Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM
RM37H0E _58 Vehicle Interior _095316 METER / GAUGE / DISPLAY _0455143 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Speed Signal Circuit  


DESCRIPTION

The combination meter assembly receives the vehicle speed signal from this circuit. The wheel speed sensors produce an output that varies according to the vehicle speed. The wheel speed sensor output is received by the brake actuator assembly (No. 2 skid control ECU) assembly which uses this information to create the vehicle speed signal*a. The vehicle speed signal consists of pulses sent to the combination meter assembly from the brake actuator assembly (No. 2 skid control ECU) assembly. To create this signal, 12 V is output from IG2 which is behind a resistor in the combination meter assembly. This voltage is sent to the brake actuator assembly (No. 2 skid control ECU) assembly. The pulse signal is created by switching the transistor in the brake actuator assembly (No. 2 skid control ECU) assembly on and off, making the voltage on the wire drop to 0 V. A similar system is used for the output of this signal from the combination meter assembly via terminal +S. A voltage of 12 V or 5 V is applied to terminal +S from each ECU or relay that is connected to this terminal. The transistor in the combination meter assembly is controlled by the signal from the brake actuator assembly (No. 2 skid control ECU) assembly. When this transistor is turned on, this transistor makes the voltage supplied by the various ECUs (via their respective internal resistors) drop to 0 V. Each ECU connected to terminal +S of the combination meter assembly controls its respective system based on this pulse signal.

*a: This vehicle speed signal is created by the brake actuator assembly (No. 2 skid control ECU) assembly. There is no actual component that is referred to as the vehicle speed sensor. In addition, for some systems, vehicle speed information may be received via CAN communication.


HINT:

This circuit is used for the systems connected to terminal +S. This signal is not used for combination meter assembly operation. Combination meter assembly components such as the speedometer operate using data received via CAN communication.


WIRING DIAGRAM

E462764E03
0.698,1.458 3.896,1.688 3.198,0.229 10 false Brake Actuator Assembly (No. 2 Skid Control ECU) 0.719,3.135 3.594,3.448 2.875,0.313 10 false Certification ECU (Smart Key ECU Assembly) 0.74,4.573 3.271,4.792 2.531,0.219 10 false Stereo Component Amplifier Assembly*1 0.75,6.135 1.896,6.333 1.146,0.198 10 false Navigation ECU*1 5.281,3.167 7.135,3.396 1.854,0.229 10 false Combination Meter Assembly 1.469,2.49 1.875,2.688 0.406,0.198 10 false SPD 1.865,3.906 2.271,4.104 0.406,0.198 10 false 17 1.448,5.479 1.854,5.677 0.406,0.198 10 false SPD 5.375,3.896 5.781,4.094 0.406,0.198 10 false SPD 5.365,2.479 5.604,2.688 0.24,0.208 10 false +S 5.365,0.448 5.573,0.635 0.208,0.188 10 false SI 0.698,1.302 0.969,1.49 0.271,0.188 10 false A6 1.49,0.458 1.833,0.656 0.344,0.198 10 false SP1 1.854,0.458 2.083,0.656 0.229,0.198 10 false 18 1.854,2.49 2.26,2.688 0.406,0.198 10 false 19 0.719,2.979 1.042,3.156 0.323,0.177 10 false D86 0.74,4.417 1.063,4.604 0.323,0.188 10 false G54 1.479,3.906 1.885,4.104 0.406,0.198 10 false SPD 0.75,5.979 1.052,6.177 0.302,0.198 10 false D65 1.875,5.479 2.281,5.677 0.406,0.198 10 false 9 4.656,4.406 4.969,4.583 0.313,0.177 10 false D54 5.125,3.906 5.531,4.104 0.406,0.198 10 false 27 5.094,2.469 5.302,2.667 0.208,0.198 10 false 19 5.104,0.448 5.302,0.635 0.198,0.188 10 false 20 5.125,5.479 5.531,5.677 0.406,0.198 10 false 27 5.354,5.479 5.76,5.677 0.406,0.198 10 false SPD 5.323,6.146 7.073,6.354 1.75,0.208 10 false Radio Receiver Assembly*1 5.323,5.99 5.667,6.167 0.344,0.177 10 false D61 0.167,7.594 1.74,7.792 1.573,0.198 10 false *1: w/ Navigation System 0.156,8.156 1.833,8.365 1.677,0.208 10 false *2: w/o Navigation System 4.656,4.573 7.146,4.792 2.49,0.219 10 false Radio and Display Receiver Assembly*2 5.292,3.031 5.573,3.229 0.281,0.198 10 false D41

CAUTION / NOTICE / HINT

NOTICE:
·

Before replacing the certification ECU (smart key ECU assembly), refer to Service Bulletin.

·

When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.



PROCEDURE

1.INSPECT ECU TERMINAL VOLTAGE (INPUT VOLTAGE)
a.

Disconnect the D41 combination meter assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(D41)Location & Routing

Click Connector(D41)Instrument Panel>Instrument Panel Wire>Combination Meter Assembly

D41-19 (+S) - Body ground Ignition switch ON 4.5 to 14 V


HINT:

If any of the ECUs specified in the wiring diagram supplies power to the combination meter assembly, the combination meter assembly will output a waveform.



Result:
Proceed to
OK
NG



OK

2.INSPECT COMBINATION METER ASSEMBLY (OUTPUT VOLTAGE)

NG

5.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - EACH ECU)
2.INSPECT COMBINATION METER ASSEMBLY (OUTPUT VOLTAGE)
a.

Disconnect the A6 brake actuator assembly (No.2 skid control ECU).


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(A6)Location & Routing

Click Connector(A6)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Brake Actuator Assembly

A6-18 (SP1) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.INSPECT COMBINATION METER ASSEMBLY (INPUT WAVEFORM)

NG

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - SKID CONTROL ECU ASSEMBLY)
3.INSPECT COMBINATION METER ASSEMBLY (INPUT WAVEFORM)
a.
E457496C01
1.479,0.469 1.844,0.698 0.365,0.229 0.479,1.99 0.771,1.302 true 0.146,0.156 0.635,0.469 0.49,0.313 10 false *a 0.427,2.031 0.854,2.26 0.427,0.229 10 false SI 2.76,3.646 3.406,3.917 0.646,0.271 10 false GND 1.521,0.5 1.875,0.708 0.354,0.208 10 false D41 0.896,3.76 1.385,4.073 0.49,0.313 10 false A 0.167,2.49 0.656,2.802 0.49,0.313 10 false *b
*a Component with harness connected
(Combination Meter Assembly)
*b Wave form


Check the input waveform.

i.

Remove the combination meter assembly with the connector(s) still connected.


ii.

Connect an oscilloscope to terminal D41-20 (SI) and body ground.


iii.

Turn the ignition switch ON.


iv.

Turn a wheel slowly.


v.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Tool setting 5 V/DIV., 20 ms./DIV.
Vehicle condition Ignition switch ON, wheel being rotated

OK:

The waveform is similar to that shown in the illustration.


HINT:

When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.




Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - SKID CONTROL ECU ASSEMBLY)
a.

Disconnect the D41 combination meter assembly connector.


b.

Disconnect the A6 brake actuator assembly (No. 2 skid control ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D41,A6)Location & Routing

Click Connector(D41)Instrument Panel>Instrument Panel Wire>Combination Meter Assembly

Click Connector(A6)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Brake Actuator Assembly

D41-20 (SI) - A6-18(SP1) Always Below 1 Ω
D41-20 (SI) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - EACH ECU)

*1: w/ Navigation System

*2: w/o Navigation System


a.

Disconnect the D41 combination meter assembly connector.


b.

Disconnect the D86 certification ECU (smart key ECU assembly) connector.


c.

Disconnect the G54 stereo component amplifier assembly connector*1.


d.

Disconnect the D65 navigation ECU connector*1.


e.

Disconnect the D61 radio receiver assembly connector*1.


f.

Disconnect the D54 radio and display receiver assembly connector*2.


g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D41)Location & Routing

Click Connector(D41)Instrument Panel>Instrument Panel Wire>Combination Meter Assembly

D41-19 (+S) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK VEHICLE TYPE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK VEHICLE TYPE
a.

Check vehicle condition.


Result:
Result Proceed to
w/ Navigation System A
w/o Navigation System B



A

7.INSPECT RADIO RECEIVER ASSEMBLY (SHORT CIRCUIT IN RADIO RECEIVER ASSEMBLY)

B

10.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY (SHORT CIRCUIT IN RADIO AND DISPLAY RECEIVER ASSEMBLY)
7.INSPECT RADIO RECEIVER ASSEMBLY (SHORT CIRCUIT IN RADIO RECEIVER ASSEMBLY)
a.

Disconnect the D41 combination meter assembly connector.


b.

Disconnect the D61 radio receiver assembly connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(D41)Location & Routing

Click Connector(D41)Instrument Panel>Instrument Panel Wire>Combination Meter Assembly

D41-19 (+S) - Body ground Ignition switch ON 4.5 to 14 V


HINT:

If the result is as specified, there may be a short circuit in the radio receiver assembly.



Result:
Proceed to
OK
NG



OK

REPLACE RADIO RECEIVER ASSEMBLY

NG

8.INSPECT STEREO COMPONENT AMPLIFIER ASSEMBLY (SHORT CIRCUIT IN STEREO COMPONENT AMPLIFIER ASSEMBLY)
8.INSPECT STEREO COMPONENT AMPLIFIER ASSEMBLY (SHORT CIRCUIT IN STEREO COMPONENT AMPLIFIER ASSEMBLY)
a.

Disconnect the D41 combination meter assembly connector.


b.

Disconnect the G54 stereo component amplifier assembly connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(D41)Location & Routing

Click Connector(D41)Instrument Panel>Instrument Panel Wire>Combination Meter Assembly

D41-19 (+S) - Body ground Ignition switch ON 4.5 to 14 V


HINT:

If the result is as specified, there may be a short circuit in the stereo component amplifier assembly.



Result:
Proceed to
OK
NG



OK

REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY

NG

9.INSPECT NAVIGATION ECU (SHORT CIRCUIT IN NAVIGATION ECU)
9.INSPECT NAVIGATION ECU (SHORT CIRCUIT IN NAVIGATION ECU)
a.

Disconnect the D41 combination meter assembly connector.


b.

Disconnect the D65 navigation ECU connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(D41)Location & Routing

Click Connector(D41)Instrument Panel>Instrument Panel Wire>Combination Meter Assembly

D41-19 (+S) - Body ground Ignition switch ON 4.5 to 14 V


HINT:

If the result is as specified, there may be a short circuit in the navigation ECU.



Result:
Proceed to
OK
NG



OK

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

10.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY (SHORT CIRCUIT IN RADIO AND DISPLAY RECEIVER ASSEMBLY)
a.

Disconnect the D41 combination meter assembly connector.


b.

Disconnect the D54 radio and display receiver assembly connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(D41)Location & Routing

Click Connector(D41)Instrument Panel>Instrument Panel Wire>Combination Meter Assembly

D41-19 (+S) - Body ground Ignition switch ON 4.5 to 14 V


HINT:

If the result is as specified, there may be a short circuit in the radio receiver assembly.



Result:
Proceed to
OK
NG



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)