Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › STEERING ANGLE SENSOR
RM37H0E _54 Brake _096746 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0454015 STEERING ANGLE SENSOR A

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  STEERING ANGLE SENSOR  INSTALLATION  


CAUTION / NOTICE / HINT

COMPONENTS (INSTALLATION)
C446182N02
1,0.5 6.25,3.25 5.25,2.75 2.271,2.292 2.271,2.542 2.271,2.542 2.604,2.542 false 6.25,2 6.5,2 false 3.948,1.417 4.281,1.417 false 6.625,0.167 6.875,0.167 false 6.625,0.583 6.792,0.583 false 2.979,2.427 3.313,2.76 0.333,0.333 18 false 2 6.552,1.854 6.885,2.188 0.333,0.333 18 false 3 6.438,0.021 6.688,0.354 0.25,0.333 18 false 1 6.438,0.438 6.771,0.771 0.333,0.333 18 false 4 3.781,1.365 4.115,1.698 0.333,0.333 10 false *1

Procedure Part Name Code
Z101186

Z101188

Z101187

1 INSPECT SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY 84306 (Click here) - -
2 STEERING SENSOR 89245B (Click here) - -
3 INSTALL SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY - - - -
4 UPDATE ECU SECURITY KEY - - - (Click here)

*1 SPIRAL CABLE SUB-ASSEMBLY - -

CAUTION / NOTICE / HINT

NOTICE:
·

A lock pin is installed to a new steering sensor. Do not remove the lock pin before the steering sensor is installed to the spiral cable sub-assembly.

·

After performing the update ECU security key procedure, make sure to perform the initialization procedure for when the cable has been disconnected and reconnected to the negative (-) battery terminal.



PROCEDURE

Hide 1.INSPECT SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY

Hide 89245B 2.INSTALL STEERING SENSOR

a.
C436427C03
2.719,1.198 2.24,1.698 2.24,1.698 2.719,0.708 true 3.208,0.927 3.771,0.927 true 1.438,0.76 1.594,1.188 true 2.708,0.479 2.917,0.25 2.917,0.25 3.667,0.25 true 0.646,0.198 0.927,0.552 0.281,0.354 18 false i 4.698,0.917 4.979,1.271 0.281,0.354 18 false ii 2.125,1.708 2.302,1.917 0.177,0.208 10 true *a 3.802,0.844 4.021,1.031 0.219,0.188 10 true *b 1.531,1.208 1.708,1.406 0.177,0.198 10 true *b 3.698,0.167 3.917,0.354 0.219,0.188 10 true *c
*a Guide *b Pin
*c Lock Pin - -


i.

Align the 2 pins and 2 guides, and engage the 6 claws to install the steering sensor to the spiral cable sub-assembly.

NOTICE:
·

Do not remove the lock pin before the steering sensor is installed to the spiral cable sub-assembly.

·

Do not damage the claws or pins of the spiral cable sub-assembly or guides of the steering sensor.

·

The spiral cable sub-assembly can be rotated up to 30° even when the interlock is engaged. Therefore, make sure that both guides are aligned properly when installing the steering sensor to the spiral cable sub-assembly.




ii.

Remove the lock pin from the steering sensor.



Hide 3.INSTALL SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY