Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE SYSTEM
RM37H0E _54 Brake _096747 BRAKE SYSTEM (OTHER) _0454020 BRAKE SYSTEM G

BRAKE SYSTEM (OTHER)  BRAKE SYSTEM  ON-VEHICLE INSPECTION  


CAUTION / NOTICE / HINT

NOTICE:

DTCs may be stored during the inspection procedure. Be sure to clear the DTCs and check that no DTCs are output after the inspection is finished.


PROCEDURE

Hide 1.INSPECT PRESSURE SENSOR

a.

Check the auxiliary battery voltage.

Standard Voltage:

11 to 14 V (while the ignition switch is off)



b.

Set a pedal effort gauge and SST.

HINT:

Simultaneously measure the brake fluid pressure of all 4 wheels, or 2 wheels at a time.


i.
C452873C01
1.917,0.583 2.167,0.583 false 2.542,0.333 2.792,0.333 false 0.646,0.333 0.896,0.333 false 0.281,3.052 0.448,3.052 false 2.917,3.063 3.083,3.063 3.083,3.063 3.083,2.979 false 2.208,0.521 2.458,0.688 0.25,0.167 10 false *a 2.365,0.271 2.615,0.521 0.25,0.25 10 false *b 0.49,2.99 0.823,3.24 0.333,0.25 10 false *c 0.948,0.271 1.198,0.521 0.25,0.25 10 false *b 2.75,3 3,3.167 0.25,0.167 10 false *c
*a Pedal Effort Gauge
*b SST (LSPV Gauge)
*c SST (No. 1 Nipple)


Set a pedal effort gauge and SST.

SST
09709-29018  (09709-00060)


ii.

Move the shift lever to P and apply the parking brake.


iii.

Bleed air from SST (LSPV gauge).

Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE FLUID>BLEEDING



c.

Inspect the master cylinder sensor 1, reaction force pressure and servo pressure.

i.

Check the value output from "Master Cylinder Sensor 1", "Reaction Force Pressure" and "Servo Pressure" by depressing the brake pedal.

Chassis > Brake/EPB > Data List
Tester Display
Master Cylinder Sensor 1
50003 435 21
Chassis > Brake Booster > Data List
Tester Display
Reaction Force Pressure
Servo Pressure
50003 466 205,210
Standard Result:
Pedal Effort Reaction Force Pressure
(MPa)
Servo Pressure
(MPa)
Master Cylinder Sensor 1
(MPa)
Front Left Wheel Hydraulic Pressure Front Right Wheel Hydraulic Pressure
50 N (5 kgf, 11.2 lbf) 0 to 0.64 0.81 to 4.81 0.51 to 4.51 0.51 to 4.51 MPa (5.2 to 45.9 kgf/cm2, 74 to 653 psi) 0.51 to 4.51 MPa (5.2 to 45.9 kgf/cm2, 74 to 653 psi)
100 N (10 kgf, 22.5 lbf) 0.52 to 1.32 4.32 to 8.32 4.02 to 8.02 4.02 to 8.02 MPa (41.0 to 81.7 kgf/cm2, 583 to 1162 psi) 4.02 to 8.02 MPa (41.0 to 81.7 kgf/cm2, 583 to 1162 psi)
150 N (15 kgf, 33.7 lbf) 1.17 to 1.97 7.30 to 11.3 7.00 to 11.00 7.00 to 11.00 MPa (71.4 to 112.1 kgf/cm2, 1015 to 1595 psi) 7.00 to 11.00 MPa (71.4 to 112.1 kgf/cm2, 1015 to 1595 psi)
200 N (20 kgf, 45.0 lbf) 1.85 to 2.65 7.30 to 11.3 7.00 to 11.00 7.00 to 11.00 MPa (71.4 to 112.1 kgf/cm2, 1015 to 1595 psi) 7.00 to 11.00 MPa (71.4 to 112.1 kgf/cm2, 1015 to 1595 psi)


Standard Result:
Pedal Effort Reaction Force Pressure
(MPa)
Servo Pressure
(MPa)
Master Cylinder Sensor 1
(MPa)
Rear Left Wheel Hydraulic Pressure Rear Right Wheel Hydraulic Pressure
50 N (5 kgf, 11.2 lbf) 0 to 0.64 0.81 to 4.81 0.51 to 4.51 0.51 to 4.51 MPa (5.2 to 45.9 kgf/cm2, 74 to 653 psi) 0.51 to 4.51 MPa (5.2 to 45.9 kgf/cm2, 74 to 653 psi)
100 N (10 kgf, 22.5 lbf) 0.52 to 1.32 4.32 to 8.32 4.02 to 8.02 4.02 to 8.02 MPa (41.0 to 81.7 kgf/cm2, 583 to 1162 psi) 4.02 to 8.02 MPa (41.0 to 81.7 kgf/cm2, 583 to 1162 psi)
150 N (15 kgf, 33.7 lbf) 1.17 to 1.97 7.30 to 11.3 7.00 to 11.00 7.00 to 11.00 MPa (71.4 to 112.1 kgf/cm2, 1015 to 1595 psi) 7.00 to 11.00 MPa (71.4 to 112.1 kgf/cm2, 1015 to 1595 psi)
200 N (20 kgf, 45.0 lbf) 1.85 to 2.65 7.30 to 11.3 7.00 to 11.00 7.00 to 11.00 MPa (71.4 to 112.1 kgf/cm2, 1015 to 1595 psi) 7.00 to 11.00 MPa (71.4 to 112.1 kgf/cm2, 1015 to 1595 psi)




d.

Remove the pedal effort gauge and SST.

i.

Remove the pedal effort gauge and SST, and bleed the brake line.

Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE FLUID>BLEEDING



e.

Inspect the accumulator pressure.

i.

While fully depressing the brake pedal 4 or 5 times, check that the "ECB Motor Relay" changes to ON once or more.

Chassis > Brake Booster > Data List
Tester Display
ECB Motor Relay
Accumulator Pressure
50003 466 96,212
HINT:

Usually the "ECB Motor Relay" is OFF.



ii.

After confirming that the brake booster pump motor stops, check the value output from "Accumulator Pressure".

Standard Result:

15 to 21 MPa




Hide 47210L 2.INSPECT BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

a.

Check the auxiliary battery voltage.

Standard Voltage:

11 to 14 V (while the ignition switch is off)



b.

Set a pedal effort gauge and SST.

HINT:

Simultaneously measure the brake fluid pressure of all 4 wheels, or 2 wheels at a time.


i.
C452873C01
1.917,0.583 2.167,0.583 false 2.542,0.333 2.792,0.333 false 0.646,0.333 0.896,0.333 false 0.281,3.052 0.448,3.052 false 2.917,3.063 3.083,3.063 3.083,3.063 3.083,2.979 false 2.208,0.521 2.458,0.688 0.25,0.167 10 false *a 2.365,0.271 2.615,0.521 0.25,0.25 10 false *b 0.49,2.99 0.823,3.24 0.333,0.25 10 false *c 0.948,0.271 1.198,0.521 0.25,0.25 10 false *b 2.75,3 3,3.167 0.25,0.167 10 false *c
*a Pedal Effort Gauge
*b SST (LSPV Gauge)
*c SST (No. 1 Nipple)


Set a pedal effort gauge and SST.

SST
09709-29018  (09709-00060)


ii.

Move the shift lever to P and apply the parking brake.


iii.

Clear the DTCs.


iv.

Bleed air from SST (LSPV gauge).

Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE FLUID>BLEEDING



c.

Check operation without brake boost.

i.

Inspect and adjust the brake pedal height.



ii.
C447617C03
2.104,1.417 2.271,1.667 2.271,1.667 2.521,1.667 true 2.063,1.021 2.813,1.021 true 2.865,0.958 3.115,1.125 0.25,0.167 10 true *a 2.573,1.604 2.823,1.771 0.25,0.167 10 true *b
*a Fluid Level Support Line
*b MIN Line


Adjust the brake fluid level of the reservoir so that it is between the MIN line and fluid level support line.


iii.

Select "Motor Deactivate" on the "ECB (Electronically Controlled Brake system) Utility" screen.

Chassis > Brake/EPB > Utility
Tester Display
ECB Utility
50005 435 3617

iv.

Perform "Motor Deactivate" according to the display on the GTS.


v.

Depress the brake pedal 40 times or more to return all the fluid in the accumulator back to the reservoir.

HINT:

A buzzer may sound due to low accumulator pressure. As this is not a malfunction, continue the procedure.



vi.

Check that the brake pedal is firm.


vii.

Check the values output from "Stroke Sensor" and "Stroke Sensor2" by depressing the brake pedal.

Chassis > Brake Booster > Data List
Tester Display
Stroke Sensor
50003 466 207
Chassis > Brake/EPB > Data List
Tester Display
Stroke Sensor2
50003 435 208
Standard Result:
Pedal Effort Stroke Sensor
(V)
Stroke Sensor2
(V)
Front Left Wheel Hydraulic Pressure Front Right Wheel Hydraulic Pressure
200 N (20 kgf, 45.0 lbf) 1.51 to 2.21 2.79 to 3.49 0 to 2.86 MPa (0.0 to 29.1 kgf/cm2, 0 to 414 psi) 0 to 2.86 MPa (0.0 to 29.1 kgf/cm2, 0 to 414 psi)
500 N (51 kgf, 112.4 lbf) 1.92 to 2.62 2.38 to 3.08 1.16 to 5.16 MPa (11.9 to 52.6 kgf/cm2, 169 to 748 psi) 1.16 to 5.16 MPa (11.9 to 52.6 kgf/cm2, 169 to 748 psi)


Standard Result:
Pedal Effort Stroke Sensor
(V)
Stroke Sensor2
(V)
Rear Left Wheel Hydraulic Pressure Rear Right Wheel Hydraulic Pressure
200 N (20 kgf, 45.0 lbf) 1.51 to 2.21 2.79 to 3.49 0 to 2.86 MPa (0.0 to 29.1 kgf/cm2, 0 to 414 psi) 0 to 2.86 MPa (0.0 to 29.1 kgf/cm2, 0 to 414 psi)
500 N (51 kgf, 112.4 lbf) 1.92 to 2.62 2.38 to 3.08 1.16 to 5.16 MPa (11.9 to 52.6 kgf/cm2, 169 to 748 psi) 1.16 to 5.16 MPa (11.9 to 52.6 kgf/cm2, 169 to 748 psi)


HINT:

Check the performance of the brake booster with master cylinder assembly by comparing the pedal force with the value of the LSPV gauge and each stroke sensor. If there is a problem, determine the state of the brake booster with master cylinder assembly by using these results together with the results from inspecting the brake pedal stroke sensor.



viii.

Remove the pedal effort gauge and SST, and bleed the brake system.

Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE FLUID>BLEEDING


ix.

Check the value output from "Accumulator Pressure".

Chassis > Brake Booster > Data List
Tester Display
Accumulator Pressure
50003 466 212
Standard Result:

15 to 21 MPa



x.

Clear the DTCs.



Hide 3.INSPECT STROKE SIMULATOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY)

a.

Check the auxiliary battery voltage.

Standard Voltage:

11 to 14 V (while the ignition switch is off)



b.

Set a pedal effort gauge.

i.

Set a pedal effort gauge.


ii.

Move the shift lever to P and apply the parking brake.


iii.

Clear the DTCs.



c.

Check operation with brake boost.

i.

Depress the brake pedal 4 or 5 times.


ii.

Check the values output from "Stroke Sensor" and "Stroke Sensor2" by depressing the brake pedal.

Chassis > Brake Booster > Data List
Tester Display
Stroke Sensor
50003 466 207
Chassis > Brake/EPB > Data List
Tester Display
Stroke Sensor2
50003 435 208
Standard Voltage:
Pedal Effort Stroke Sensor
(V)
Stroke Sensor2
(V)
50 N (5 kgf, 11.2 lbf) 1.21 to 1.91 3.09 to 3.79
100 N (10 kgf, 22.5 lbf) 1.42 to 2.12 2.88 to 3.58
150 N (15 kgf, 33.7 lbf) 1.61 to 2.31 2.69 to 3.39