Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM
RM37H0E _58 Vehicle Interior _095316 METER / GAUGE / DISPLAY _0455143 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Speedometer Malfunction  


DESCRIPTION

The combination meter assembly receives vehicle speed signals from the brake actuator assembly (No. 2 skid control ECU) via CAN communication. The speed sensor detects the wheel speed and sends the appropriate signals to the brake actuator assembly (No. 2 skid control ECU). The brake actuator assembly (No. 2 skid control ECU) supplies power to the vehicle speed sensor. The brake actuator assembly (No. 2 skid control ECU) detects vehicle speed signals based on pulses of the voltage.

HINT:
·

Factors that affect the indicated vehicle speed include the tire size, tire inflation, and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using the GTS. For details about testing and the margin of error, see the reference chart.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>OPERATION CHECK

·

If the vehicle speed sensor circuit has a malfunction, the brake actuator assembly (No. 2 skid control ECU) stores DTCs. Troubleshoot the electronically controlled brake system.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING



WIRING DIAGRAM

E230682E60
0.958,1.708 2.823,2.146 1.865,0.438 10 false Brake Actuator Assembly (No. 2 Skid Control ECU) 4.313,1.708 6.177,1.938 1.865,0.229 10 false Combination Meter Assembly 1.208,2.365 2.979,2.542 1.771,0.177 10 false : CAN Communication Line

CAUTION / NOTICE / HINT

NOTICE:
·

If the vehicle speed is outside the allowable range when tested, perform the operation check.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>OPERATION CHECK

·

When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING



HINT:

Before starting the following inspection, check tire size and tire air pressure.


PROCEDURE

1.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > Combination Meter > Trouble Codes
50001 409

Result:
Result Proceed to
DTCs are not output. A
DTCs are output. B



A

2.CHECK FOR DTC (ELECTRONICALLY CONTROLLED BRAKE SYSTEM)

B

2.CHECK FOR DTC (ELECTRONICALLY CONTROLLED BRAKE SYSTEM)
a.

Check for DTCs.

Chassis > Brake/EPB > Trouble Codes
50001 435

Result:
Result Proceed to
DTCs are not output. A
DTCs are output. B



A

3.READ VALUE USING GTS (VEHICLE SPEED METER)

B

3.READ VALUE USING GTS (VEHICLE SPEED METER)
a.

Using the GTS, read the Data List.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST

Body Electrical > Combination Meter > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Vehicle Speed Meter Vehicle speed Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph) Almost the same as actual vehicle speed -
Body Electrical > Combination Meter > Data List
Tester Display
Vehicle Speed Meter
50003 122 8
HINT:
·

When the Data List values of the ECUs match, an internal malfunction of the combination meter assembly is suspected.

·

When the Data List values of the ECUs do not match, a signal output error of the brake actuator assembly (No. 2 skid control ECU) or an internal malfunction of the combination meter assembly is suspected.



OK:

Vehicle speed displayed on the GTS is almost the same as the actual vehicle speed measured using a speedometer tester (calibrated chassis dynamometer).



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

4.READ VALUE USING GTS (VEHICLE SPEED)
4.READ VALUE USING GTS (VEHICLE SPEED)
a.

Using the GTS, read the Data List.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST

Chassis > Brake/EPB > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Vehicle Speed Vehicle speed
(Vehicle speed signal output to combination meter assembly)
Min.: 0.0 km/h (0 mph), Max.: 6553.5 km/h (4072 mph) Vehicle stopped: 0.0 km/h (0 mph) When driving at constant speed: No large fluctuations
Chassis > Brake/EPB > Data List
Tester Display
Vehicle Speed
50003 435 36
OK:

Vehicle speed displayed on the GTS is almost the same as the actual vehicle speed measured using a speedometer tester (calibrated chassis dynamometer).



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG