Home › Vehicle Interior › DOOR LOCK › POWER DOOR LOCK CONTROL SYSTEM
RM37H0E _58 Vehicle Interior _095313 DOOR LOCK _0452394 POWER DOOR LOCK CONTROL SYSTEM C

DOOR LOCK  POWER DOOR LOCK CONTROL SYSTEM  B1243  GSW Terminal Circuit Malfunction  


DESCRIPTION

If the collision door lock release function does not operate normally, or an open or short in the GSW input circuit of the main body ECU (multiplex network body ECU) is detected, DTC B1243 will be stored.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
B1243 GSW Terminal Circuit Malfunction A malfunction occurs in the GSW input circuit of the main body ECU (multiplex network body ECU).
·

Main body ECU (multiplex network body ECU)

·

Instrument panel junction block assembly

·

Airbag ECU assembly

·

Harness or connector


Main Body A

WIRING DIAGRAM

B345030E98
1.25,0.938 1.708,1.135 0.458,0.198 10 false GSW 1.667,0.833 1.979,1.031 0.313,0.198 10 false 25 0.583,1.802 1.042,2 0.458,0.198 10 false D10 0.594,1.969 2.198,2.271 1.604,0.302 10 false Airbag ECU Assembly 5.646,0.938 6.104,1.135 0.458,0.198 10 false GSW 4.365,0.823 4.677,1.021 0.313,0.198 10 false 46 5.406,0.823 5.719,1.021 0.313,0.198 10 false 24 4,1.292 4.313,1.49 0.313,0.198 10 false 4A 4.01,1.438 5.563,1.813 1.552,0.375 10 false Driver Side Junction Block Assembly 5.344,1.802 5.656,2 0.313,0.198 10 false A 5.344,1.979 7,2.531 1.656,0.552 10 false Main Body ECU (Multiplex Network Body ECU)

CAUTION / NOTICE / HINT

NOTICE:
·

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

If the main body ECU (multiplex network body ECU) is replaced, refer to the Service Bulletin.

·

When DTC B1243 is output, the collision door lock release, shift-linked automatic door lock/unlock and speed-sensitive automatic door lock functions are prohibited.

·

The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION



PROCEDURE

1.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Main Body > Clear DTCs
50002 123

Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Recheck for DTCs.

Body Electrical > Main Body > Trouble Codes
50001 123
OK:

DTC B1243 is not output.



Result:
Proceed to
OK
NG



OK

NG

3.CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
3.CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

Pre-procedure1

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 60 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.


NOTICE:

Turning the ignition switch ON with the airbag ECU assembly connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.



b.

Disconnect the airbag ECU assembly connector.

HINT:

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION



c.

Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.


Procedure1

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(D10)Location & Routing

Click Connector(D10)Instrument Panel>Instrument Panel Wire>Airbag ECU Assembly

D10-25 (GSW) - Body ground Ignition switch to ON 4.3 to 5.5 V



Result:
Proceed to
OK
NG


Post-procedure1

a.

None



OK

NG

4.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - AIRBAG ECU ASSEMBLY)
4.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - AIRBAG ECU ASSEMBLY)

Pre-procedure1

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 60 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



b.

Disconnect the 4A driver side junction block assembly connector.


c.

Disconnect the D10 airbag ECU assembly connector.

HINT:

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION



Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D10)Location & Routing

Click Connector(D10)Instrument Panel>Instrument Panel Wire>Airbag ECU Assembly

4A-46 - D10-25 (GSW) Always Below 1 Ω
4A-46 or D10-25 (GSW) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

a.

None



OK

5.INSPECT DRIVER SIDE JUNCTION BLOCK ASSEMBLY

NG

REPLACE HARNESS OR CONNECTOR

5.INSPECT DRIVER SIDE JUNCTION BLOCK ASSEMBLY

Pre-procedure1

a.

Remove the driver side junction block assembly.

HINT:

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL



b.

Remove the main body ECU (multiplex network body ECU) from the driver side junction block assembly.

HINT:

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL



Procedure1

a.

Measure the resistance according to the value(s) in the table below.

B472615C13
1.771,0.625 2.271,0.917 0.5,0.292 5.354,0.625 5.854,0.917 0.5,0.292 2.375,2.125 2.51,2.125 2.51,2.125 2.969,1.573 false 5.51,0.698 5.75,0.896 0.24,0.198 10 false 4A 2.01,0.708 2.167,0.906 0.156,0.198 10 false A 2.01,2.042 2.469,2.292 0.458,0.25 10 false GSW 0.115,0.052 0.427,0.25 0.313,0.198 10 false *a
*a Component without harness connected
(Driver Side Junction Block Assembly)
- -


Standard Resistance:
Tester Connection Condition Specified Condition
A-24 (GSW) - 4A-46 Always Below 1 Ω



Result:
Proceed to
OK
NG


Post-procedure1

a.

None



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE DRIVER SIDE JUNCTION BLOCK ASSEMBLY