Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Start Function)
RM37H0E _58 Vehicle Interior _095303 THEFT DETERRENT / KEYLESS ENTRY _0449817 ENTRY AND START SYSTEM(for Start Function) J

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function)  Power Source Mode does not Change to ON (IG and ACC)  


DESCRIPTION

When the ignition switch cannot be turned to ACC or to ON, there may be a malfunction in interior certification, or the ACC relay or IG relay system. If interior certification does not succeed, the certification ECU (smart key ECU assembly) may be malfunctioning, or communication may not be possible between the No. 1 indoor electrical key antenna assembly (front floor) or No. 2 indoor electrical key antenna assembly (rear floor), the electrical key transmitter sub-assembly, and the door control receiver.

When the electrical key transmitter sub-assembly is brought into the cabin, the key ID code sent from the electrical key transmitter sub-assembly and the key ID code stored in the certification ECU (smart key ECU assembly) are certified. If these codes do not match and certification fails, the ignition switch cannot be turned to ACC or to ON.

When the door is unlocked and the electrical key transmitter sub-assembly is brought into the cabin, the certification ECU (smart key ECU assembly) activates the indoor electrical key antenna and forms a detection area. When the electrical key transmitter sub-assembly is recognized inside the detection area, it returns the key ID code. This is received by the door control receiver, which then sends it to the certification ECU (smart key ECU assembly).

Related Data List and Active Test Items
Problem Symptom Data List and Active Test
Power source mode does not change to on (IG) or on (ACC)
Power Source Control
·

Start Switch1

·

Start Switch2

·

IG Relay Monitor (Inside)

·

ACC Relay Monitor

·

IG Relay Monitor (Outside)

·

Latch Circuit

·

Power Supply Condition



WIRING DIAGRAM

for LHD:
B501961E10
0.552,0.833 1.948,1.052 1.396,0.219 10 false from Auxiliary Battery 1.094,4.469 1.958,4.844 0.865,0.375 10 false from Auxiliary Battery 4.688,0.177 6.104,0.385 1.417,0.208 10 false from Auxiliary Battery 0.927,0.563 2.76,0.76 1.833,0.198 10 false AM2 0.24,3.906 2.073,4.104 1.833,0.198 10 false D98 0.26,4.052 2.094,4.25 1.833,0.198 10 false Power Switch 0.917,3.49 2.75,3.688 1.833,0.198 10 false AGND 1.052,2.844 2.885,3.042 1.833,0.198 10 false SS2 1.052,2.208 2.885,2.406 1.833,0.198 10 false SS1 2.167,2.188 4,2.385 1.833,0.198 10 false SSW1 2.156,2.823 3.99,3.021 1.833,0.198 10 false SSW2 3.042,2.583 4.875,2.781 1.833,0.198 10 false IC 2.177,3.458 4.01,3.656 1.833,0.198 10 false AGND 2.427,0.844 4.26,1.042 1.833,0.198 10 false IC 2.156,0.417 3.99,0.615 1.833,0.198 10 false +B 2.156,1.406 3.99,1.604 1.833,0.198 10 false E 2.833,0.5 4.667,0.698 1.833,0.198 10 false +B 2.667,1.698 4.5,1.896 1.833,0.198 10 false +B 2.906,0.906 4.74,1.104 1.833,0.198 10 false ACCD 0.292,5.969 2.125,6.167 1.833,0.198 10 false A3 0.094,6.104 1.927,6.302 1.833,0.198 10 false Stop Light Switch Assembly 1.958,8.302 3.51,8.688 1.552,0.385 10 false Certification ECU (Smart Key ECU Assembly) 2.448,6.698 4.281,6.896 1.833,0.198 10 false IC 2.823,6.344 4.656,6.542 1.833,0.198 10 false +B 4.354,1.76 6.188,1.958 1.833,0.198 10 false ACC D 5.156,2.167 6.99,2.365 1.833,0.198 10 false ACC D 3.052,5.406 4.885,5.604 1.833,0.198 10 false IC 2.917,6.76 4.75,6.958 1.833,0.198 10 false IG1D 1.198,5.26 3.031,5.458 1.833,0.198 10 false L 0.438,5.333 2.271,5.531 1.833,0.198 10 false B 0.417,5.635 2.25,5.833 1.833,0.198 10 false GND 2.146,5.229 3.979,5.427 1.833,0.198 10 false STP1 4.167,8.365 6.865,8.573 2.698,0.208 10 false Driver Side Junction Block Assembly 3.375,0.969 5.208,1.167 1.833,0.198 10 false D86 1.792,0.438 3.625,0.635 1.833,0.198 10 false D86 1.792,1.385 3.625,1.583 1.833,0.198 10 false D86 1.792,2.292 3.625,2.49 1.833,0.198 10 false D86 1.781,2.927 3.615,3.125 1.833,0.198 10 false D86 1.771,3.552 3.604,3.75 1.833,0.198 10 false D86 3.365,6.833 5.198,7.031 1.833,0.198 10 false D86 1.802,5.333 3.635,5.531 1.833,0.198 10 false G37 3.948,0.969 5.781,1.167 1.833,0.198 10 false 4D 3.948,5.854 5.781,6.052 1.833,0.198 10 false 4D 3.958,6.375 5.792,6.573 1.833,0.198 10 false 4D 3.958,6.833 5.792,7.031 1.833,0.198 10 false 4D 6.281,0.979 7.156,1.188 0.875,0.208 10 false 4A 6.281,6.833 7.156,7.042 0.875,0.208 10 false 4A 3.948,4.375 4.823,4.583 0.875,0.208 10 false 4D 3.938,3.01 4.813,3.219 0.875,0.208 10 false 4A 3.969,1.635 4.844,1.844 0.875,0.208 10 false 4D 5.021,4.938 6.854,5.135 1.833,0.198 10 false IG1 D NO.1 4.99,3.531 5.771,3.729 0.781,0.198 10 false IG1 D NO.2 5.167,6.604 7,6.802 1.833,0.198 10 false IG2 D 6.281,1.885 7.156,2.094 0.875,0.208 10 false 4A 6.271,7.719 7.146,7.927 0.875,0.208 10 false 4H 6.281,7.292 7.156,7.5 0.875,0.208 10 false 4F 6.281,8.104 7.156,8.313 0.875,0.208 10 false 4F 6.281,3 7.156,3.208 0.875,0.208 10 false 4K 6.281,5.865 7.156,6.073 0.875,0.208 10 false 4L 4.365,3.115 4.75,3.667 0.385,0.552 10 false IG1 D NO.4 4.385,4.51 4.771,5.063 0.385,0.552 10 false IG1 D NO.3 4.427,6.031 4.813,6.583 0.385,0.552 10 false IG2 D NO.2 1.813,1.198 3.646,1.396 1.833,0.198 10 false 18 1.865,0.25 3.698,0.448 1.833,0.198 10 false 4 1.823,2.125 3.656,2.323 1.833,0.198 10 false 23 1.833,2.74 3.667,2.938 1.833,0.198 10 false 21 1.833,3.365 3.667,3.563 1.833,0.198 10 false 11 1.385,3.458 3.219,3.656 1.833,0.198 10 false 6 1.385,2.823 3.219,3.021 1.833,0.198 10 false 1 1.396,2.208 3.229,2.406 1.833,0.198 10 false 5 3.396,0.792 5.229,0.99 1.833,0.198 10 false 16 3.927,0.792 5.76,0.99 1.833,0.198 10 false 17 3.958,1.448 5.792,1.646 1.833,0.198 10 false 22 3.948,2.813 5.781,3.01 1.833,0.198 10 false 53 3.948,4.198 5.781,4.396 1.833,0.198 10 false 32 1.813,5.146 3.646,5.344 1.833,0.198 10 false 25 1.385,5.25 3.219,5.448 1.833,0.198 10 false 2 0.198,5.24 2.031,5.438 1.833,0.198 10 false 1 0.198,5.51 2.031,5.708 1.833,0.198 10 false 3 3.969,5.667 5.802,5.865 1.833,0.198 10 false 28 3.99,6.188 5.823,6.385 1.833,0.198 10 false 6 3.948,6.646 5.781,6.844 1.833,0.198 10 false 18 3.375,6.656 5.208,6.854 1.833,0.198 10 false 17 6.24,5.677 7.156,5.896 0.917,0.219 10 false 1 6.24,6.646 7.156,6.865 0.917,0.219 10 false 17 6.24,7.094 7.156,7.313 0.917,0.219 10 false 28 6.24,7.542 7.156,7.76 0.917,0.219 10 false 10 6.24,7.927 7.156,8.146 0.917,0.219 10 false 27 6.302,2.813 7.156,3.063 0.854,0.25 10 false 1 6.24,1.708 7.156,1.927 0.917,0.219 10 false 18 6.24,0.781 7.156,1 0.917,0.219 10 false 18 0.406,4.656 2.24,4.854 1.833,0.198 10 false STOP

for RHD:
B501962E11
0.031,0.208 0.875,0.563 0.844,0.354 10 true from Auxiliary Battery 1.198,4.917 2.083,5.271 0.885,0.354 10 false from Auxiliary Battery 1.771,7.24 3.927,7.635 2.156,0.396 10 false Certification ECU (Smart Key ECU Assembly) 4.094,6.979 6.865,7.354 2.771,0.375 10 false Driver Side Junction Block Assembly 0.323,4.375 2.156,4.573 1.833,0.198 10 false D98 0.333,4.552 2.167,4.75 1.833,0.198 10 false Power Switch 0.271,6.333 2.104,6.531 1.833,0.198 10 false Stop Light Switch Assembly 0.292,6.188 2.125,6.385 1.833,0.198 10 false A3 1.792,3.375 3.625,3.573 1.833,0.198 10 false D86 1.781,2.74 3.615,2.938 1.833,0.198 10 false D86 1.792,4 3.625,4.198 1.833,0.198 10 false D86 1.802,5.583 3.635,5.781 1.833,0.198 10 false G37 1.792,0.25 3.625,0.448 1.833,0.198 10 false D86 1.792,1.26 3.625,1.458 1.833,0.198 10 false D86 3.365,0.781 5.198,0.979 1.833,0.198 10 false D86 3.375,6.646 5.208,6.844 1.833,0.198 10 false D86 3.031,5.74 4.865,5.938 1.833,0.198 10 false IC 2.448,6.542 4.281,6.74 1.833,0.198 10 false IC 3.052,3.021 4.885,3.219 1.833,0.198 10 false IC 2.448,0.677 4.281,0.875 1.833,0.198 10 false IC 2.833,0.302 4.667,0.5 1.833,0.198 10 false +B 2.896,0.719 4.729,0.917 1.833,0.198 10 false ACCD 1.031,2.635 2.865,2.833 1.833,0.198 10 false SS1 1.031,3.26 2.865,3.458 1.833,0.198 10 false SS2 2.146,3.281 3.979,3.479 1.833,0.198 10 false SSW2 2.156,2.646 3.99,2.844 1.833,0.198 10 false SSW1 2.188,3.885 4.021,4.083 1.833,0.198 10 false AGND 0.896,3.885 1.385,4.063 0.49,0.177 10 false AGND 2.198,0.26 4.031,0.458 1.833,0.198 10 false +B 2.677,2.125 4.51,2.323 1.833,0.198 10 false +B 2.813,6.156 4.646,6.354 1.833,0.198 10 false +B 2.906,6.552 3.313,6.729 0.406,0.177 10 false IG1D 2.156,5.479 3.99,5.677 1.833,0.198 10 false STP1 2.177,1.26 4.01,1.458 1.833,0.198 10 false E 3.906,0.781 5.74,0.979 1.833,0.198 10 false 4D 3.927,5.385 5.76,5.583 1.833,0.198 10 false 4D 3.927,5.896 5.76,6.094 1.833,0.198 10 false 4D 3.917,6.646 5.75,6.844 1.833,0.198 10 false 4D 3.927,4.167 5.76,4.365 1.833,0.198 10 false 4D 3.917,2.521 5.75,2.719 1.833,0.198 10 false 4A 3.906,1.292 5.74,1.49 1.833,0.198 10 false 4D 6.115,0.781 6.844,0.958 0.729,0.177 10 false 4A 6.104,6.635 7.156,6.833 1.052,0.198 10 false 4A 6.26,5.615 7.135,5.969 0.875,0.354 10 false from Auxiliary Battery 6.281,2.719 7.135,3.094 0.854,0.375 10 false from Auxiliary Battery 4.302,1.448 6.135,1.646 1.833,0.198 10 false ACC D 5.115,1.792 6.948,1.99 1.833,0.198 10 false ACC D 0.438,5.573 2.271,5.771 1.833,0.198 10 false B 1.219,5.49 3.052,5.688 1.833,0.198 10 false L 0.417,5.875 2.25,6.073 1.833,0.198 10 false GND 0.438,5.188 2.271,5.385 1.833,0.198 10 false STOP 1.24,0.385 3.073,0.583 1.833,0.198 10 false AM2 4.979,3.063 6.813,3.26 1.833,0.198 10 false IG1 D NO.2 4.969,4.698 6.802,4.896 1.833,0.198 10 false IG1 D NO.1 5.135,6.156 6.969,6.354 1.833,0.198 10 false IG2 D 4.302,4.292 4.75,4.844 0.448,0.552 10 false IG1 D NO.1 4.281,5.531 4.729,6.083 0.448,0.552 10 false IG2 D NO.2 4.302,2.677 4.75,3.229 0.448,0.552 10 false IG1 D NO.4 6.125,5.385 6.76,5.583 0.635,0.198 10 false 4L 6.083,2.521 7.135,2.719 1.052,0.198 10 false 4K 1.844,5.417 3.677,5.615 1.833,0.198 10 false 25 1.844,3.813 3.677,4.01 1.833,0.198 10 false 11 1.844,3.177 3.677,3.375 1.833,0.198 10 false 21 1.833,2.573 3.667,2.771 1.833,0.198 10 false 23 1.823,1.073 3.656,1.271 1.833,0.198 10 false 18 1.823,0.052 3.656,0.25 1.833,0.198 10 false 4 3.417,0.594 5.25,0.792 1.833,0.198 10 false 16 3.896,0.604 5.729,0.802 1.833,0.198 10 false 18 3.885,1.083 5.719,1.281 1.833,0.198 10 false 22 3.885,2.323 5.719,2.521 1.833,0.198 10 false 53 3.938,3.927 5.771,4.125 1.833,0.198 10 false 32 3.906,5.177 5.74,5.375 1.833,0.198 10 false 28 3.917,5.708 5.75,5.906 1.833,0.198 10 false 7 3.906,6.448 5.74,6.646 1.833,0.198 10 false 19 3.438,6.458 5.271,6.656 1.833,0.198 10 false 17 6.125,0.594 7.156,0.813 1.031,0.219 10 false 21 6.115,2.292 7.146,2.51 1.031,0.219 10 false 1 6.115,5.219 7.146,5.438 1.031,0.219 10 false 1 6.125,6.448 7.156,6.667 1.031,0.219 10 false 4 1.375,2.656 3.208,2.854 1.833,0.198 10 false 5 1.375,3.302 3.208,3.5 1.833,0.198 10 false 1 1.375,3.885 3.208,4.083 1.833,0.198 10 false 6 0.26,5.479 2.094,5.677 1.833,0.198 10 false 1 0.25,5.771 2.083,5.969 1.833,0.198 10 false 3 1.385,5.51 3.219,5.708 1.833,0.198 10 false 2

B604967E02
2.688,1.698 2.99,1.938 0.302,0.24 10 false D86 3.073,0.448 3.49,0.688 0.417,0.24 10 false CLG5 3.063,1.552 3.479,1.792 0.417,0.24 10 false CG5B 3.573,1.021 3.875,1.26 0.302,0.24 10 false IC 0.698,2.094 1.24,2.281 0.542,0.188 10 false D52 0.698,2.26 2.406,2.698 1.708,0.438 10 false No. 1 Indoor Electrical Key Antenna (Front Floor) 1.51,0.438 2.052,0.688 0.542,0.25 10 false ANTE5 1.573,1.604 1.99,1.844 0.417,0.24 10 false CLGB 2.063,3.198 2.365,3.438 0.302,0.24 10 false 1 2.063,4.354 2.365,4.594 0.302,0.24 10 false 3 2.781,0.354 3.083,0.594 0.302,0.24 10 false 8 2.771,1.5 3.073,1.74 0.302,0.24 10 false 9 1.51,3.208 2.073,3.521 0.563,0.313 10 false ANTE6 1.573,4.354 1.99,4.594 0.417,0.24 10 false CLGB 3.073,3.208 3.49,3.448 0.417,0.24 10 false CLG6 3.063,4.365 3.479,4.604 0.417,0.24 10 false CG6B 2.906,4.938 4.5,5.49 1.594,0.552 10 false Certification ECU (Smart Key ECU Assembly) 2.688,4.458 2.99,4.698 0.302,0.24 10 false G37 2.792,4.281 3.094,4.521 0.302,0.24 10 false 6 2.781,3.125 3.083,3.365 0.302,0.24 10 false 5 0.646,4.833 0.948,5.073 0.302,0.24 10 false G65 3.594,3.844 3.896,4.083 0.302,0.24 10 false IC 0.635,5.01 2.344,5.448 1.708,0.438 10 false No. 2 Indoor Electrical Key Antenna (Rear Floor) 2.688,3.323 2.99,3.563 0.302,0.24 10 false G37 2.688,0.542 2.99,0.781 0.302,0.24 10 false D86 2.052,0.438 2.354,0.677 0.302,0.24 10 false 1 2.052,1.594 2.354,1.833 0.302,0.24 10 false 3

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the ignition switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start. While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

Make sure that no DTCs are output. If any DTCs are output, proceed to Diagnostic Trouble Code Chart.

·

If the entry and start system (for Start Function) has been canceled, enable the system before performing troubleshooting.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>CUSTOMIZE PARAMETERS

·

Inspect the fuses of circuits related to this system before performing the following procedure.

·

Before replacing the certification ECU (smart key ECU assembly) or an electrical key transmitter sub-assembly, refer to the Service Bulletin.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>PRECAUTION

·

After completing repairs, confirm that the problem does not recur.

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".

·

An antenna coil is connected between the terminals of the indoor electrical key antenna.

·

The door control receiver is also involved in interior certification.



HINT:
·

If interior certification does not succeed, the History of Reason for Operation may remain in the certification ECU (smart key ECU assembly).

·

If the operation history remains, refer to the history table to determine the conditions and narrow down any trouble areas.



Body Electrical > Entry&Start > Utility
Tester Display
Operation History
50005 125 52

PROCEDURE

1.CHECK PUSH-BUTTON START FUNCTION
a.

Get into the vehicle while carrying the electrical key transmitter sub-assembly that has already been registered.


b.

Change the shift state to park (P).


c.

Check that the power source mode changes when the power switch is pressed without depressing the brake pedal.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>OPERATION CHECK


Result:
Result Proceed to
Power source mode changes only when the electrical key transmitter sub-assembly is inside the push-button start function operation range for the rear side A
Power source mode changes only when the electrical key transmitter sub-assembly is inside the push-button start function operation range for the front side B
Power source mode does not change C



A

2.CHECK WAVE ENVIRONMENT

B

6.CHECK WAVE ENVIRONMENT

C

10.CHECK TRANSMITTER BATTERY
2.CHECK WAVE ENVIRONMENT
a.

Install the transmitter battery to the electrical key transmitter sub-assembly.

Click hereGeneral>MAINTENANCE>TRANSMITTER BATTERY>REMOVAL


b.

Bring the electrical key transmitter sub-assembly near the No. 1 indoor electrical key antenna assembly (front floor) and perform an entry and start system check.

NOTICE:

Communication may not be possible if the electrical key transmitter sub-assembly is within 0.2 m (0.656 ft.) of the No. 1 indoor electrical key antenna assembly (front floor).

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>PARTS LOCATION



HINT:
·

As the effect of wave interference decreases by moving the electrical key transmitter sub-assembly close to each indoor electrical key antenna assembly, it may be possible to check whether wave interference is the cause of the problem.

·

If the inspection result is that the problem only occurs in certain locations or at certain times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.

·

There may be wave interference if the vehicle is near broadcasting antennas, large video displays, wireless garage door opener systems, wireless security cameras, home security systems, etc. In this case, move the vehicle to a different location and check if there is any improvement.



OK:

The hybrid control system starts when the electrical key transmitter sub-assembly is held near each indoor electrical key antenna assembly and the power switch is pressed with the brake pedal depressed.


Result:
Proceed to
OK
NG



OK

AFFECTED BY WAVE INTERFERENCE

NG

3.CHECK KEY DIAGNOSTIC MODE
3.CHECK KEY DIAGNOSTIC MODE
a.
B581609C01
0.646,1.146 2.667,0.406 2.667,0.406 3,0.406 false 2.073,1.167 2.656,0.417 false 3.042,0.333 3.271,0.583 0.229,0.25 10 false *a
*a Inspection Point

The illustrations shown are examples only.


Check the No. 1 indoor electrical key antenna assembly (front floor).

When the electrical key transmitter sub-assembly is at either inspection point, check that the wireless buzzer sounds.

HINT:
·

Select either channel 1 or channel 2 and perform the key diagnostic mode inspection for each channel.

·

If the buzzer sounds with [CH1] displayed but not with [CH2], the electrical key transmitter sub-assembly cannot be detected by channel 2 due to a malfunction, such as wave interference.

·

It is possible to check which No. 1 indoor electrical key antenna assembly (front floor) is operating by the sounding of the buzzer.

·

When the wireless buzzer does not sound for No. 1 indoor electrical key antenna assembly (front floor), it can be judged that the certification ECU (smart key ECU assembly), which controls the No. 1 indoor electrical key antenna assembly (front floor), is malfunctioning.




Body Electrical > Entry&Start > Utility
Tester Display
Communication Check(Key Diag Mode)
50005 125 143
Result:
Result Proceed to
The wireless buzzer sounds A
The wireless buzzer does not sound B



A

4.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (FRONT FLOOR))

B

AFFECTED BY WAVE INTERFERENCE

4.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (FRONT FLOOR))
a.

Disconnect the D86 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the D52 No. 1 indoor electrical key antenna assembly (front floor) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D86,D52)Location & Routing

Click Connector(D86)Instrument Panel>Instrument Panel Wire>Certification ECU

Click Connector(D52)Instrument Panel>Instrument Panel Wire>No. 1 Indoor Electrical Key Antenna Assembly

D86-8 (CLG5) - D52-1 (ANTE5) Always Below 1 Ω
D86-9 (CG5B) - D52-3 (CLGB) Always Below 1 Ω
D86-8 (CLG5) or D52-1 (ANTE5) - Other terminals and body ground Always 10 kΩ or higher
D86-9 (CG5B) or D52-3 (CLGB) - Other terminals and body ground Always 10 kΩ or higher



d.

Reconnect the D86 certification ECU (smart key ECU assembly) connector.


Result:
Proceed to
OK
NG



OK

5.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (FRONT FLOOR))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (FRONT FLOOR))
a.
B499319C01
0.313,0.344 0.625,0.5 0.313,0.156 10 false *a 1.125,2.406 1.438,2.563 0.313,0.156 10 false *b 2.219,2.406 2.531,2.563 0.313,0.156 10 false *c
*a Waveform
*b For 30 seconds after closing any door
*c After 30 seconds or more have elapsed since any door closed


Using an oscilloscope, check the waveform.

Measurement Condition:
Tester Connection Condition Tool Setting Specified Condition

Click Location & Routing(D52)Location & Routing

Click Connector(D52)Instrument Panel>Instrument Panel Wire>No. 1 Indoor Electrical Key Antenna Assembly

D52-1 (ANTE5) - D52-3 (CLGB) Procedure:
1.

Ignition switch off

2.

Electrical key transmitter sub-assembly not inside vehicle

3.

Within 30 seconds of closing any door


2 V/DIV., 500 ms./DIV. Pulse generation
(See waveform)


OK:

The waveform is similar to that shown in the illustration.



Result:
Proceed to
OK
NG



OK

REPLACE NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (FRONT FLOOR)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

6.CHECK WAVE ENVIRONMENT
a.

Install the transmitter battery to the electrical key transmitter sub-assembly.

Click hereGeneral>MAINTENANCE>TRANSMITTER BATTERY>REMOVAL


b.

Bring the electrical key transmitter sub-assembly near the No. 2 indoor electrical key antenna assembly (rear floor) and perform an entry and start system check.

HINT:

Check that the customize setting "Ignition Available Area" is set to "All".

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>CUSTOMIZE PARAMETERS


NOTICE:

Communication may not be possible if the electrical key transmitter sub-assembly is within 0.2 m (0.656 ft.) of the center of the No. 2 indoor electrical key antenna assembly (rear floor).

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>PARTS LOCATION



HINT:
·

As the effect of wave interference decreases by moving the electrical key transmitter sub-assembly close to each indoor electrical key antenna assembly, it may be possible to check whether wave interference is the cause of the problem.

·

If the inspection result is that the problem only occurs in certain locations or at certain times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.

·

There may be wave interference if the vehicle is near broadcasting antennas, large video displays, wireless garage door opener systems, wireless security cameras, home security systems, etc. In this case, move the vehicle to a different location and check if there is any improvement.



OK:

The hybrid control system starts when the electrical key transmitter sub-assembly is held near each indoor electrical key antenna assembly and the power switch is pressed with the brake pedal depressed.


Result:
Proceed to
OK
NG



OK

AFFECTED BY WAVE INTERFERENCE

NG

7.CHECK KEY DIAGNOSTIC MODE
7.CHECK KEY DIAGNOSTIC MODE
a.
B581610C01
0.688,0.375 2.677,1.417 2.677,1.417 3.01,1.417 false 2.042,0.396 2.667,1.417 false 3.052,1.344 3.281,1.594 0.229,0.25 10 false *a
*a Inspection Point

The illustrations shown are examples only.


Check the No. 2 indoor electrical key antenna assembly (rear floor).

When the electrical key transmitter sub-assembly is at either inspection point, check that the wireless buzzer sounds.

HINT:
·

Select either channel 1 or channel 2 and perform the key diagnostic mode inspection for each channel.

·

If the buzzer sounds with [CH1] displayed but not with [CH2], the electrical key transmitter sub-assembly cannot be detected by channel 2 due to a malfunction, such as wave interference.

·

It is possible to check which No. 2 indoor electrical key antenna assembly (rear floor) is operating by the sounding of the buzzer.

·

When the wireless buzzer does not sound for No. 2 indoor electrical key antenna assembly (rear floor), it can be judged that the certification ECU (smart key ECU assembly), which controls the No. 2 indoor electrical key antenna assembly (rear floor), is malfunctioning.




Body Electrical > Entry&Start > Utility
Tester Display
Communication Check(Key Diag Mode)
50005 125 143
Result:
Result Proceed to
The wireless buzzer sounds A
The wireless buzzer does not sound B



A

8.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - NO. 2 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (REAR FLOOR))

B

AFFECTED BY WAVE INTERFERENCE

8.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - NO. 2 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (REAR FLOOR))
a.

Disconnect the G37 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the G65 No. 2 indoor electrical key antenna assembly (rear floor) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(G37,G65)Location & Routing

Click Connector(G37)Instrument Panel>Floor Wire>Certification ECU

Click Connector(G65)Body>Floor Wire / No. 3 Floor Wire>No. 2 Indoor Electrical Key Antenna Assembly

G37-5 (CLG6) - G65-1 (ANTE6) Always Below 1 Ω
G37-6 (CG6B) - G65-3 (CLGB) Always Below 1 Ω
G37-5 (CLG6) or G65-1 (ANTE6) - Other terminals and body ground Always 10 kΩ or higher
G37-6 (CG6B) or G65-3 (CLGB) - Other terminals and body ground Always 10 kΩ or higher



d.

Reconnect the G37 certification ECU (smart key ECU assembly) connector.


Result:
Proceed to
OK
NG



OK

9.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO NO. 2 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (REAR FLOOR))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO NO. 2 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (REAR FLOOR))
a.
B499319C01
0.313,0.344 0.625,0.5 0.313,0.156 10 false *a 1.125,2.406 1.438,2.563 0.313,0.156 10 false *b 2.219,2.406 2.531,2.563 0.313,0.156 10 false *c
*a Waveform
*b For 30 seconds after closing any door
*c After 30 seconds or more have elapsed since any door closed


Using an oscilloscope, check the waveform.

Measurement Condition:
Tester Connection Condition Tool Setting Specified Condition

Click Location & Routing(G65)Location & Routing

Click Connector(G65)Body>Floor Wire / No. 3 Floor Wire>No. 2 Indoor Electrical Key Antenna Assembly

G65-1 (ANTE6) - G65-3 (CLGB) Procedure:
1.

Ignition switch off

2.

Electrical key transmitter sub-assembly not inside vehicle

3.

Within 30 seconds of closing any door


2 V/DIV., 500 ms./DIV. Pulse generation
(See waveform)


OK:

The waveform is similar to that shown in the illustration.



Result:
Proceed to
OK
NG



OK

REPLACE NO. 2 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (REAR FLOOR)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

10.CHECK TRANSMITTER BATTERY
a.

Check the transmitter battery level of the electrical key transmitter sub-assembly that was checked first.

i.

Press and hold the lock switch of the electrical key transmitter sub-assembly for 5 seconds and check the number of times that the LED illuminates.

HINT:
·

The electrical key transmitter sub-assembly sends voltage information to the certification ECU (smart key ECU assembly) when it is being used. "Yes" is displayed for the Data List item "Key Low Battery" when this voltage information indicates 2.2 V or less.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>DATA LIST / ACTIVE TEST

·

Even if the transmitter battery is depleted, it is still possible to start the hybrid control system by holding the electrical key transmitter sub-assembly near the power switch, depressing the brake pedal and pressing the power switch.





Result:
Result Proceed to
LED illuminates 3 times or more when switch is pressed and held A
LED does not illuminate when switch is pressed and held B
LED illuminates once or twice but not a third time C



A

11.CHECK ENTRY LOCK / UNLOCK FUNCTION

B

17.INSPECT TRANSMITTER BATTERY

C

REPLACE TRANSMITTER BATTERY

11.CHECK ENTRY LOCK / UNLOCK FUNCTION
a.

Check that the entry lock and unlock functions operate on each door.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK

HINT:

If the door control receiver is defective, code verification does not begin in the cabin and the entry lock and unlock functions do not operate.



Result:
Result Proceed to
Entry lock/unlock functions operate normally A
An entry lock/unlock functions does not operate normally B



A

12.READ VALUE USING GTS (START SWITCH1, START SWITCH2)

B

GO TO ENTRY AND START SYSTEM (for Entry Function) (All door entry lock/unlock functions and wireless functions do not operate)

12.READ VALUE USING GTS (START SWITCH1, START SWITCH2)
a.

Read the Data List according to the display on the GTS.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Start Switch1 Power switch 1 status OFF or ON OFF: Power switch not pressed
ON: Power switch pressed
·

If the power switch is pressed for a short time, the display may not change.

·

Use this item to determine if the power switch input signal is malfunctioning.


Start Switch2 Power switch 2 status OFF or ON OFF: Power switch not pressed
ON: Power switch pressed
·

Backup for power switch 1. However, when the power switch is pressed and held, the power source mode can only be changed when both power switch 1 and 2 are normal..

·

Behaves the same way as power switch 1.


Body Electrical > Power Source Control > Data List
Tester Display
Start Switch1
Start Switch2
50003 223 4,5
OK:

The GTS display changes correctly in response to the power switch operation.



Result:
Proceed to
OK
NG



OK

13.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

15.INSPECT POWER SWITCH
13.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Measure the voltage while confirming the power source mode on the Data List.

B427583C95
4.531,0.417 4.948,0.667 0.417,0.25 4.667,2.167 4.333,2.167 4.333,2.167 4.333,1.208 false 4,2.167 4.25,2.167 4.25,2.167 4.25,1.208 false 0.396,0.177 0.708,0.333 0.313,0.156 10 false *a 4.615,0.438 5.115,0.646 0.5,0.208 10 false D86 3.667,2.083 4.167,2.292 0.5,0.208 10 false IG1D 4.75,2.083 5.25,2.292 0.5,0.208 10 false ACCD
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))
- -


Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Power Supply Condition Power supply state All OFF, ACC ON, IG ON or ST ON All OFF: Ignition switch off
ACC ON: Ignition switch ACC
IG ON: Ignition switch ON
ST ON: Sending hybrid control system start request signal
-
Body Electrical > Power Source Control > Data List
Tester Display
Power Supply Condition
50003 223 18
Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(D86)Location & Routing

Click Connector(D86)Instrument Panel>Instrument Panel Wire>Certification ECU

D86-17 (IG1D) - Body ground Ignition switch off 1 V or less
Ignition switch ACC
Ignition switch ON 9 V or higher
D86-16 (ACCD) - Body ground Ignition switch off 1 V or less
Ignition switch ACC 8.5 V or higher
Ignition switch ON



Result:
Proceed to
OK
NG



OK

14.CHECK HARNESS AND CONNECTOR (DRIVER SIDE JUNCTION BLOCK ASSEMBLY - BODY GROUND)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

14.CHECK HARNESS AND CONNECTOR (DRIVER SIDE JUNCTION BLOCK ASSEMBLY - BODY GROUND)
a.
C376684C30
1.51,0.26 1.938,0.458 0.427,0.198 1.656,0.271 1.969,0.469 0.313,0.198 10 false 4D 0.146,0.229 0.458,0.427 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to Driver Side Junction Block Assembly)


Disconnect the driver side junction block assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD:
Tester Connection Condition Specified Condition
4D-6 - Body ground Always Below 1 Ω

for RHD:
Tester Connection Condition Specified Condition
4D-7 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE DRIVER SIDE JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

15.INSPECT POWER SWITCH

Click hereEngine / Hybrid System>STARTING>POWER SWITCH>INSPECTION

Result:
Proceed to
OK
NG



OK

16.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - POWER SWITCH)

NG

16.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - POWER SWITCH)
a.

Disconnect the D86 certification ECU (smart key ECU assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D86,D98)Location & Routing

Click Connector(D86)Instrument Panel>Instrument Panel Wire>Certification ECU

Click Connector(D98)Instrument Panel>Instrument Panel Wire>Power Switch

D86-23 (SSW1) - D98-5 (SS1) Always Below 1 Ω
D86-21 (SSW2) - D98-1 (SS2) Always Below 1 Ω
D86-11 (AGND) - D98-6 (AGND) Always Below 1 Ω
D86-23 (SSW1) or D98-5 (SS1) - Other terminals and body ground Always 10 kΩ or higher
D86-21 (SSW2) or D98-1 (SS2) - Other terminals and body ground Always 10 kΩ or higher
D86-11 (AGND) or D98-6 (AGND) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

17.INSPECT TRANSMITTER BATTERY
a.

Inspect the transmitter battery.

Click hereVehicle Interior>DOOR LOCK>DOOR CONTROL TRANSMITTER>INSPECTION

NOTICE:

Do not wrap the lead wire around a terminal, wedge it between terminals, or solder it. The terminal may be deformed or damaged, and the transmitter battery will not be able to be installed correctly.



Result:
Proceed to
OK
NG



OK

REPLACE ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY

NG

REPLACE TRANSMITTER BATTERY