If additional registration is not possible, a malfunction of the electrical key transmitter sub-assembly, certification ECU (smart key ECU assembly), power switch, No. 1 indoor electrical key antenna assembly (front floor), steering lock ECU (steering lock actuator or upper bracket assembly) or door control receiver is suspected.
If registration of an electrical key transmitter sub-assembly cannot be performed, refer to the Service Bulletin.
When using the GTS with the ignition switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start. While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.
The entry and start system (for Start Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Start Function) after confirming that the communication systems are functioning properly.
Before replacing the certification ECU (smart key ECU assembly), steering lock ECU (steering lock actuator or upper bracket assembly) or electrical key transmitter sub-assembly, refer to the Service Bulletin.
After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".
When additional registration is not possible, operation history may be stored in the certification ECU (smart key ECU assembly).
Check for DTCs.
If a malfunction occurs, do not remove/install the vehicle auxiliary battery before checking for DTCs.
DTCs are not output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Unmatched Vehicle-ID | Key No. (incorrect or correct) | Yes or No | Yes: Communication malfunction
No: Communication normal |
The vehicle ID registered in the vehicle and the vehicle ID registered in the electrical key transmitter sub-assembly are different (if a key from another vehicle is brought into the vehicle exterior detection area while the doors are locked, "Yes" is displayed for "Unmatched Vehicle-ID" in the Data List).
Other potential causes: ·
An electrical key transmitter sub-assembly from a different vehicle is being used. ·
A communication error due to wave interference. ·
The electrical key transmitter sub-assembly or certification ECU (smart key ECU assembly) is malfunctioning. |
| Tester Display |
|---|
| Unmatched Vehicle-ID |
| Result | Proceed to |
|---|---|
| "No" is displayed | A |
| "Yes" is displayed | B |
A
B
| *1 | Power Switch |
| *2 | Electrical Key Transmitter Sub-assembly |
Remove the transmitter battery from the electrical key transmitter sub-assembly.
With the brake pedal depressed, hold the electrical key transmitter sub-assembly near the power switch and check if the power source mode changes.
The power source mode changes.
If the power source mode changes, the cabin verification is malfunctioning.
| Result | Proceed to |
|---|---|
| The power source mode changes | A |
| The power source mode does not change | B |
A
B
Check that the steering unlocks when all of the following conditions are met.
The electrical key transmitter sub-assembly is inside the vehicle.
Ignition switch is ACC or ON.
Check that the communication between the steering lock ECU (steering lock actuator or upper bracket assembly) and certification ECU (smart key ECU assembly) is normal.
The steering unlocks.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Using another unregistered electrical key transmitter sub-assembly, perform the additional registration procedure.
Refer to Service Bulletin.
Additional registration can be completed.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Temporarily replace the certification ECU (smart key ECU assembly) with a new one and register the electrical key transmitter sub-assemblies.
Refer to Service Bulletin.
All of the electrical key transmitter sub-assemblies could be registered to the new certification ECU (smart key ECY assembly) successfully.
| Proceed to |
|---|
| OK |
| NG |
OK
NG