In some cases, wireless door lock control functions are normal but the hazard warning light and/or wireless door lock buzzer answer-back function does not operate. In such cases, hazard warning light and wireless door lock buzzer signal output from the main body ECU (multiplex network body ECU) may be malfunctioning.
Before performing the inspection, check that DTC B1242 (wireless door lock control) is not output.
If the main body ECU (multiplex network body ECU) is replaced, refer to the Service Bulletin.
Select the setting by referring to the table below.
| Tester Display | Description | Default | Setting | ECU |
|---|---|---|---|---|
| Hazard Answer Back | When the doors are locked by wireless operation, the hazard warning lights flash once.
When the doors are unlocked by wireless operation, the hazard warning lights flash twice. |
ON | 0:OFF,1:ON | Main body ECU (Multiplex network body ECU) |
| Wireless Buzzer Resp | Wireless door lock buzzer response* | ON | 0:OFF,1:ON | Main body ECU (Multiplex network body ECU) |
| Wireless Buzzer Vol | Wireless door lock buzzer volume* | Level5 | 0000:Level7,0001:Level6,0010:Level5,0011:Level4,0100:Level3,0101:Level2,0110:Level1,0111:Level0 | Main body ECU (Multiplex network body ECU) |
*: w/ Wireless Door Lock Buzzer Answer-back Function
| Result | Proceed to |
|---|---|
| Both items are ON and except Level 0 | A |
| Either item is OFF or Level 0 | B |
A
B
Check the wireless door lock control function using the electrical key transmitter sub-assembly.
Click hereVehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM>OPERATION CHECK
| Result | Proceed to |
|---|---|
| Wireless door lock/unlock operates properly. | A |
| Wireless door lock/unlock does not operate properly. | B |
A
B
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| FR Door Lock Pos | Front door RH unlock detection switch signal | LOCK or UNLOCK | LOCK: Front door RH locked
UNLOCK: Front door RH unlocked |
- |
| FL Door Lock Pos | Front door LH unlock detection switch signal | LOCK or UNLOCK | LOCK: Front door LH locked
UNLOCK: Front door LH unlocked |
- |
| RR-Door Lock Pos SW | Rear door RH unlock detection switch signal | OFF or ON | OFF: Rear door RH locked
ON: Rear door RH unlocked |
- |
| RL-Door Lock Pos SW | Rear door LH unlock detection switch signal | OFF or ON | OFF: Rear door LH locked
ON: Rear door LH unlocked |
- |
| Tester Display |
|---|
| FR Door Lock Pos |
| FL Door Lock Pos |
| RR-Door Lock Pos SW |
| RL-Door Lock Pos SW |
The GTS display changes correctly in response to the lock/unlock operation.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the wireless answer-back operation using the electrical key transmitter sub-assembly.
Click hereVehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM>OPERATION CHECK
| Result | Proceed to |
|---|---|
| Only wireless door lock buzzer answer-back does not occur. | A |
| Only hazard warning light answer-back does not occur. | B |
A
B
Perform Active Test according to the display on the GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Wireless Buzzer | Wireless door lock buzzer | OFF/ON | - |
| Tester Display |
|---|
| Wireless Buzzer |
| Result | Proceed to |
|---|---|
| Wireless buzzer does not sound | A |
| Wireless buzzer sounds | B |
A
B
Disconnect the wireless door lock buzzer connector.
Perform the Active Test using the GTS and sound the wireless door lock buzzer.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Wireless Buzzer | Wireless door lock buzzer | OFF/ON | - |
| Tester Display |
|---|
| Wireless Buzzer |
| *a | Front view of wire harness connector
(to Wireless Door Lock Buzzer) |
While performing the Active Test, measure the voltage between the terminals of the wireless door lock buzzer.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A7)Location & Routingewd_type=routing;type=c;code=A7 |
||
| A7-1 (B) - A7-2 (E) | Active Test Wireless Buzzer ON | Pulse generation
(frequency: 2 kHz, high voltage: 11 to 14 V, low voltage: below 1 V) |
| Active Test Wireless Buzzer OFF | Below 1 V | |
| Proceed to |
|---|
| OK |
| NG |
OK
for LHD:
Click hereVehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK BUZZER (for LHD)>REMOVAL
for RHD:
Click hereVehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK BUZZER (for RHD)>REMOVAL
NG
Disconnect the wireless door lock buzzer connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A7)Location & Routingewd_type=routing;type=c;code=A7 |
||
| A7-2 (E) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the A7 wireless door lock buzzer connector.
Remove the main body ECU (multiplex network body ECU) from the driver side junction block assembly.
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL
Reconnect the 4F driver side junction block assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A7)Location & Routingewd_type=routing;type=c;code=A7 |
||
| A7-1 (B) - A-21 (BZR) | Always | Below 1 Ω |
| A7-1 (B) or A-21 (BZR) - Other terminals and body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the 4F driver side junction block assembly connector.
Disconnect the A7 wireless door lock buzzer connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A7)Location & Routingewd_type=routing;type=c;code=A7 |
||
| A7-1 (B) - 4F-31 | Always | Below 1 Ω |
| A7-1 (B) or 4F-31 - Other terminals and body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check that the hazard warning lights blink when the hazard warning signal switch is pressed.
Hazard warning lights blink.
| Proceed to |
|---|
| OK |
| NG |
OK
NG