The main body ECU (multiplex network body ECU) and rain sensor communicate via LIN communication. The main body ECU (multiplex network body ECU) stores this DTC if communication becomes abnormal.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Memory | DTC Output from | Priority |
|---|---|---|---|---|---|---|
| B1279 | Lost Communication with Humidity/Rain Sensor LIN | DTC Detection Condition:
Ignition switch ON (IG+ voltage 9.5 V or higher) Malfunction Status:
Communication malfunction with rain sensor Malfunction Duration:
Continues for 10 seconds or more |
·
Rain sensor ·
Harness or connector ·
Map light assembly |
○ | Main Body | B |
Inspect fuses for circuits related to this system before performing the following inspection procedure.
Pre-procedure1
None.
Procedure1
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
Post-procedure1
Turn the ignition switch to ON and wait for at least 10 seconds.
NEXT
Check for DTCs.
| Result | Proceed to |
|---|---|
| B1279 is not output | A |
| Only B1279 is output | B |
| B1279 and B1373 are output | C |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
C
Pre-procedure1
Disconnect the D12 main body ECU (multiplex network body ECU) connector.
Disconnect the H21 rain sensor connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(D12,H21)Location & Routingewd_type=routing;type=c,c;code=D12,H21 Click Connector(D12)Instrument Panel>Instrument Panel Wire>Main Body ECUewd_type=component;type=c;code=D12;pinno=3 Click Connector(H21)Body>No. 1 Roof Wire>Rain Sensorewd_type=component;type=c;code=H21;pinno=3 |
||
| D12-3 (LIN3) - H21-3 (MPX) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None.
OK
NG
Pre-procedure1
Disconnect the H21 rain sensor connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H21)Location & Routingewd_type=routing;type=c;code=H21 Click Connector(H21)Body>No. 1 Roof Wire>Rain Sensorewd_type=component;type=c;code=H21;pinno=4 |
||
| H21-4 (SIG) - Body ground | Always | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H21)Location & Routingewd_type=routing;type=c;code=H21 Click Connector(H21)Body>No. 1 Roof Wire>Rain Sensorewd_type=component;type=c;code=H21;pinno=2 |
||
| H21-2 (ES) - Body ground | Ignition switch off | Below 1 V |
| H21-2 (ES) - Body ground | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None.
OK
NG
Pre-procedure1
Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL
Remove the map light assembly.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A-1 (IG) - A-21 (IG2) | Always | Below 1 Ω |
| A-19 (GND) - A-14 (GND2) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG