Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Start Function)
RM37H0E _58 Vehicle Interior _095303 THEFT DETERRENT / KEYLESS ENTRY _0449817 ENTRY AND START SYSTEM(for Start Function) C

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function)  B2282  Vehicle Speed Signal Malfunction  B2283  Vehicle Speed Sensor Malfunction  


DESCRIPTION

DTC B2282 is stored when the vehicle speed signal sent by the combination meter assembly via direct line and the vehicle speed signal sent via CAN communication do not match.

DTC B2283 is stored when a malfunction in the vehicle speed sensor is detected.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority Note
B2282 Vehicle Speed Signal Malfunction The vehicle speed signal sent by the combination meter assembly via direct line and the vehicle speed signal sent via CAN communication do not match. (1-trip detection logic*)
·

Meter/gauge system

·

Certification ECU (smart key ECU assembly)

·

Harness or connector


Power Source Control A
DTC Output Confirmation Operation:

Drive the vehicle at a vehicle speed of 25 km/h (16 mph) or more for 20 seconds, and then drive the vehicle at a vehicle speed of less than 5 km/h (3 mph) for 20 seconds.


B2283 Vehicle Speed Sensor Malfunction Vehicle speed signal malfunction is detected (excessive deceleration is detected). (1-trip detection logic*)
·

Meter/gauge system

·

Certification ECU (smart key ECU assembly)

·

Harness or connector


Power Source Control A
DTC Output Confirmation Operation:

Drive the vehicle at a vehicle speed of 50 km/h (31 mph) or more for 10 seconds.



*: Only detected while a malfunction is present.


Vehicle Condition and Fail-safe Function when Malfunction Detected
DTC Code Vehicle Condition when Malfunction Detected Fail-safe Function when Malfunction Detected
B2282
·

When the signal sent via either direct line or CAN communication is malfunctioning and indicates that the vehicle speed is 0 km/h (0 mph), there is no effect on vehicle behavior.

·

When the signal sent via either direct line or CAN communication is malfunctioning and indicates that the vehicle is moving, the ignition switch cannot be turned from ON to off.


-
B2283
·

The power source mode is changed to off (the hybrid control system is stopped) by pressing the power switch while the vehicle is being driven.

·

With the electrical key transmitter sub-assembly in the cabin, even if a hybrid control system start operation is performed, the hybrid control system will not start.


Steering lock motor operation is prohibited.

Related Data List and Active Test Items
DTC No. Data List and Active Test
B2282
B2283
Power Source Control
·

Vehicle Speed Signal

·

Power Supply Condition


Combination Meter
·

Vehicle Speed Meter



WIRING DIAGRAM

B559942E04
4.781,2.375 5.24,2.573 0.458,0.198 10 false D86 0.833,2.219 2.875,2.427 2.042,0.208 10 false Combination Meter Assembly 0.844,2.052 1.302,2.25 0.458,0.198 10 false D41 4.781,2.531 6.583,2.979 1.802,0.448 10 false Certification ECU (Smart Key ECU Assembly) 0.646,3.969 1.104,4.167 0.458,0.198 10 false G54 0.646,4.125 3.792,4.646 3.146,0.521 10 false Stereo Component Amplifier Assembly 0.885,5.865 2.927,6.073 2.042,0.208 10 false Navigation ECU*1 0.885,5.708 1.344,5.906 0.458,0.198 10 false D65 5.115,4.135 6.99,4.406 1.875,0.271 10 false Radio Receiver Assembly 5.115,3.979 6.042,4.167 0.927,0.188 10 false D61*1, D54*2 0.802,6.198 2.844,6.406 2.042,0.208 10 false : CAN Communication Line 5.479,0.927 5.938,1.125 0.458,0.198 10 false +B 5.229,1.344 5.688,1.542 0.458,0.198 10 false SPD 5.271,3.458 5.729,3.656 0.458,0.198 10 false SPD 1.885,5.24 2.344,5.438 0.458,0.198 10 false SPD 1.927,3.479 2.385,3.677 0.458,0.198 10 false SPD 4.969,1.292 5.427,1.49 0.458,0.198 10 false 19 2.313,1.313 2.771,1.51 0.458,0.198 10 false 19 2.052,1.333 2.51,1.531 0.458,0.198 10 false +S 2.302,3.333 2.76,3.531 0.458,0.198 10 false 17 2.313,5.094 2.771,5.292 0.458,0.198 10 false 9 4.969,3.302 5.427,3.5 0.458,0.198 10 false 27 5.813,1.635 6.271,1.833 0.458,0.198 10 false IC 6.229,1.948 6.688,2.146 0.458,0.198 10 false 18 5.979,2.083 6.438,2.281 0.458,0.198 10 false E 2.906,5.063 3.219,5.26 0.313,0.198 10 false *1 4.771,5.76 7.156,5.979 2.385,0.219 10 false *1: w/ Navigation System 4.771,6.188 7.156,6.406 2.385,0.219 10 false *2: w/o Navigation System

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the ignition switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start. While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

The entry and start system (for Start Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before replacing the certification ECU (smart key ECU assembly), refer to the Service Bulletin.

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".



PROCEDURE

1.READ VALUE USING GTS (VEHICLE SPEED METER)
a.

Read the Data List according to the display on the GTS.

Body Electrical > Combination Meter > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Vehicle Speed Meter Vehicle speed Min.: 0, Max.: 255 Almost same as actual vehicle speed (Speedometer tester) -
Body Electrical > Combination Meter > Data List
Tester Display
Vehicle Speed Meter
50003 409 23
HINT:

Using a speedometer tester, check the actual vehicle speed and the vehicle speed displayed on the GTS.


OK:

Vehicle speed displayed on the GTS is almost the same as the actual vehicle speed measured using a speedometer tester.



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING GTS (VEHICLE SPEED SIGNAL)

NG

GO TO METER / GAUGE SYSTEM (Speedometer Malfunction)

2.READ VALUE USING GTS (VEHICLE SPEED SIGNAL)
a.

Read the Data List according to the display on the GTS.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Vehicle Speed Signal Vehicle being driven or stopped Stop or Run Stop: Vehicle stopped
Run: Vehicle being driven at 5 km/h (3 mph) or more
-
Body Electrical > Power Source Control > Data List
Tester Display
Vehicle Speed Signal
50003 223 16
OK:

The GTS display changes correctly in response to the vehicle condition.



Result:
Proceed to
OK
NG



OK

GO TO METER / GAUGE SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

NG

3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - COMBINATION METER ASSEMBLY)
3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - COMBINATION METER ASSEMBLY)

*1: w/ Navigation System

*2: w/o Navigation System


Pre-procedure1

a.

Disconnect the D86 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the D41 combination meter assembly connector.


c.

Disconnect the G54 stereo component amplifier assembly connector.


d.

Disconnect the D65 navigation ECU connector.*1


e.

Disconnect the D61*1, D54*2 radio receiver assembly connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D41,D86)Location & Routing

Click Connector(D41)Instrument Panel>Instrument Panel Wire>Combination Meter Assembly

Click Connector(D86)Instrument Panel>Instrument Panel Wire>Certification ECU

D41-19 (+S) - D86-19 (SPD) Always Below 1 Ω
D41-19 (+S) or D86-19 (SPD) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

a.

None.



OK

4.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

Pre-procedure1

a.

Reconnect the D86 certification ECU (smart key ECU assembly) connector.


b.

Reconnect the D41 combination meter assembly connector.


Procedure1

a.

Using an oscilloscope, check the waveform.

B424430C61
1.927,0.417 2.344,0.667 0.417,0.25 2.854,2.115 2.604,2.115 2.604,2.115 2.604,1.365 true 2.771,2.365 2.521,2.365 2.521,2.365 2.521,1.365 true 0.104,0.167 0.417,0.365 0.313,0.198 10 false *a 2.01,0.448 2.323,0.646 0.313,0.198 10 false D86 2.917,2.052 3.229,2.25 0.313,0.198 10 false E 2.813,2.302 3.219,2.5 0.406,0.198 10 false SPD 6.573,1.49 6.958,1.698 0.385,0.208 10 false GND 4.302,0.406 4.615,0.604 0.313,0.198 10 false *b
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))
*b Waveform


Measurement Condition:
Tester Connection Condition Tool Setting Specified Condition

Click Location & Routing(D86)Location & Routing

Click Connector(D86)Instrument Panel>Instrument Panel Wire>Certification ECU

D86-19 (SPD) - D86-18 (E) Vehicle being driven at approximately 5 km/h (3 mph) 5 V/DIV., 20 ms./DIV. Pulse generation
(See waveform)


HINT:

The wavelength becomes shorter as the vehicle speed increases.


OK:

The waveform is similar to that shown in the illustration.



Result:
Proceed to
OK
NG


Post-procedure1

a.

None.



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

GO TO METER / GAUGE SYSTEM (Speed Signal Circuit)