Home › Vehicle Exterior › WIPER / WASHER › WIPER AND WASHER SYSTEM
RM37H0E _59 Vehicle Exterior _095212 WIPER / WASHER _0447384 WIPER AND WASHER SYSTEM C

WIPER / WASHER  WIPER AND WASHER SYSTEM  B1372  Wiper Switch Signal Mismatch between LIN and Line  


DESCRIPTION

Under normal operation, the windshield wiper motor assembly receives operation signals from the windshield wiper switch assembly via LIN communication.

The windshield wiper motor assembly and windshield wiper switch assembly are also connected via direct line in order to operate the front wipers in HI in an emergency. If the operation signals sent via LIN communication and direct line do not match, this DTC is stored.

DTC No. Detection Item DTC Detection Condition Trouble Area Memory DTC Output from Priority
B1372 Wiper Switch Signal Mismatch between LIN and Line
DTC Detection Condition:

Ignition switch ON (IG+ voltage 9.5 V or higher)


Malfunction Condition:

LIN communication and direct line input signals do not match


Malfunction Duration:

Malfunction determined if the status continues for 10 seconds or more


·

Windshield wiper motor assembly

·

Steering sensor

·

Harness or connector


○ Wiper A

WIRING DIAGRAM

for Wiper Switch LH Side Type:


E458772E01
0.885,7.094 1.979,7.323 1.094,0.229 10 false Steering Sensor 0.563,8.115 2.292,8.333 1.729,0.219 10 false : CAN Communication Line 0.563,8.469 2.292,8.688 1.729,0.219 10 false : LIN Communication Line 4.854,7.052 5.313,7.25 0.458,0.198 10 false A37 4.854,7.229 7.042,7.469 2.188,0.24 10 false Windshield Wiper Motor Assembly 2.75,6.646 3.208,6.844 0.458,0.198 10 false D34 2.833,6.438 2.99,6.635 0.156,0.198 10 false 2 4.906,6.625 5.219,6.823 0.313,0.198 10 false 2S 4.688,6.531 4.844,6.729 0.156,0.198 10 false 2 4.896,6.156 5.354,6.354 0.458,0.198 10 false LIN 4.677,6 4.833,6.198 0.156,0.198 10 false 6 5.135,5.135 6.781,5.542 1.646,0.406 10 false Main Body ECU (Multiplex Network Body ECU) 4.896,4.542 5.354,4.74 0.458,0.198 10 false LIN3 4.688,4.396 4.844,4.594 0.156,0.198 10 false 3 5.135,4.958 5.594,5.156 0.458,0.198 10 false D12 0.542,3.448 0.854,3.646 0.313,0.198 10 false IC 3.063,3.188 4.49,3.563 1.427,0.375 10 false Steering Wheel Switch Housing 4.885,3.177 7.094,3.385 2.208,0.208 10 false Windshield Wiper Switch Assembly 2.813,2.594 3.125,2.792 0.313,0.198 10 false z2 2.813,2.396 3.125,2.594 0.313,0.198 10 false 33 2.813,1.802 3.125,2 0.313,0.198 10 false 27 2.802,2.01 3.115,2.208 0.313,0.198 10 false z2 2.438,1.885 2.75,2.083 0.313,0.198 10 false +2 3.146,1.896 3.458,2.094 0.313,0.198 10 false +2 4.906,1.906 5.219,2.104 0.313,0.198 10 false +2 2.5,2.469 2.656,2.667 0.156,0.198 10 false E 3.156,2.5 3.313,2.698 0.156,0.198 10 false E 4.917,2.479 5.073,2.677 0.156,0.198 10 false E 4.552,2.594 4.865,2.792 0.313,0.198 10 false z4 4.552,2.01 4.865,2.208 0.313,0.198 10 false z4 4.552,1.792 4.865,1.99 0.313,0.198 10 false 13 4.583,2.385 4.896,2.583 0.313,0.198 10 false 4 5.552,0.625 6.438,0.844 0.885,0.219 10 false Wiper Switch 5.271,1.396 5.583,1.594 0.313,0.198 10 false HI 5.844,1.073 6.156,1.271 0.313,0.198 10 false +2 6.542,1.073 6.854,1.271 0.313,0.198 10 false E 2.125,0.583 2.583,0.781 0.458,0.198 10 false 5 V 2.417,6.521 2.729,6.719 0.313,0.198 10 false 2S


for Wiper Switch RH Side Type:


E458772E02
0.885,7.052 1.979,7.281 1.094,0.229 10 false Steering Sensor 0.563,8.115 2.292,8.333 1.729,0.219 10 false : CAN Communication Line 0.563,8.469 2.292,8.688 1.729,0.219 10 false : LIN Communication Line 4.854,7.052 5.313,7.25 0.458,0.198 10 false A37 4.854,7.229 7.042,7.469 2.188,0.24 10 false Windshield Wiper Motor Assembly 2.75,6.646 3.208,6.844 0.458,0.198 10 false D34 2.833,6.438 2.99,6.635 0.156,0.198 10 false 2 4.906,6.625 5.219,6.823 0.313,0.198 10 false 2S 4.25,6.531 4.823,6.729 0.573,0.198 10 false 3*1, 2*2 4.896,6.156 5.354,6.354 0.458,0.198 10 false LIN 4.26,6 4.833,6.219 0.573,0.219 10 false 7*1, 6*2 5.135,5.125 6.781,5.531 1.646,0.406 10 false Main Body ECU (Multiplex Network Body ECU) 4.896,4.542 5.354,4.74 0.458,0.198 10 false LIN3 4.688,4.385 4.844,4.583 0.156,0.198 10 false 3 5.135,4.948 5.594,5.146 0.458,0.198 10 false D12 0.542,3.448 0.854,3.646 0.313,0.198 10 false IC 3.063,3.198 4.49,3.573 1.427,0.375 10 false Steering Wheel Switch Housing 4.885,3.167 7.083,3.365 2.198,0.198 10 false Windshield Wiper Switch Assembly 2.802,2.594 3.115,2.792 0.313,0.198 10 false z2 2.813,2.375 3.125,2.573 0.313,0.198 10 false 33 2.813,1.802 3.125,2 0.313,0.198 10 false 27 2.802,2.01 3.115,2.208 0.313,0.198 10 false z2 2.438,1.896 2.75,2.094 0.313,0.198 10 false +2 3.146,1.885 3.458,2.083 0.313,0.198 10 false +2 4.906,1.906 5.219,2.104 0.313,0.198 10 false +2 2.49,2.479 2.646,2.677 0.156,0.198 10 false E 3.156,2.469 3.313,2.667 0.156,0.198 10 false E 4.917,2.49 5.073,2.688 0.156,0.198 10 false E 4.563,2.594 4.875,2.792 0.313,0.198 10 false z4 4.563,2.021 4.875,2.219 0.313,0.198 10 false z4 4.552,1.813 4.865,2.01 0.313,0.198 10 false 12 4.594,2.396 4.906,2.594 0.313,0.198 10 false 5 5.552,0.625 6.438,0.844 0.885,0.219 10 false Wiper Switch 5.281,1.406 5.594,1.604 0.313,0.198 10 false HI 5.854,1.073 6.167,1.271 0.313,0.198 10 false +2 6.521,1.073 6.833,1.271 0.313,0.198 10 false E 0.146,7.448 1.833,7.646 1.688,0.198 10 false *1: for LHD 0.146,7.74 1.833,7.938 1.688,0.198 10 false *2: for RHD 2.125,0.573 2.583,0.771 0.458,0.198 10 false 5 V 2.427,6.51 2.74,6.708 0.313,0.198 10 false 2S


CAUTION / NOTICE / HINT

NOTICE:

First perform the communication function inspections in How to Proceed with Troubleshooting to confirm that there are no CAN communication malfunctions before troubleshooting this problem.

Click hereVehicle Exterior>WIPER / WASHER>WIPER AND WASHER SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING


PROCEDURE

1.CLEAR THE DTC

Pre-procedure1

a.

None.


Procedure1

a.

Clear the DTCs.

Body Electrical > Wiper > Clear DTCs
50002 384

Result:
Proceed to
NEXT


Post-procedure1

a.

Turn the ignition switch to ON and wait for at least 10 seconds.



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Check for DTC.

Body Electrical > Wiper > Trouble Codes
50001 384

Result:
Result Proceed to
B1372 is not output A
B1372 is output B



A

B

3.READ VALUE USING GTS
3.READ VALUE USING GTS
a.

Read the Data List according to the display on the GTS.

Body Electrical > Wiper > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Wiper Switch HI (Line) Windshield wiper switch assembly HI signal (abnormal control system) input condition OFF or ON OFF: Windshield wiper switch assembly not in HI position
ON: Windshield wiper switch assembly in HI position
-
Chassis > Steering Angle Sensor > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Wiper Hi Switch Windshield wiper switch assembly (HI position) condition OFF or ON OFF: Windshield wiper switch assembly not in HI position
ON: Windshield wiper switch assembly in HI position
-
Body Electrical > Wiper > Data List
Tester Display
Wiper Switch HI (Line)
50003 384 20
Chassis > Steering Angle Sensor > Data List
Tester Display
Wiper Hi Switch
50003 445 18

Result:
Result Proceed to
Only "Wiper Switch HI (Line)" changes normally A
Only "Wiper Hi Switch" changes normally B



A

B

4.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER MOTOR ASSEMBLY HI SIGNAL INPUT)
4.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER MOTOR ASSEMBLY HI SIGNAL INPUT)

Pre-procedure1

a.

Disconnect the A37 windshield wiper motor assembly connector.


Procedure1

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for LHD
Tester Connection Condition Specified Condition

Click Location & Routing(A37)Location & Routing

Click Connector(A37)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Windshield Wiper Motor Assembly

A37-3 (2S) - Body ground Ignition switch to ON , HI operating Below 1 V
A37-3 (2S) - Body ground Windshield wiper motor assembly stopped 11 to 14 V

for RHD
Tester Connection Condition Specified Condition

Click Location & Routing(A37)Location & Routing

Click Connector(A37)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Windshield Wiper Motor Assembly

A37-2 (2S) - Body ground Ignition switch to ON , HI operating Below 1 V
A37-2 (2S) - Body ground Windshield wiper motor assembly stopped 11 to 14 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None.



OK

REPLACE WINDSHIELD WIPER MOTOR ASSEMBLY

NG

5.CHECK HARNESS AND CONNECTOR (STEERING SENSOR - WINDSHIELD WIPER MOTOR ASSEMBLY)
5.CHECK HARNESS AND CONNECTOR (STEERING SENSOR - WINDSHIELD WIPER MOTOR ASSEMBLY)

Pre-procedure1

a.

Disconnect the D34 steering sensor connector.


b.

Disconnect the A37 windshield wiper motor assembly connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition

Click Location & Routing(D34,A37)Location & Routing

Click Connector(D34)Instrument Panel>Instrument Panel Wire>Steering Sensor

Click Connector(A37)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Windshield Wiper Motor Assembly

D34-2 (2S) - A37-3 (2S) Always Below 1 Ω
D34-2 (2S) or A37-3 (2S) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition

Click Location & Routing(D34,A37)Location & Routing

Click Connector(D34)Instrument Panel>Instrument Panel Wire>Steering Sensor

Click Connector(A37)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Windshield Wiper Motor Assembly

D34-2 (2S) - A37-2 (2S) Always Below 1 Ω
D34-2 (2S) or A37-2 (2S) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR