Home › Vehicle Interior › DOOR LOCK › POWER DOOR LOCK CONTROL SYSTEM
RM37H0E _58 Vehicle Interior _095313 DOOR LOCK _0452394 POWER DOOR LOCK CONTROL SYSTEM U

DOOR LOCK  POWER DOOR LOCK CONTROL SYSTEM  TERMINALS OF ECU  


CHECK DRIVER SIDE JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)


E453982C08
1.083,3.198 1.49,3.458 0.406,0.26 3.24,3.198 3.646,3.458 0.406,0.26 5.448,3.208 5.854,3.469 0.406,0.26 3.24,7.708 3.646,7.969 0.406,0.26 1.823,4.542 2.229,4.802 0.406,0.26 5.385,4.479 5.792,4.74 0.406,0.26 1.125,6.177 1.531,6.438 0.406,0.26 3.573,6.115 3.979,6.375 0.406,0.26 6.25,6.146 6.656,6.406 0.406,0.26 5.271,6.146 5.677,6.406 0.406,0.26 1.625,1.781 1.906,1.781 false 1.625,1.427 1.906,1.427 false 1.625,1.115 1.906,1.115 false 1.573,0.604 1.573,0.24 1.573,0.24 1.781,0.24 false 1.99,1.729 2.302,1.927 0.313,0.198 10 false D14 1.979,1.063 2.292,1.26 0.313,0.198 10 false D12 1.99,1.375 2.302,1.573 0.313,0.198 10 false D11 3.75,0.927 3.906,1.125 0.156,0.198 10 false A 1.833,0.177 2.146,0.375 0.313,0.198 10 false *1 5.531,3.271 5.844,3.469 0.313,0.198 10 false D12 3.323,3.271 3.635,3.469 0.313,0.198 10 false D11 1.177,3.271 1.49,3.469 0.313,0.198 10 false D14 3.417,7.76 3.573,7.958 0.156,0.198 10 false A 0.833,1.031 1.146,1.229 0.313,0.198 10 false 4H 0.854,1.646 1.167,1.844 0.313,0.198 10 false 4F 0.854,2.01 1.167,2.208 0.313,0.198 10 false 4L 0.865,2.229 1.177,2.427 0.313,0.198 10 false 4K 5.823,1.042 6.135,1.24 0.313,0.198 10 false 4D 5.813,1.615 6.125,1.813 0.313,0.198 10 false 4A 1.958,4.615 2.271,4.813 0.313,0.198 10 false 4A 5.51,4.542 5.823,4.74 0.313,0.198 10 false 4D 1.271,6.24 1.583,6.438 0.313,0.198 10 false 4F 3.688,6.177 4,6.375 0.313,0.198 10 false 4H 6.417,6.208 6.729,6.406 0.313,0.198 10 false 4L 5.406,6.219 5.719,6.417 0.313,0.198 10 false 4K
*1 Main Body ECU (Multiplex Network Body ECU) - -


*1: for LHD

*2: for RHD


a.

Remove the main body ECU (multiplex network body ECU) from the driver side junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Reconnect the driver side junction block assembly connectors.


c.

Measure the voltage and resistance according to the value(s) in the table below.

Tester Connection Terminal Description Condition Specified Condition
A-11 (GND1) - Body ground Ground Always Below 1 Ω
A-30 (ACC) - Body ground ACC power supply Ignition switch ACC 11 to 14 V
Ignition switch off Below 1 V
A-31 (BECU) - Body ground Auxiliary battery power supply Ignition switch off 11 to 14 V
A-32 (IG) - Body ground IG power supply Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V


d.

Install the main body ECU (multiplex network body ECU) to the driver side junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>INSTALLATION


e.

Measure the voltage and check for pulses according to the value(s) in the table below.

Tester Connection Terminal Description Condition Specified Condition
D11-1 (FLCY) - Body ground Front door courtesy light switch assembly LH input Front door LH open → closed Below 1 V → 4.7 to 5.3 V
D11-6 (FRCY) - Body ground Front door courtesy light switch assembly RH input Front door RH open → closed Below 1 V → 4.7 to 5.3 V
4H-26 (LCTY) - Body ground*1 Rear door courtesy light switch assembly LH input Rear door LH open → closed Below 1 V → 4.7 to 5.3 V
4A-42 (LCTY) - Body ground*2 Rear door courtesy light switch assembly LH input Rear door LH open → closed Below 1 V → 4.7 to 5.3 V
4D-19 (RCTY) - Body ground*1 Rear door courtesy light switch assembly RH input Rear door RH open → closed Below 1 V → 4.7 to 5.3 V
4H-26 (RCTY) - Body ground*2 Rear door courtesy light switch assembly RH input Rear door RH open → closed Below 1 V → 4.7 to 5.3 V
D14-18 (L2) - Body ground Driver and front passenger door key-linked lock input Driver or front passenger door key cylinder turned to neutral position → on (lock) Pulse generation → Below 1 V
D14-17 (UL3) - Body ground Driver door key-linked unlock input Driver door key cylinder turned to neutral position → on (unlock) Pulse generation → Below 1 V
4A-2 (ACT+) - Body ground Door lock motor lock drive output Door control switch or door key cylinder off → on (lock) Below 1 V → 11 to 14 V → Below 1 V
4H-18 (ACT+) - Body ground Door lock motor lock drive output Door control switch or door key cylinder off → on (lock) Below 1 V → 11 to 14 V → Below 1 V
4H-6 (ACT+) - Body ground Door lock motor lock drive output Door control switch or door key cylinder off → on (lock) Below 1 V → 11 to 14 V → Below 1 V
4A-1 (ACT-) - Body ground Front passenger door lock motor unlock drive output Door control switch front passenger door key cylinder off → on (unlock) Below 1 V → 11 to 14 V → Below 1 V
4H-7 (ACT-) - Body ground Front passenger door lock motor unlock drive output Door control switch front passenger door key cylinder off → on (unlock) Below 1 V → 11 to 14 V → Below 1 V
4H-8 (ACTD) - Body ground Driver door lock motor unlock drive output Door control switch or driver door key cylinder off → on (unlock) Below 1 V → 11 to 14 V → Below 1 V
4D-14 (LSFR) - Body ground*1 Front door RH unlock detection switch input Front door RH locked → unlocked Pulse generation → Below 1 V
4H-31 (LSFR) - Body ground*2 Front door RH unlock detection switch input Front door RH locked → unlocked Pulse generation → Below 1 V
4H-31 (LSFL) - Body ground*1 Front door LH unlock detection switch input Front door LH locked → unlocked Pulse generation → Below 1 V
4A-15 (LSFL) - Body ground*2 Front door LH unlock detection switch input Front door LH locked → unlocked Pulse generation → Below 1 V
D12-20 (LSWR) - Body ground Rear door RH unlock detection switch input Rear door RH locked → unlocked Pulse generation → Below 1 V
4H-21 (LSWL) - Body ground*1 Rear door LH unlock detection switch input Rear door LH locked → unlocked Pulse generation → Below 1 V
4D-12 (LSWL) - Body ground*2 Rear door LH unlock detection switch input Rear door LH locked → unlocked Pulse generation → Below 1 V
4A-46 (GSW) - Body ground Collision detection input Ignition switch ON 2.9 to 4.2 V



CHECK FRONT MULTIPLEX NETWORK DOOR ECU LH (w/ Double Locking System)


B340248E09
2.25,0.292 2.677,0.573 0.427,0.281 3.448,0.271 3.875,0.552 0.427,0.281 3.542,0.344 3.854,0.542 0.313,0.198 10 false E25 2.354,0.354 2.667,0.552 0.313,0.198 10 false E24

a.

Disconnect the E25 front multiplex network door ECU LH connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbols) Terminal Description Condition Specified Condition
E25-1 (GND) - Body ground Ground Always Below 1 Ω
E25-6 (BDR) - E25-1 (GND) Battery power supply Ignition switch off 11 to 14 V
E25-4 (CPUB) - E25-1 (GND) Battery power supply Ignition switch off 11 to 14 V


c.

Reconnect the E25 front multiplex network door ECU LH connector.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbols) Terminal Description Condition Specified Condition
E24-5 (A1+) - E25-1 (GND) Double lock motor drive output Wireless or entry operation performed to set double lock 11 to 14 V
Wireless or entry operation not performed Below 1 V
E24-6 (A1-) - E25-1 (GND) Double lock motor drive output Wireless or entry operation performed to unset double lock 11 to 14 V
Wireless or entry operation not performed Below 1 V
E24-24 (DBLS) - E24-4 (DBE) Double lock position switch signal input Double lock UNSET Pulse generation
Double lock SET Below 1 V



CHECK FRONT MULTIPLEX NETWORK DOOR ECU RH (w/ Double Locking System)


B340248E10
2.25,0.292 2.677,0.573 0.427,0.281 3.448,0.271 3.875,0.552 0.427,0.281 3.542,0.333 3.854,0.531 0.313,0.198 10 false E7 2.354,0.354 2.667,0.552 0.313,0.198 10 false E6

a.

Disconnect the E7 front multiplex network door ECU RH connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbols) Terminal Description Condition Specified Condition
E7-1 (GND) - Body ground Ground Always Below 1 Ω
E7-6 (BDR) - E7-1 (GND) Battery power supply Ignition switch off 11 to 14 V
E7-4 (CPUB) - E7-1 (GND) Battery power supply Ignition switch off 11 to 14 V


c.

Reconnect the E7 front multiplex network door ECU LH connector.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbols) Terminal Description Condition Specified Condition
E6-5 (A1+) - E7-1 (GND) Double lock motor drive output Wireless or entry operation performed to set double lock 11 to 14 V
Wireless or entry operation not performed Below 1 V
E6-6 (A1-) - E7-1 (GND) Double lock motor drive output Wireless or entry operation performed to unset double lock 11 to 14 V
Wireless or entry operation not performed Below 1 V
E6-24 (DBLS) - E6-4 (DBE) Double lock position switch signal input Double lock UNSET Pulse generation
Double lock SET Below 1 V



CHECK REAR MULTIPLEX NETWORK DOOR ECU LH (w/ Double Locking System)


B340249N16
2.875,0.167 3.323,0.448 0.448,0.281 4.073,0.188 4.521,0.469 0.448,0.281 4.188,0.271 4.5,0.469 0.313,0.198 10 false F16 2.99,0.25 3.302,0.448 0.313,0.198 10 false F15

a.

Disconnect the F16 rear multiplex network door ECU LH connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbols) Terminal Description Condition Specified Condition
F16-1 (GND) - Body ground Ground Always Below 1 Ω
F16-4 (BDR) - F16-1 (GND) Battery power supply Ignition switch off 11 to 14 V
F16-11 (CPUB) - F16-1 (GND) Battery power supply Ignition switch off 11 to 14 V


c.

Reconnect the F16 rear multiplex network door ECU LH connector.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbols) Terminal Description Condition Specified Condition
F15-5 (A1+) - F16-1 (GND) Double lock motor drive output Wireless or entry operation performed to set double lock 11 to 14 V
Wireless or entry operation not performed Below 1 V
F15-6 (A1-) - F16-1 (GND) Double lock motor drive output Wireless or entry operation performed to unset double lock 11 to 14 V
Wireless or entry operation not performed Below 1 V
F15-24 (DBLS) - F15-4 (DLE1) Double lock position switch signal input Double lock UNSET Pulse generation
Double lock SET Below 1 V



CHECK REAR MULTIPLEX NETWORK DOOR ECU RH (w/ Double Locking System)


B340249N17
2.875,0.167 3.323,0.448 0.448,0.281 4.073,0.188 4.521,0.469 0.448,0.281 4.229,0.281 4.542,0.479 0.313,0.198 10 false F5 3.052,0.271 3.365,0.469 0.313,0.198 10 false F4

a.

Disconnect the F5 rear multiplex network door ECU RH connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbols) Terminal Description Condition Specified Condition
F5-1 (GND) - Body ground Ground Always Below 1 Ω
F5-4 (BDR) - F5-1 (GND) Battery power supply Ignition switch off 11 to 14 V
F5-11 (CPUB) - F5-1 (GND) Battery power supply Ignition switch off 11 to 14 V


c.

Reconnect the F5 rear multiplex network door ECU RH connector.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbols) Terminal Description Condition Specified Condition
F4-5 (A1+) - F5-1 (GND) Double lock motor drive output Wireless or entry operation performed to set double lock 11 to 14 V
Wireless or entry operation not performed Below 1 V
F4-6 (A1-) - F5-1 (GND) Double lock motor drive output Wireless or entry operation performed to unset double lock 11 to 14 V
Wireless or entry operation not performed Below 1 V
F4-24 (DBLS) - F4-4 (DLE1) Double lock position switch signal input Double lock UNSET Pulse generation
Double lock SET Below 1 V