When the windshield washer motor and pump assembly receives signals from the windshield wiper switch assembly (washer switch) it operates to spray washer fluid from the washer nozzle sub-assemblies.
Inspect fuses for circuits related to this system before performing the following inspection procedure.
Perform the Active Test according to the display on the GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Front Washer | Operates the open side washer | OFF or ON | - |
| Rear Washer | Operates the closed side washer | OFF or ON | - |
| Tester Display |
|---|
| Front Washer |
| Tester Display |
|---|
| Rear Washer |
Washer fluid sprays from each washer nozzle.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
OK
NG
Disconnect the A10 windshield washer motor and pump assembly connector.
Disconnect the A37 windshield wiper motor assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A10,A37)Location & Routingewd_type=routing;type=c,c;code=A10,A37 |
||
| A10-1 (B) - A37-1 (WSR+) | Always | Below 1 Ω |
| A10-2 (SW) - A37-2 (WSR-) | Always | Below 1 Ω |
| A10-1 (B) or A37-1 (WSR+) - Body ground | Always | 10 kΩ or higher |
| A10-2 (SW) or A37-2 (WSR-) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A10,A37)Location & Routingewd_type=routing;type=c,c;code=A10,A37 |
||
| A10-1 (B) - A37-4 (WSR+) | Always | Below 1 Ω |
| A10-2 (SW) - A37-3 (WSR-) | Always | Below 1 Ω |
| A10-1 (B) or A37-4 (WSR+) - Body ground | Always | 10 kΩ or higher |
| A10-2 (SW) or A37-3 (WSR-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the A37 windshield wiper motor assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A37)Location & Routingewd_type=routing;type=c;code=A37 |
||
| A37-4 (GND) - Body ground | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A37)Location & Routingewd_type=routing;type=c;code=A37 |
||
| A37-1 (GND) - Body ground | Always | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A37)Location & Routingewd_type=routing;type=c;code=A37 |
||
| A37-5 (FWAB) - Body ground | Ignition switch off | 11 to 14 V |
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A37)Location & Routingewd_type=routing;type=c;code=A37 |
||
| A37-8 (FWAB) - Body ground | Ignition switch off | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG