Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › BRAKE PEDAL STROKE SENSOR (for RHD) › 2020.11–2021.08
RM37H0E _54 Brake _096746 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0454017 BRAKE PEDAL STROKE SENSOR(for RHD) A

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  BRAKE PEDAL STROKE SENSOR(for RHD)  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
C448766N02
6.333,0.25 6.75,0.25 false 6.333,0.667 6.75,0.667 false 3.333,1.167 3.333,1.417 3.333,1.417 3.583,1.417 false 6.177,0.115 6.594,0.531 0.417,0.417 18 false 1 6.177,0.531 6.51,0.865 0.333,0.333 18 false 2 3.646,1.292 3.896,1.625 0.25,0.333 18 false 3

Procedure Part Name Code
Z101186

Z101188

Z101187

1 PRECAUTION - (Click here) - -
2 DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL - (Click here) - -
3 LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY 73900 - - -

C448765N02
2.75,2.615 3,2.615 false 2.104,2.406 2.438,2.656 0.333,0.25 10 false x 2 3.375,2.479 3.958,2.896 0.583,0.417 18 false 4

Procedure Part Name Code
Z101186

Z101188

Z101187

4 BRAKE PEDAL STROKE SENSOR ASSEMBLY 89510D (Click here) - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during brake pedal stroke sensor assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*: Even when not replacing the part, it is necessary to perform the specified necessary procedures after installation.

Disconnect cable from negative (-) auxiliary battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)
Brake pedal stroke sensor assembly* Perform "Calibration"
·

DTCs are stored

·

ABS warning light illuminates

·

Brake system warning light (yellow indicator) illuminates

·

Slip indicator light illuminates

·

Electronically controlled brake system disabled or malfunctions


(Click here)
Brake pedal stroke sensor assembly adjustment Electronically controlled brake system malfunctions

HINT:

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Adaptive high beam system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Air conditioning system After the ignition switch is turned to ON, theservo motor and expansion valve standardposition is recognized. -



PROCEDURE

Hide 1. PRECAUTION

Z101186

CAUTION:
B475753

Be sure to read precaution thoroughly before servicing.

Click here(Click here)


NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click here(Click here)



Hide 2.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

Z101186

CAUTION:
B422343

·

Wait at least 60 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.




Click hereGeneral>MAINTENANCE>AUXILIARY BATTERY>REMOVAL

Hide 73900 3.REMOVE LOWER NO. 1 INSTRUMENT PANEL AIR BAG ASSEMBLY

Hide 89510D 4.REMOVE BRAKE PEDAL STROKE SENSOR ASSEMBLY

a.
C447597N01
3.229,1.49 3.448,1.771 0.219,0.281 18 true i 2.396,0.396 2.563,0.729 0.167,0.333 18 false ii 2.469,1.313 2.635,1.646 0.167,0.333 18 false ii

i.

Disconnect the connector from the brake pedal stroke sensor assembly.


ii.

Remove the 2 nuts and brake pedal stroke sensor assembly from the brake pedal support assembly.

NOTICE:
·

Do not drop the brake pedal stroke sensor assembly.

·

If the brake pedal stroke sensor assembly has been dropped, replace the brake pedal stroke sensor assembly with a new one.