)
- -


Standard Voltage:
Tester Connection Switch Condition Specified Condition
5D-28 - Body ground Ignition switch ACC 11 to 14 V
5H-21 - Body ground Ignition switch ACC 8.5 to 14 V



Result:
Proceed to
OK
NG


Post-procedure1

a.

None.



OK

15.INSPECT LUG-ACC RELAY

NG

REPLACE PASSENGER SIDE JUNCTION BLOCK ASSEMBLY

15.INSPECT LUG-ACC RELAY
a.
C279145C15
2.031,0.625 1.677,0.385 false 2.604,0.677 2.917,0.469 false 2.385,1.135 2.875,1.135 false 2.448,1.635 2.906,1.635 false 0.24,0.667 0.396,0.865 0.156,0.198 10 false 3 1.188,0.677 1.344,0.875 0.156,0.198 10 false 5 0.24,1.198 0.396,1.396 0.156,0.198 10 false 1 1.188,1.219 1.375,1.417 0.188,0.198 10 false 2 2.99,0.333 3.146,0.531 0.156,0.198 10 false 1 1.552,0.25 1.708,0.448 0.156,0.198 10 false 2 2.979,1.073 3.135,1.271 0.156,0.198 10 false 5 3,1.563 3.156,1.76 0.156,0.198 10 false 3 0.26,0.167 0.458,0.375 0.198,0.208 10 false *1
*1 LUG-ACC Relay


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Auxiliary battery voltage applied between terminals 1 and 2 Below 1 Ω
Auxiliary battery voltage not applied between terminals 1 and 2 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPLACE LUG-ACC RELAY